Answer:
Natae Si Jordan Kaya Sya Napaihe
Explanation:
haha
uppose that 3 J of work is needed to stretch a spring from its natural length of 32 cm to a length of 49 cm. (a) How much work (in J) is needed to stretch the spring from 37 cm to 45 cm
Answer:
0.113 J
Explanation:
Applying,
w = ke²/2................. Equation 1
Where w = workdone in stretching the spring, k = spring constant, e = extension
make k the subject of the equation
k = 2w/e²................ Equation 2
From the question,
Given: w = 3 J, e = 49-32 = 17 cm = 0.17 m
Substitute these values into equation 2
k = (2×3)/0.17²
k = 6/0.17
k = 35.29 N/m
(a) if the spring from 37 cm to 45 cm,
Then,
w = ke²/2
Given: e = 45-37 = 8 cm = 0.08
w = 35.29(0.08²)/2
w = 0.113 J
Assuming the atmospheric pressure is 1 atm at sea level, determine the atmospheric pressure at Badwater (in Death Valley, California) where the elevation is 86.0 m below sea level.
Answer:
Atmospheric pressure at Badwater is 1.01022 atm
Explanation:
Data given:
1 atmospheric pressure (Pi) = 1.01 * 10[tex]^{5}[/tex] Pa
Elevation (h) = 86m
gravity (g) = 9.8 m/s2
Density of air P = 1.225 kg/m3
Therefore pressure at bad water Pb = Pi + Pgh
Pb = (1.01 * 10[tex]^{5}[/tex]) + (1.225 * 9.8 * 86)
Pb = (1.01 * 10[tex]^{5}[/tex]) + 1032.43 = 102032 Pa
hence:
Pb = 102032 /1.01 * 10[tex]^{5}[/tex] = 1.01022 atm
No esporte coletivo, um dos principais fatores desenvolvidos é o desenvolvimento social. Qual desses não faz parte das virtudes ensinadas no esporte?
Companheirismo
Humildade
Ser justo (Fair Play)
Vencer independente do que precise ser feito
Answer:
fair palybtgshsisuehdh
Question 7 of 10
A railroad freight car with a mass of 32,000 kg is moving at 2.0 m/s when it
runs into an at-rest freight car with a mass of 28,000 kg. The cars lock
together. What is their final velocity?
A.1.1 m/s
B. 2.2 m/s
C. 60,000 kg•m/s
D. 0.5 m/s
Answer:
a
Explanation:
you take 32,000kg ÷2.0m
After de Broglie proposed the wave nature of matter, Davisson and Germer demonstrated the wavelike behavior of electrons by observing an interference pattern from electrons scattering off what
Answer:
Scattering is an interaction that can happen when a given particle or wave, like an electron, impacts a target or material. Then the electron changes it's original path and leaves some energy in the process. (This is a really simplified explanation of scattering, this is a really complex phenomenon, but let's not dive into that path)
Particularly, Davisson and Germer used a beam of electrons against a target of nickel, and these scattered electrons were detected by a detector. All of that in a vacuum chamber.
Then the correct answer is a nickel target.
"After de Broglie proposed the wave nature of matter, Davisson and Germer demonstrated the wavelike behavior of electrons by observing an interference pattern from electrons scattering off a nickel target"
a girl is moving with a uniform velocity of 1.5 m/s then mathematically find her acceleration
Answer:
0
Explanation:
a = dv/dt
if v is constant than the slope of the v graph will be 0, so dv/dt is 0
a= 0
Two pistons are connected to a fluid-filled reservoir. The first piston has an area of 3.002 cm2, and the second has an area of 315 cm2. If the first cylinder is pressed inward with a force of 50.0 N, what is the force that the fluid in the reservoir exerts on the second cylinder?
Answer:
The force on the second piston is 5246.5 N .
Explanation:
Area of first piston, a = 3.002 cm^2
Area of second piston, A = 315 cm^2
Force on first piston, f = 50 N
let the force of the second piston is F.
