When a ray of light passes from glass to water it is?

Answers

Answer 1

Answer:

[tex]\huge\boxed{Refracted}[/tex]

Explanation:

When a ray of light passes from glass to water, it

1) is Slightly refracted (bending of light)

2) moves away from the normal.

Whenever a light ray travels from a denser medium to a rarer medium, it bends away from the normal.

Answer 2

Answer:

refraction

Explanation:


Related Questions

A sharp edged orifice with a 60 mm diameter opening in the vertical side of a large tank discharges under a head of 6 m. If the coefficient of contraction is 0.68 and the coefficient of velocity is 0.92, what is the discharge?

Answers

Answer:

The discharge rate is [tex]Q = 0.0192 \ m^3 /s[/tex]

Explanation:

From the question we are told that

   The  diameter is  [tex]d = 60 \ mm = 0.06 \ m[/tex]

    The  head is  [tex]h = 6 \ m[/tex]

     The  coefficient of contraction is  [tex]Cc = 0.68[/tex]

     The  coefficient of  velocity is  [tex]Cv = 0.92[/tex]

The radius is mathematically evaluated as

         [tex]r = \frac{d}{2}[/tex]

substituting values

        [tex]r = \frac{ 0.06 }{2}[/tex]

        [tex]r = 0.03 \ m[/tex]

The  area is mathematically represented as

      [tex]A = \pi r^2[/tex]

substituting values

      [tex]A = 3.142 * (0.03)^2[/tex]

      [tex]A = 0.00283 \ m^2[/tex]

 The  discharge rate is mathematically represented as

        [tex]Q = Cv *Cc * A * \sqrt{ 2 * g * h}[/tex]

substituting values

       [tex]Q = 0.68 * 0.92* 0.00283 * \sqrt{ 2 * 9.8 * 6}[/tex]

       [tex]Q = 0.0192 \ m^3 /s[/tex]

A rectangular coil lies flat on a horizontal surface. A bar magnet is held above the center of the coil with its north pole pointing down. What is the direction of the induced current in the coil?

Answers

Answer:

There is no induced current on the coil.

Explanation:

Current is induced in a coil or a circuit, when there is a break of flux linkage. A break in flux linkage is caused by a changing magnetic field, and must be achieved by a relative motion between the coil and the magnet. Holding the magnet above the center of the coil will cause no changing magnetic filed since there is no relative motion between the coil and the magnet.

A resistance heater having 20.7 kW power is used to heat a room having 16 m X 16.5 m X 12.3 m size from 13.5 to 21 oC at sea level. The room is sealed once the heater is turned on. Calculate the amount of time needed for this heating to occur in min. (Write your answer in 3 significant digits. Assume constant specific heats at room temperature.)

Answers

Answer:

t = 23.6 min

Explanation:

First we need to find the mass of air in the room:

m = ρV

where,

m = mass of air in the room = ?

ρ = density of air at room temperature = 1.2041 kg/m³

V = Volume of room = 16 m x 16.5 m x 12.3 m = 3247.2 m³

Therefore,

m = (1.2041 kg/m³)(3247.2 m³)

m = 3909.95 kg

Now, we find the amount of energy consumed to heat the room:

E = m C ΔT

where,

E = Energy consumed = ?

C = Specific Heat of air at room temperature = 1 KJ/kg.⁰C

ΔT = Change in temperature = 21 °C - 13.5 °C = 7.5 °C

Therefore,

E = (3909.95 kg)(1 KJ/kg.°C)(7.5 °C)

E = 29324.62 KJ

Now, the time period can be calculated as:

P = E/t

t = E/P

where,

t = Time needed = ?

P = Power of heater = 20.7 KW

Therefore,

t = 29324.62 KJ/20.7 KW

t = (1416.65 s)(1 min/60 s)

t = 23.6 min

A steel ball attached to a spring moves in simple harmonic motion. The amplitude of the ball's motion is 11.0 cm, and the spring constant is 6.00 N/m. When the ball is halfway between its equilibrium position and its maximum displacement from equilibrium, its speed is 26.1 cm/s. (a) What is the mass of the ball (in kg)? kg (b) What is the period of oscillation (in s)? s (c) What is the maximum acceleration of the ball? (Enter the magnitude in m/s2.) m/s2

Answers

Answer:

a) m = 0.626 kg , b) T = 2.09 s , c)   a = 1.0544 m / s²

Explanation:

In a spring mass system the equation of motion is

        x = A cos (wt + Ф)

with      w = √(k / m)

a) velocity is defined by

        v = dx / dt

        v = - A w sin (wt + Ф)          (1)

give us that the speed is

        v = 26.1 m / s

for the point

        x = a / 2

the range of motion is a = 11.0 cm

       x = 11.0 / 2

       x = 5.5 cm

Let's find the time it takes to get to this distance

       wt + Ф = cos⁻¹ (x / A)

       wt + Ф = cos 0.5

        wt + Ф = 0.877

In the exercise they do not indicate that the body started its movement with any speed, therefore we assume that for the maximum elongation the body was released, therefore the phase is zero f

       Ф = 0

       wt = 0.877

       t = 0.877 / w

we substitute in equation 1

       26.1 = -11.0 w sin (w 0.877 / w)

        w = 26.1 / (11 sin 0.877))

        w = 3.096 rad / s

from the angular velocity equation

       w² = k / m

       m = k / w²

       m = 6 / 3,096²

       m = 0.626 kg

b) angular velocity and frequency are related

       w = 2π f

frequency and period are related

        f = 1 / T

we substitute

        w = 2π / T

        T = 2π / w

        T = 2π / 3,096

        T = 2.09 s

c) maximum acceleration

 the acceleration of defined by

        a = dv / dt

        a = - Aw² cos (wt)

the acceleration is maximum when the cosine is ±1

         a = A w²

          a = 11  3,096²

        a = 105.44 cm / s²

we reduce to m / s

        a = 1.0544 m / s²

Astronomers discover an exoplanet (a planet of a star other than the Sun) that has an orbital period of 3.75
Earth years in its circular orbit around its sun, which is a star with a measured mass of 3.23×1030kg
. Find the radius of the exoplanet's orbit.

Answers

Answer:

[tex]r=4.24\times 10^{11}\ m[/tex]

Explanation:

Given that,

Orbital time period, T = 3.75 earth years

Mass of star, [tex]m=3.23\times 10^{30}\ kg[/tex]

We need to find the radius of the exoplanet's orbit. It is a concept of Kepler's third law of motion i.e.

[tex]T^2=\dfrac{4\pi^2}{GM}r^3[/tex]

r is the radius of the exoplanet's orbit.

Solving for r we get :

[tex]r=(\dfrac{T^2GM}{4\pi^2})^{1/3}[/tex]

We know that, [tex]1\ \text{earth year}=3.154\times 10^7\ \text{s}[/tex]

So,

[tex]r=(\dfrac{(3.75\times 3.154\times 10^7)^2\times 6.67\times 10^{-11}\times 3.23\times 10^{30}}{4\pi^2})^{1/3}\\\\r=4.24\times 10^{11}\ m[/tex]

So, the radius of the exoplanet's orbit is [tex]4.24\times 10^{11}\ m[/tex].

The law of reflection is quite useful for mirrors and other flat, shiny surfaces. (This sort of reflection is called specular reflection). However, you've likely been told that when you look at something, you are seeing light reflected from the object that you are looking at. This is reflection of a different sort of diffuse reflection.

Suppose that the spotlight shines so that different parts of the beam reflect off of different two surfaces, one inclined at an angle alpha (from the horizontal) and one inclined at an angle beta. What would the angular separation between the rays reflected from the two surfaces?

Answers

Answer:

Explanation:

Suppose initially the plane was horizontal and light was reflected back at some angle θ from the normal .

Now the reflecting surface is twisted so that is becomes inclined at angle alpha .

The reflected light will be deviated from its original direction by angle

2 x alpha .

Similarly when the reflecting surface is further twisted so that it becomes inclined at angle beta then again the reflected beam will deviated by angle

2 x beta

Hence angle between these two reflected beam

= 2 beta - 2 alpha

= 2 ( β - α )

So, angular separation between the rays reflected from the two surfaces

= 2 ( β - α ) .

"In a Young's double-slit experiment, the slit separation is doubled. To maintain the same fringe spacing on the screen, the screen-to-slit distance D must be changed to"

Answers

Answer:

To maintain the same fringe spacing on the screen, the screen-to-slit distance D must be changed to a value 2D that is twotimes D

Monochromatic light falls on two very narrow slits 0.047 mm apart. Successive fringes on a screen 6.60 m away are 8.9 cm apart near the center of the pattern.
Determine the wavelength and frequency of the light.