According to the Pascal's law
[tex]\frac{f}{a} = \frac{F}{A}\\\\\frac{50}{3.002}=\frac{F}{315}\\\\F = 5246.5 N[/tex]
A nerve impulse travels along a myelinated neuron at 90.1 m/s.
What is this speed in mi/h?
Answer:
201.5537 mph
Explanation:
Given the following data;
Speed = 90.1 m/s
Speed can be defined as distance covered per unit time. Speed is a scalar quantity and as such it has magnitude but no direction.
Mathematically, speed is given by the formula;
Speed = distance/time
To convert this value into miles per hour;
Conversion;
1 meter = 0.000621 mile
90.1 meters = 90.1 * 0.000621 = 0.05595 miles
1 metre per second = 2.237 miles per hour
90.1 meters per seconds = 90.1 * 2.237 = 201.5537 miles per hour
90.1 m/s = 201.5537 mph
1. A 20.0 N force directed 20.0° above the horizontal is applied to a 6.00 kg crate that is traveling on a horizontal
surface. What is the magnitude of the normal force exerted by the surface on the crate?
N = 52.0 N
Explanation:
Given: [tex]F_a= 20.0\:\text{N}=\:\text{applied\:force}[/tex]
[tex]m=6.00\:\text{kg}[/tex]
[tex]N = \text{normal force}[/tex]
The net force [tex]F_{net}[/tex] is given by
[tex]F_{net} = N + F_a\sin 20 - mg=0[/tex]
Solving for N, we get
[tex]N = mg - F_a\sin 20[/tex]
[tex]\:\:\:\:\:\:= (6.00\:\text{kg})(9.8\:\text{m/s}^2) - (20.0\:\text{N}\sin 20)[/tex]
[tex]\:\:\:\:\:\:= 52.0\:\text{N}[/tex]
What are the differences among elements, compounds, and mixtures?
Answer:
Elements have a characteristic number of electrons and protons.Both Hydrogen(H) and oxygen(O) are two different elements.
••••••••••••••••
Compounds are chemical substances where the atoms atoms of two different elements are combined together. It is made of .Hydrogen(H) and Oxygen(O) both qr4 naturally gases,but they react to form water(H2O),which is liquid compound.
•••••••••••••••
A mixture is made of atleast two parts》 solid,liquid or gas.The difference is that it's not a chemical substance that's bonded by other elements.
------------------------------
Hope it helps...
Have a great day!!!
Answer: Elements have a characteristic number of electrons and protons. Both Hydrogen(H) and oxygen(O) are two different elements. Compounds are chemical substances where the atoms atoms of two different elements are combined together. It is made of.Hydrogen(H) and Oxygen(O) both qr4 naturally gases, but they react to form water(H2O), which is liquid compound. A mixture is made of at least two parts solid, liquid, or gas. The difference is that it's not a chemical substance that's bonded by other elements.
A cylindrical disk of wood weighing 45.0 N and having a diameter of 30.0 cm floats on a cylinder of oil of density 0.850 g>cm3 (Fig. E12.19). The cylinder of oil is 75.0 cm deep and has a diameter the same as that of the wood. (a) What is the gauge pressure at the top of the oil column
Answer:
665.25 Pa
Explanation:
Given data :
Weight of the disk, w = 45 N
Diameter, d = 30 cm
= 0.30 m
Therefore, radius of the disk,
[tex]$r=\frac{d}{2}$[/tex]
[tex]$r=\frac{0.30}{2}$[/tex]
= 0.15 m
Now, area of the cylindrical disk,
[tex]$A=\pi r^2$[/tex]
[tex]$A=3.14 \times (0.15)^2$[/tex]
[tex]$=0.07065 \ m^2$[/tex]
∴ The gauge pressure at the top of the oil column is :
[tex]$p=\frac{w}{A}$[/tex]
[tex]$p=\frac{47}{0.07065}$[/tex]
= 665.25 Pa
Therefore, the gauge pressure is 665.25 Pa.
The definition of pressure allows to find the result for the pressure at the top of the oil cylinder is:
The pressure is: P = 636.6 Pa
The pressure is defined by the relationship between perpendicular force and area.
[tex]P = \frac{F}{A}[/tex]
where P is pressure, F is force, and A is area.
They indicate that the wooden cylinder weighs W = 45.0 N and has a diameter of d = 30 cm = 0.30 m.
The area is:
A = π r² = [tex]\pi \frac{d^2}{4}[/tex]
In the attachment we see a diagram of the forces, where the weight of the cylinder and the thrust are equal.
B-W = 0
B = W
The force applied to the liquid is the weights of the cylinder. Let's replace.
[tex]P= \frac{W}{A} \\P = W \frac{4}{\pi d^2 }[/tex]
Let's calculate.
[tex]P = \frac{45 \ 4 }{\pi \ 0.30^2 }[/tex] P = 45 4 / pi 0.30²
P = 636.6 Pa
In conclusion using the definition of pressure we can find the result for the pressure at the top of the oil cylinder is:
The pressure is: P = 636.6 Pa.
Learn more about pressure here: brainly.com/question/17467912
A wave moves in a rope with a certain wavelength. A second wave is made to move in the same rope with twice the wavelength of the first wave. The frequency of the second wave is _______________ the frequency of the first wave.
Answer:
The frequency of the second wave is half of the frequency of first one.
Explanation:
The wavelength of the second wave is double is the first wave.
As we know that the frequency is inversely proportional to the wavelength of the velocity is same.
velocity = frequency x wavelength
So, the ratio of frequency of second wave to the first wave is
[tex]\frac{f_2}{f_1} =\frac{\lambda _1}{\lambda _2}\\\\\frac{f_2}{f_1} =\frac{\lambda _1}{2\lambda _1}\\\\\frac{f_2}{f_1} =\frac{1}{2}\\\\[/tex]
The frequency of the second wave is half of the frequency of first one.
A copper wire 1.0 meter long and with a mass of .0014 kilograms per meter vibrates in two segments when under a tension of 27 Newtons. What is the frequency of this mode of vibration
Answer:
the frequency of this mode of vibration is 138.87 Hz
Explanation:
Given;
length of the copper wire, L = 1 m
mass per unit length of the copper wire, μ = 0.0014 kg/m
tension on the wire, T = 27 N
number of segments, n = 2
The frequency of this mode of vibration is calculated as;
[tex]F_n = \frac{n}{2L} \sqrt{\frac{T}{\mu} } \\\\F_2 = \frac{2}{2\times 1} \sqrt{\frac{27}{0.0014} }\\\\F_2 = 138.87 \ Hz[/tex]
Therefore, the frequency of this mode of vibration is 138.87 Hz
A wheel rotates about a fixed axis with an initial angular velocity of 13 rad/s. During a 8-s interval the angular velocity increases to 57 rad/s. Assume that the angular acceleration was constant during this time interval. How many revolutions does the wheel turn through during this time interval
Answer:
The number of revolutions is 44.6.
Explanation:
We can find the revolutions of the wheel with the following equation:
[tex]\theta = \omega_{0}t + \frac{1}{2}\alpha t^{2}[/tex]
Where:
[tex]\omega_{0}[/tex]: is the initial angular velocity = 13 rad/s
t: is the time = 8 s
α: is the angular acceleration
We can find the angular acceleration with the initial and final angular velocities:
[tex] \omega_{f} = \omega_{0} + \alpha t [/tex]
Where:
[tex] \omega_{f} [/tex]: is the final angular velocity = 57 rad/s
[tex] \alpha = \frac{\omega_{f} - \omega_{0}}{t} = \frac{57 rad/s - 13 rad/s}{8 s} = 5.5 rad/s^{2} [/tex]
Hence, the number of revolutions is:
[tex] \theta = \omega_{0}t + \frac{1}{2}\alpha t^{2} = 13 rad/s*8 s + \frac{1}{2}*5.5 rad/s^{2}*(8 s)^{2} = 280 rad*\frac{1 rev}{2\pi rad} = 44.6 rev [/tex]
Therefore, the number of revolutions is 44.6.