Answers

Answer::

   [tex]\lambda = 634 nm[/tex]

  [tex]f = 4.73 *10^{14} \ Hz[/tex]

Explanation:

From the question we are told that

      The  distance of separation is  [tex]d = 0.047 \ mm = 0.047 *10^{-3} \ m[/tex]

       The  distance of the screen is  [tex]D = 6.60 \ m[/tex]

      The  width of the fringe is [tex]y = 8.9 \ cm = 0.089 \ m[/tex]

     

Generally the width of the width of the fringes is mathematically represented as

          [tex]y = \frac{\lambda * D }{d }[/tex]

=>       [tex]\lambda = \frac{y * d }{D }[/tex]

=>      [tex]\lambda = \frac{ 0.089 * (0.047 *10^{-3}) }{6.60 }[/tex]

=>    [tex]\lambda = 634 *10^{-9}[/tex]

=>  [tex]\lambda = 634 nm[/tex]

Generally the speed of light is mathematically represented as

         [tex]c = f * \lambda[/tex]

=>       [tex]f= \frac{ c}{\lambda }[/tex]

=>         [tex]f= \frac{ 3.0 *10^{8}}{634 *10^{-9}}[/tex]

=>     [tex]f = 4.73 *10^{14} \ Hz[/tex]

The electric field 2.8 cm from a small object points toward the object with a strength of 180,000 N/C. What is the object's charge?

Answers

Answer:

2.1×10¹⁸ C

Explanation:

Using,

E = kq/r²...................... Equation 1

Where E = Electric field, q = charge, r = distance, k = coulombs constant.

make q the subject of the equation

q = Er²/k.................. Equation 2

Given: E = 180000 N/C, r = 2.8 cm = 0.028 m

Constant: k = 9×10⁹ Nm²/C².

Substitute these values into equation 2

q = 180000(9×10⁹)/0.028²

q = 2.1×10¹⁸ C

Hence the object charge is 2.1×10¹⁸ C

g A projectile is fired from the ground at an angle of θ = π 4 toward a tower located 600 m away. If the projectile has an initial speed of 120 m/s, find the height at which it strikes the tower

Answers

Answer:

The projectile strikes the tower at a height of 354.824 meters.

Explanation:

The projectile experiments a parabolic motion, which consist of a horizontal motion at constant speed and a vertical uniformly accelerated motion due to gravity. The equations of motion are, respectively:

Horizontal motion

[tex]x = x_{o}+v_{o}\cdot t \cdot \cos \theta[/tex]

Vertical motion

[tex]y = y_{o} + v_{o}\cdot t \cdot \sin \theta +\frac{1}{2} \cdot g \cdot t^{2}[/tex]

Where:

[tex]x_{o}[/tex], [tex]x[/tex] - Initial and current horizontal position, measured in meters.

[tex]y_{o}[/tex], [tex]y[/tex] - Initial and current vertical position, measured in meters.

[tex]v_{o}[/tex] - Initial speed, measured in meters per second.

[tex]g[/tex] - Gravitational acceleration, measured in meters per square second.

[tex]t[/tex] - Time, measured in seconds.

The time spent for the projectile to strike the tower is obtained from first equation:

[tex]t = \frac{x-x_{o}}{v_{o}\cdot \cos \theta}[/tex]

If [tex]x = 600\,m[/tex], [tex]x_{o} = 0\,m[/tex], [tex]v_{o} = 120\,\frac{m}{s}[/tex] and [tex]\theta = \frac{\pi}{4}[/tex], then:

[tex]t = \frac{600\,m-0\,m}{\left(120\,\frac{m}{s} \right)\cdot \cos \frac{\pi}{4} }[/tex]

[tex]t \approx 7.071\,s[/tex]

Now, the height at which the projectile strikes the tower is: ([tex]y_{o} = 0\,m[/tex], [tex]t \approx 7.071\,s[/tex], [tex]v_{o} = 120\,\frac{m}{s}[/tex] and [tex]g = -9.807\,\frac{m}{s^{2}}[/tex])

[tex]y = 0\,m + \left(120\,\frac{m}{s} \right)\cdot (7.071\,s)\cdot \sin \frac{\pi}{4}+\frac{1}{2}\cdot \left(-9.807\,\frac{m}{s^{2}} \right) \cdot (7.071\,s)^{2}[/tex]

[tex]y \approx 354.824\,m[/tex]

The projectile strikes the tower at a height of 354.824 meters.