I hope it helps you!
two identical eggs are dropped from the same height. The first eggs lands on a dish and breaks, while the second lands on a pillow and does not break. Which quantities are the same in both situations
Answer:
The height is the same
Explanation:
Because they were at the same height but they fell at different velocities
Traveling waves propagate with a fixed speed usually denoted as v (but sometimes c). The waves are called __________ if their waveform repeats every time interval T.
a. transverse
b. longitudinal
c. periodic
d. sinusoidal
Answer:
periodic
Explanation:
A 1.40-kg block is on a frictionless, 30 ∘ inclined plane. The block is attached to a spring (k = 40.0 N/m ) that is fixed to a wall at the bottom of the incline. A light string attached to the block runs over a frictionless pulley to a 60.0-g suspended mass. The suspended mass is given an initial downward speed of 1.60 m/s .
How far does it drop before coming to rest? (Assume the spring is unlimited in how far it can stretch.)
Express your answer using two significant figures.
Answer:
0.5
Explanation:
because the block is attached to the pulley of the string
A charge of 0.20uC is 30cm from a point charge of 3.0uC in vacuum. what work is required to bring the 0.2uC charge 18cm closer to the 3.0uC charge?
Answer:
The correct answer is "[tex]4.49\times 10^{10} \ joules[/tex]".
Explanation:
According to the question,
The work will be:
⇒ [tex]Work=-\frac{kQq}{R}[/tex]
[tex]=-\frac{1}{4 \pi \varepsilon \times (18-30)\times 3\times 0.2}[/tex]
[tex]=-\frac{1}{4 \pi \varepsilon \times (-12)\times 3\times 0.2}[/tex]
[tex]=\frac{0.3978}{\varepsilon }[/tex]
[tex]=4.49\times 10^{10} \ joules[/tex]
Thus the above is the correct answer.
We have that the workdone is mathematically given as
W=4.49*10e10 J
From the question we are told
A charge of 0.20uC is 30cm from a point charge of 3.0uC in vacuum. what work is required to bring the 0.2uC charge 18cm closer to the 3.0uC charge?WorkdoneGenerally the equation for the workdone is mathematically given as
W=-kQq/R
Therefore
0.3978/ε0 =-1/(4πε0*(18-30)*3*0.2
Hence
W=4.49*10e10 JFor more information on Charge visit
https://brainly.com/question/9383604
The slope of a d vs t graph represents velocity. Describe 3 ways you know this to be true.
Answer:
Look at explanation
Explanation:
I only know 1 way, there is another way you can rephrase this using derivatives but that's pretty much the same thing.
The slope is calculated by Δy/Δx so the slope of distance vs time graph is Δd/Δt which is the velocity
The density of blood is 1055 kg/m3 . If the blood at the very top of your head exerts a minimum gauge pressure of 45 mm Hg (6000 Pa), estimate the gauge pressure at your heart in pascals.
Answer:
P = 10135.6 Pa
Explanation:
For this exercise we use that the pressure varies with the height
P = P₀ + ρ g h
where h is the height from the head to the heart, which is approximately
h = 40 cm = 0.40m and P₀ is the head pressure P₀ = 6000 Pa
P = 6000 + 1055 9.8 0.40
P = 6000 + 4135.6
P = 10135.6 Pa
The correct equation for the x component of a vector named A with an angle measured from the x axis would be which of the following?
Answer:
Acosθ
Explanation:
The x-component of a vector is defined as :
Magnitude * cosine of the angle
Maginitude * cosθ
The magnitude is represented as A
Hence, horizontal, x - component of the vector is :
Acosθ
Furthermore,
The y-component is taken as the sin of the of the angle multiplied by the magnitude
Vertical, y component : Asinθ
A 6.0-cm-diameter horizontal pipe gradually narrows to 4.0 cm. When water flows through this pipe at a certain rate, the gauge pressure in these two sections is 32.0 kPa and 24.0 kPa, respectively. What is the volume rate of flow?