What is the maximum wavelength of incident light for which photoelectrons will be released from gallium

Answers

Answer:

292 nm

Explanation:

The work function of gallium ∅ = 94.25 eV = 6.81 x 10^-19 J

at maximum wavelength, the energy of the photons is equal to its work function

Energy of the electron = hf

but hf = hc/λ

where h is the planck's constant = 6.63 × 10-34 m^2 kg/s

c is the speed of light = 3 x 10^8 m/s

λ is the wavelength that this occurs, which is the maximum wavelength

Equating, we have

hc/λ =  ∅

substituting, we have

(6.63 × 10-34 x 3 x 10^8)/λ = 6.81 x 10^-19

(1.989 x 10^-25)/(6.81 x 10^-19) = λ

λ = 292.07 x 10^-9 = 292 nm

Which scientist proposed a mathematical solution for the wave nature of light?

Answers

Answer:

Explanation:

Christian Huygens

Light Is a Wave!

Then, in 1678, Dutch physicist Christian Huygens (1629 to 1695) established the wave theory of light and announced the Huygens' principle.

PLEASE HELP WILL GIVE BRAINLIEST In an experiment, the hypothesis is that if leaf color is related to temperature, then exposing the plant to low temperatures will result in a leaf color change . This hypothesis is _____. 1. testable 2.falsifiable 3.a and b above 4.none of the above

Answers

Answer:

testable

Explanation:

high heat can cause browning and or welting

Answer:

A

Explanation:

If it is tested, it will really changed when the plant into low temperature

1. Suppose that a solid ball, a solid disk, and a hoop all have the same mass and the same radius. Each object is set rolling without slipping up an incline with the same initial linear (translational) speed. Which goes farthest up
the incline?
a. the ball
b. the disk
c. the hoop
d. the hoop and the disk roll to the same height, farther
than the ball
e. they all roll to the same height
2. Suppose that a solid ball, a solid disk, and a hoop all have the same mass and the same radius. Each object is set rolling with slipping up an incline with the same initial linear (translational) speed. Which goes farthest up
the incline?
a. the ball
b. the disk
c. the hoop
d. the hoop and the disk roll to the same height, farther
than the ball
e. they all roll to the same height

Answers

Answer:

The hoop

Explanation:

Because it has a smaller calculated inertia of 2/3mr² compares to the disc

A mass M slides downward along a rough plane surface inclined at angle \Theta\:Θ= 32.51 in degrees relative to the horizontal. Initially the mass has a speed V_0\:V 0 = 6.03 m/s, before it slides a distance L = 1.0 m down the incline. During this sliding, the magnitude of the power associated with the work done by friction is equal to the magnitude of the power associated with the work done by the gravitational force. What is the coefficient of kinetic friction between the mass and the incline?

Answers

Answer: μ = 0.8885

Explanation: Force due to friction is calculated as: [tex]F_{f} = \mu.N[/tex]

At an inclined plane, normal force (N) is: N = mgcosθ, in which θ=32.51.

Power associated with work done by friction is [tex]P=F_{f}.x[/tex]. The variable x is displacement the object "spent its energy".

Power associated with work done by gravitational force is P = mghcosθ, where h is height.

The decline forms with horizontal plane a triangle as draw in the picture.

To determine force due to friction:

[tex]F_{f}.x=mghcos(\theta)[/tex]

[tex]F_{f}=\frac{mghcos(\theta)}{x}[/tex]

Replacing force:

[tex]\frac{m.g.h.cos(\theta)}{x} = \mu.m.g.cos(\theta)[/tex]

[tex]\mu=\frac{h}{x}[/tex]

Calculating h using trigonometric relations:

[tex]sin(32.51) = \frac{h}{1}[/tex]

h = sin(32.51)

Coefficient of Kinetic friction is

[tex]\mu=\frac{sin(32.51)}{1}[/tex]

μ = 0.8885

For these conditions, coefficient of kinetic friction is μ = 0.8885.

Which is one criterion that materials of a technological design should meet? They must be imported. They must be affordable. They must be naturally made. They must be locally produced.

Answers

Answer:

they must be affordable because they have to pay for it or they wont get the stuff they are bying.

Explanation:

need a brainliest please.

Answer: B, they must be affordable.

Explanation:

To get an idea of the order of magnitude of inductance, calculate the self-inductance in henries for a solenoid with 1500 loops of wire wound on a rod 13 cm long with radius 2 cm

Answers

Answer:

The self-inductance in henries for the solenoid is 0.0274 H.

Explanation:

Given;

number of turns, N = 1500 turns

length of the solenoid, L = 13 cm = 0.13 m

radius of the wire, r = 2 cm = 0.02 m

The self-inductance in henries for a solenoid is given by;

[tex]L = \frac{\mu_oN^2A}{l}[/tex]

where;

[tex]\mu_o[/tex] is permeability of free space = [tex]4\pi*10^{-7} \ H/m[/tex]

A is the area of the solenoid = πr² = π(0.02)² = 0.00126 m²

[tex]L = \frac{4\pi *10^{-7}(1500)^2*(0.00126)}{0.13} \\\\L = 0.0274 \ H[/tex]

Therefore, the self-inductance in henries for the solenoid is 0.0274 H.

Expectant mothers many times see their unborn child for the first time during an ultrasonic examination. In ultrasonic imaging, the blood flow and heartbeat of the child can be measured using an echolocation technique similar to that used by bats. For the purposes of these questions, please use 1500 m/s as the speed of sound in tissue. I need help with part B and C
To clearly see an image, the wavelength used must be at most 1/4 of the size of the object that is to be imaged. What frequency is needed to image a fetus at 8 weeks of gestation that is 1.6 cm long?
A. 380 kHz
B. 3.8 kHz
C. 85 kHz
D. 3.8 MHz

Answers

Answer:

380 kHz

Explanation:

The speed of sound is taken as 1500 m/s

The length of the fetus is 1.6 cm long

The condition is that the wavelength used must be at most 1/4 of the size of the object that is to be imaged.

For this 1.6 cm baby, the wavelength must not exceed

λ = [tex]\frac{1}{4}[/tex] of 1.6 cm = [tex]\frac{1}{4}[/tex] x 1.6 cm = 0.4 cm =

0.4 cm = 0.004 m   this is the wavelength of the required ultrasonic sound.

we know that

v = λf

where v is the speed of a wave

λ is the wavelength of the wave

f is the frequency of the wave

f = v/λ

substituting values, we have

f = 1500/0.004 = 375000 Hz

==> 375000/1000 = 375 kHz ≅ 380 kHz

A sinusoidal electromagnetic wave is propagating in a vacuum in the +z-direction. If at a particular instant and at a certain point in space the electric field is in the +x-direction and has a magnitude of 4.00 V/m, what is the magnitude of the magnetic field of the wave at this same point in space and instant in time?

Answers

Answer:

B = 1.33 10⁻⁸ T , the magnetic field must be in the y + direction

Explanation:

In an electromagnetic wave the electric and magnetic fields are in phase

         c = E / B

         B = E / c

let's calculate

          B = 4.00 / 3 10⁸

          B = 1.33 10⁻⁸ T

To determine the direction we use that the electric and magnetic fields and the speed of the wave are perpendicular.

 If the wave advances in the + Z direction and the electric field is in the + x direction, the magnetic field must be in the y + direction

light bulb is connected to a 110-V source. What is the resistance of this bulb if it is a 100-W bulb

Answers

Answer:

121ohms

Explanation:

Formula used for calculating power P = current * voltage

P = IV

From ohms law, V = IR where R is the resistance. Substituting V = IR into the formula for calculating power, we will have;

P = IV

P =(V/R)V

P = V²/R

Given parameters

Power rating of the bulb P = 100 Watts

Source voltage V = 110V

Required

Resistance of the bulb R

Substituting the given parameters into the formula for calculating power to get Resistance R;

P = V²/R

100 = 110²/R

R = 110²/100

R = 110 * 110/100

R = 12100/100

R = 121 ohms

Hence, the resistance of this bulb is 121 ohms

Mention the importance of writing the physical quantities as vectors.​

Answers

Answer:

Knowledge of vectors is important because many quantities used in physics are vectors. If you try to add together vector quantities without taking into account their direction you'll get results that are incorrect.

Explanation:

An example of the importance of vector addition could be the following:

Two cars are involved in a collision. At the time of the collision car A was travelling at 40 mph, car B was travelling at 60 mph. Until I tell you in which directions the cars were travelling you don't know how serious the collision was.

The cars could have been travelling in the same direction, in which case car B crashed into the back of car A, and the relative velocity between them was 20 mph. Or the cars could have been travelling in opposite directions, in which case it was a head on collision with a relative velocity between the cars of 100 mph!