Answer:
a n c
Explanation:
A 0.500-kg block slides up a plane inclined at a 30° angle. If it slides 1.50 m before coming to rest while encountering a frictional force of 2 N, find (a) its acceleration, and (b) its initial velocity.
It takes 130 J of work to compress a certain spring 0.10m. (a) What is the force constant of this spring? (b) To compress the spring an additional 0.10 m, does it take 130 J, more than 130 J or less than 130 J? Verify your answer with a calculation.
Explanation:
Given that,
Work done to stretch the spring, W = 130 J
Distance, x = 0.1 m
(a) We know that work done in stretching the spring is as follows :
[tex]W=\dfrac{1}{2}kx^2\\\\k=\dfrac{2W}{x^2}\\\\k=\dfrac{2\times 130}{(0.1)^2}\\\\k=26000\ N/m[/tex]
(b) If additional distance is 0.1 m i.e. x = 0.1 + 0.1 = 0.2 m
So,
[tex]W=\dfrac{1}{2}kx^2\\\\W=\dfrac{1}{2}\times 26000\times 0.2^2\\\\W=520\ J[/tex]
So, the new work is more than 130 J.
how can scientific method solve real world problems examples
A football quarterback runs 15.0 m straight down the playing field in 3.00 s. He is then hit and pushed 3.00 m straight backward in 1.71 s. He breaks the tackle and runs straight forward another 24.0 m in 5.20 s. Calculate his average velocity (in m/s) for the entire motion. (Assume the quarterback's initial direction is positive. Indicate the direction with the sign of your answer.)
Answer:
Average Velocity = 3.63 m/s
Explanation:
First, we will calculate the total displacement of the quarterback, taking forward direction as positive:
Total Displacement = 15 m - 3 m + 24 m = 36 m
Now, we will calculate the total time taken for this displacement:
Total Time = 3 s + 1.71 s + 5.2 s = 9.91 s
Therefore, the average velocity will be:
[tex]Average\ Velocity = \frac{Total\ Displacement}{Total\ Time}\\\\Average\ Velocity = \frac{36\ m}{9.91\ s}[/tex]
Average Velocity = 3.63 m/s
If an electrical component with a resistance of 53 Q is connected to a 128-V source, how much current flows through the component?
Answer:
the current that flows through the component is 2.42 A
Explanation:
Given;
resistance of the electrical component, r = 53 Ω
the voltage of the source, V = 128 V
The current that flows through the component is calculated using Ohm's Law as demonstrated below;
[tex]V = IR\\\\I = \frac{V}{R} = \frac{128 \ V}{53 \ ohms} = 2.42 \ A[/tex]
Therefore, the current that flows through the component is 2.42 A
You walk into a room and you see 4 chickens on a bed 2 cows on the floor and 2 cats in a chair. How many legs are on the ground? (I know this answer just a riddle to see who knows it) (:
Answer:
18
Explanation:
I'm pretty sure I got it right
3. You have a variable-voltage power supply and a capacitor in the form of two metal disks of radius 0.6 m, held a distance of 1 mm apart. What is the largest voltage you can apply to the capacitor without the air becoming highly conductive
Answer:
The breakdown of air occurs at a maximum voltage of 3kV/mm.
Explanation:
The breakdown of air occurs at a maximum voltage of 3kV/mm.
At this level of voltage the air between the plates become highly ionised and breakdown occurs. Since, the distance held between the plates is 1mm , it can withstand a maximum voltage of 3 kV.
After this voltage the air will become conductive in nature and will form ions in the air between the plates and ultimately breakdown will take place with a flash.
A car hurtles off a cliff and crashes on the canyon floor below. Identify the system in which the net momentum is zero during the crash.
Solution :
It is given that a car ran off from a cliff and it crashes on canyon floor. Now the system of a car as well as the earth together have a [tex]\text{ net momentum of zero}[/tex] when the car crashes on the canyon floor, thus reducing the momentum of the car to zero. The earth also stops its upward motion and it also reduces the momentum to zero.