Which of the following statements is true vibrations ?

Answers

Answer:

C. Neither ultrasonic nor infrasonic vibrations can be heard by humans.

Explanation:

The complete question is

Which of the following statements is true of vibrations? A. The frequency of infrasonic vibrations is much too high to be heard by humans. B. Ultrasonic vibrations have a frequency lower than the range for normal hearing. C. Neither ultrasonic nor infrasonic vibrations can be heard by humans. D. Infrasonic vibrations are used in sonar equipment and to detect flaws in steel castings.

Ultrasonic vibrations have frequencies higher than our range of hearing, while infrasonic vibrations have frequencies lower than our range of hearing. Ultrasonic vibrations or sound is used in sonar equipment, and is used for detecting hidden flaws in steel castings and structures. Both infrasonic and ultrasonic fall below and above our normal hearing range respectively, and are only audible to dogs, cats, and some other mammals.

Answer:

Answer is " Two bodies with the same vibration frequency that are placed next to each other will exhibit sympathetic vibrations as one body causes the other to vibrate."

Explanation:

My options were:

A)  Forced vibrations, such as those between a tuning fork and a large cabinet surface, result in a much lower sound than was produced by the original vibrating body.

B)  Resonance occurs as a result of sympathetic vibrations.

C)  A non-vibrating object can begin to vibrate as a result of forced vibrations.

D)  Two bodies with the same vibration frequency that are placed next to each other will exhibit sympathetic vibrations as one body causes the other to vibrate.

A is correct

.

1. Rank the transformers on the basis of their rms secondary voltage. Rank from largest to smallest.
Vp = 240 V; Np = 1000 turns; Ns = 2000 turns
Vp = 480 V; Np = 4000 turns; Ns = 2000 turns
Vp = 480 V; Np = 2000 turns; Ns = 1000 turns
Vp = 120 V; Np = 500 turns; Ns = 2000 turns
Vp = 240 V; Np = 1000 turns; Ns = 500 turns
2. 100 A of rms current is incident on the primary side of each transformer. Rank the transformers on the basis of their rms secondary current. Rank from largest to smallest.
Vp = 240 V; Np = 1000 turns; Ns = 2000 turns
Vp = 480 V; Np = 2000 turns; Ns = 1000 turns
Vp = 240 V; Np = 1000 turns; Ns = 500 turns
Vp = 120 V; Np = 500 turns; Ns = 2000 turns
Vp = 480 V; Np = 4000 turns; Ns = 2000 turns

Answers

Answer:

1. Transformer 3> Transformer 1 and 2 > Transformer 4

2. Transformer 2,3,5 > Transformer 1 > Transformer 4

Explanation:

From;

Vs/Vp = Ns/Np

Where;

Vp= voltage in primary coil

Vs= voltage in secondary coil

Ns= number of turns in secondary coil

Np= number of turns in primary coil.

Vs= Ns×Vp/Np

Vs= 480 ×2000/4000

Vs= 240 V

Vs= 480 ×1000/2000

Vs=240 V

Vs= 120 × 2000/500

Vs= 480 V

Vs= 240 × 500/1000

Vs= 120 V

2. Ns/Np= Ip/Is

Is= Np×Ip/Ns

Is= 1000 × 100/2000

Is= 50 A

Is= 2000 × 100/1000

Is= 200 A

Is= 1000 × 100/500

Is= 200 A

Is= 500 × 100/2000

Is= 25 A

Is= 4000 × 100/2000

Is= 200 A

Did the kinetic frictional coefficient (for the wood/aluminum and felt/aluminum cases) vary with area of contact

Answers

Answer:

Explanation:

Friction is defined as a force which acts at the surface of separation between two objects in contact and tends to oppose motion of one over the other.

While kinetic friction is the force that must be overcome so that a body can move with uniform speed over another.

Hence let consider one of the laws of friction which states that: '' Frictional force is independent of the area of the surfaces in contact.''

The value did not vary with area. This is because when calculating the kinetic fiction, the total contact area is not relevant and only the total weight of the system as well of as the block is put into consideration.

3. What color of laser light shines through a diffraction grating with a line density of 500 lines/mm if the third maxima from the central maxima (m=3) is at an angle of 45°?

Answers

Answer:

Wavelength is 471 nm

Explanation:

Given that,

Lines per unit length of diffraction grating is 500 lines/mm.

The third maxima from the central maxima (m=3) is at an angle of 45°

We need to find the color of laser light shines through a diffraction grating.

The condition for maxima is :

[tex]d\sin\theta=m\lambda[/tex]

d = 1/N, N = number of lines per mm

[tex]\lambda=\dfrac{1}{Nm}\sin\theta\\\\\lambda=\dfrac{10^{-3}}{500\times 3}\sin(45)\\\\\lambda=4.31\times 10^{-7}\\\\\text{or}\\\\\lambda=471\ nm[/tex]

A student wants to create a 6.0V DC battery from a 1.5V DC battery. Can this be done using a transformer alone

Answers

Answer:

Therefore, we need an invert, and a rectifier, along with the transformer to do the job.

Explanation:

A transformer, alone, can not be used to convert a DC voltage to another DC voltage. If we apply a DC voltage to the primary coil of the transformer, it will act as short circuit due to low resistance. It will cause overflow of current through winding, resulting in overheating pf the transformer.

Hence, the transformer only take AC voltage as an input, and converts it to another AC voltage. So, the output voltage of a transformer is also AC voltage.

So, in order to convert a 6 V DC to 1.5 V DC we need an inverter to convert 6 V DC to AC, then a step down transformer to convert it to 1.5 V AC, and finally a rectifier to convert 1.5 V AC to 1.5 V DC.

Therefore, we need an invert, and a rectifier, along with the transformer to do the job.

Two coherent sources of radio waves, A and B, are 5.00 meters apart. Each source emits waves with wavelength 6.00 meters. Consider points along the line connecting the two sources.Required:a. At what distance from source A is there constructive interference between points A and B?b. At what distances from source A is there destructive interference between points A and B?

Answers

Answer:

a

    [tex]z= 2.5 \ m[/tex]

b

   [tex]z = (1 \ m , 4 \ m )[/tex]

Explanation:

From the question we are told that

     Their distance apart is  [tex]d = 5.00 \ m[/tex]

      The  wavelength of each source wave [tex]\lambda = 6.0 \ m[/tex]

Let the distance from source A  where the construct interference occurred be z

Generally the path difference for constructive interference is

              [tex]z - (d-z) = m \lambda[/tex]

Now given that we are considering just the straight line (i.e  points along the line connecting the two sources ) then the order of the maxima m =  0

  so

        [tex]z - (5-z) = 0[/tex]

=>     [tex]2 z - 5 = 0[/tex]

=>     [tex]z= 2.5 \ m[/tex]

Generally the path difference for destructive  interference is

           [tex]|z-(d-z)| = (2m + 1)\frac{\lambda}{2}[/tex]

=>         [tex]|2z - d |= (0 + 1)\frac{\lambda}{2}[/tex]

=>        [tex]|2z - d| =\frac{\lambda}{2}[/tex]

substituting values

          [tex]|2z - 5| =\frac{6}{2}[/tex]

=>      [tex]z = \frac{5 \pm 3}{2}[/tex]

So  

      [tex]z = \frac{5 + 3}{2}[/tex]

      [tex]z = 4\ m[/tex]

and

      [tex]z = \frac{ 5 -3 }{2}[/tex]

=>   [tex]z = 1 \ m[/tex]

=>    [tex]z = (1 \ m , 4 \ m )[/tex]

An engine causes a car to move 10 meters with a force of 100 N. The engine produces 10,000 J of energy. What is the efficiency of this engine?

Answers

Answer:

10%

Explanation:

Efficiency = work done / energy used

e = (10 m × 100 N) / (10,000 J)

e = 0.1

The efficiency is 0.1, or 10%.

It is just as difficult to accelerate a car on a level horizontal surface on the Moon as it is here on Earth because

Answers

Answer:

Mass of the car is independent of gravity

Explanation:

Here, we want to state the reason why even though we have the acceleration due to gravity absent on the moon, it is still difficult to accelerate a car on a level horizontal level on the moon.

The answer to this is that the mass of the car that we want to accelerate is independent of gravity.

Had it been that gravity has an effect on the mass of the said car, then we might conclude that it will not be difficult to accelerate the car on a horizontal surface on the moon.

But due to the fact that gravity has no effect on the mass of the car to be accelerated, then the problem we have on earth with accelerating the car is the same problem we will have on the moon if we try to accelerate the car on a horizontal level surface.

Describe and name the different types of collision. In which are the linear momentum and kinetic energy conserved

Answers

Answer:

1. Elastic collision

2. Inelastic collision    

Explanation:

Elastic collision: collision is said to be elastic if total kinetic energy is not conserved and if there is a rebound after collision

the collision is described by the equation bellow

[tex]m1U1+ m2U2= m1V1+m2V2[/tex]

Inelastic collision: this type of collision occurs when the total kinetic energy of a body is conserved or when the bodies sticks together and move with a common velocity

the collision is described by the equation bellow

[tex]m1U1+ m2U2= V(m1+m2)[/tex]

Other Questions
The Marketing Control Statement is a valuable statement for marketers because it only utilizes costs that the marketer can control. True False NEEEEDDDD ASSAAAAPPPPP NEED ANSWER NOWWWW While your hands are on home row, your left hand rests lightly on _____. z x c v j k l ; q w e r a s d f A formula developed to project a pattern of periodic income. Income models can be applied to level income with no change in value, level income with changing value, income and value that change by fixed amounts per period (straight-line), income and value that change at a constant ratio (exponential-curve), and variable or irregular income with changing value (True/False) What were different reasons that people came to the colonies in NorthAmerica? Which of the following is true? Group of answer choices The Bulge of Africa is in the south, the Horn is in the north. The Bulge of Africa is in the west, the Horn is in the east. The Bulge of Africa is in the north, the Horn is in the south. The Bulge of Africa is a desert area and the Horn is tropical. The graph below shows the quadratic function f, and the table below shows the quadratic function g.x-1012345g(x)138545813Which statement is true?A. The functions f and g have the same axis of symmetry and the same y-intercept.B. The functions f and g have different axes of symmetry and different y-intercepts.C. The functions f and g have the same axis of symmetry, and the y-intercept of f is greater than the y-intercept of g.D. The functions f and g have the same axis of symmetry, and the y-intercept of f is less than the y-intercept of g. On Jan. 5, a customer returned merchandise that has been purchased earlier on credit. The original sale was for $500 and the cost to the seller was $150.What is the required journal entry to record the return on the seller books? Assume all merchandise can be resold to another customer. A club has 16 members, included Mary and Peter. If two representative arerandomly selected from those members, find the probability that(d) Mary or Peter is chosen. A website developer wished to analyze the clicks per day on their newly updated website. Let the mean number of clicks per day be . If the website developer wants to know if the number of clicks per day is different than 200 clicks a day, on average, what are the null and alternative hypotheses? On January 31, 2021, B Corp. issued $650,000 face value, 11% bonds for $650,000 cash. The bonds are dated December 31, 2020, and mature on December 31, 2030. Interest will be paid semiannually on June 30 and December 31. What amount of accrued interest payable should B report in its September 30, 2021, balance sheet Which rule should be followed to stay safe online?O Keep inappropriate messages private.O Avoid sharing photos with anyone online.O Keep screen names private.Ask an adult for permission to download. Pleaseeeee help me. When a rabbit eats a plant, nutrients from theplant become available to the tissues of therabbit. During this process, some of the energyfrom these nutrients is lost and the energybecomes heat and unavailable chemical energy.This energy loss partly explains why the totalenergy is greater inA. predator populations than in scavengerpopulations.B.consumer populations than in producerpopulations.C. producer populations than in consumerpopulations.D. predator populations than in prey populations, 1/2x+1/3y=21/3x+1/2y=13/6 (x is not equal to 0, y is not equal to 0) by substitution method, step by step pls write 5-6 lines of vayayam ke labh in hindi pls helpsorry in my phone there is no hindi option when i press ask question If you wanted to enjoy direct sun on Fogo Island in the tropical West African country of Cape Verde, which date would be best A poker hand consisting of 7 cards is dealt from a standard deck of 52 cards. Find the probability that the hand contains exactly 3 face cards. Leave your answer as a reduced fraction. The projected worth (in millions of dollars) of a large company is modeled by the equation w = 221(1.09) t. The variable t represents the number of years since 2000. What is the projected annual percent of growth, and what should the company be worth in 2008? A. 9%; $440.36 million B. 19%; $479.99 million C. 9%; $404.00 million D. 19%; $240.89 million The graphs below have the same shape. Complete the equation of the bluegraph. Enter exponents using the caret (; for example, enter x2 as x^2. Evaluate the expression 52 + 2x when x = 5. Choose the phrase below that describes the resulting number.