Answers
Following the definition of the center of mass, "In physics, the center of mass of a distribution of mass in space is the unique point where the weighted relative position of the distributed mass sums to zero."
(see explanation below)
Related Questions
True or false: Increasing the Young’s modulus of a beam in bending will cause it to deflect less.
Answers
Answer:
false?
Explanation:
The higher the modulus, the more stress is needed to create the same amount of strain; an idealized rigid body would have an infinite Young's modulus.
Answer:
I think the answer is False.
What would you expect to happen to the velocity of the bobber if the mass of the washers in the cylinder remained the same and the radius was doubled?
Answers
Answer:
The velocity becomes [tex]v\sqrt 2[/tex].
Explanation:
The force acting on the bobber is centripetal force.
The centripetal force is given by
[tex]F =\frac{mv^2}{r}[/tex]
when mass remains same, radius is doubled and the force is same, so the velocity is v'.
[tex]F =\frac{mv^2}{r}=\frac{mv'^2}{2r}\\\\v'=v\sqrt 2[/tex]
The distance between the two object is fixed at 5.0 m. The uncertainty distance measurement is? The percentage error in the distance is?
Answers
The mass of a hot-air balloon and its occupants is 381 kg (excluding the hot air inside the balloon). The air outside the balloon has a pressure of 1.01 x 105 Pa and a density of 1.29 kg/m3. To lift off, the air inside the balloon is heated. The volume of the heated balloon is 480 m3. The pressure of the heated air remains the same as that of the outside air. To what temperature in kelvins must the air be heated so that the balloon just lifts off
Answers
Answer:
In order to lift off the ground, the air in the balloon must be heated to 710.26 K
Explanation:
Given the data in the question;
P = 1.01 × 10⁵ Pa
V = 480 m³
ρ = 1.29 kg/m³
M = 381 kg
we know that; R = 8.31 J/mol.K and the molecular mass of air μ = 29 × 10⁻³ kg/mol
let F represent the force acting upward.
Now in a condition where the hot air balloon is just about to take off;
F - Mg - m[tex]_g[/tex]g = 0
where M is the mass of the balloon and its occupants, m[tex]_g[/tex] is the mass of the hot gas inside the balloon.
the force acting upward F = Vρg
so
Vρg - Mg - m[tex]_g[/tex]g = 0
solve for m[tex]_g[/tex]
m[tex]_g[/tex] = ( Vρg - Mg ) / g
m[tex]_g[/tex] = Vρg/g - Mg/g
m[tex]_g[/tex] = ρV - M ------- let this be equation 1
Now, from the ideal gas law, PV = nRT
we know that number of moles n = m[tex]_g[/tex] / μ
where μ is the molecular mass of air
so
PV = (m[tex]_g[/tex]/μ)RT
solve for T
μPV = m[tex]_g[/tex]RT
T = μPV / m[tex]_g[/tex]R -------- let this be equation 2
from equation 1 and 2
T = μPV / (ρV - M)R
so we substitute in our values;
P = 1.01 × 10⁵ Pa
V = 480 m³
ρ = 1.29 kg/m³
M = 381 kg
we know that; R = 8.31 J/mol.K and the molecular mass of air μ = 29 × 10⁻³ kg/mol
T = [ (29 × 10⁻³) × (1.01 × 10⁵) × 480 ] / [ (( 1.29 × 480 ) - 381)8.31 ]
T = 1405920 / 1979.442
T = 710.26 K
Therefore, In order to lift off the ground, the air in the balloon must be heated to 710.26 K
The temperature required for the air to be heated is 710.26 K.
Given data:
The mass of a hot air-balloon is, m = 381 kg.
The pressure of air outside the balloon is, [tex]P = 1.01 \times 10^{5} \;\rm Pa[/tex].
The density of air is, [tex]\rho = 1.29 \;\rm kg/m^{3}[/tex].
The volume of heated balloon is, [tex]V = 480 \;\rm m^{3}[/tex].
The condition where the hot air balloon is just about to take off is as follows:
[tex]F-mg - m'g =0[/tex]
Here,
m' is the mass of hot gas inside the balloon and g is the gravitational acceleration and F is the force acting on the balloon in upward direction. And its value is,
[tex]F = V \times \rho \times g[/tex]
Solving as,
[tex](V \times \rho \times g)-mg - m'g =0\\\\ m'=(V \rho )-m[/tex]
Now, apply the ideal gas law as,
PV = nRT
here, R is the universal gas constant and n is the number of moles and its value is,
[tex]n=\dfrac{m'}{M}[/tex]
M is the molecular mass of gas. Solving as,
[tex]PV = \dfrac{m'}{M} \times R \times T\\\\\\T=\dfrac{P \times V\times M}{m'R}\\\\\\T=\dfrac{P \times V\times M}{(V \rho - m)R}[/tex]
Since, the standard value for the molecular mass of air is, [tex]M = 29 \times 10^{-3} \;\rm kg/mol[/tex]. Then solve for the temperature as,
[tex]T=\dfrac{(1.01 \times 10^{5}) \times 480\times 381}{(480 \times (1.29) - 381)8.31}\\\\\\T = 710.26 \;\rm K[/tex]
Thus, we can conclude that the temperature required for the air to be heated is 710.26 K.
Learn more about the ideal gas equation here:
https://brainly.com/question/18518493
Can an electron be diffracted? Can it exhibit interference?
Answers
Answer:
Yeah, it can be diffracted. Though it depends on a diffracting medium.
It must have some magnetic fields .
Forexample; X-ray diffraction where electrons are diffracted to the target filament.
Suppose that 2 J of work is needed to stretch a spring from its natural length of 34 cm to a length of 46 cm. (a) How much work is needed to stretch the spring from 36 cm to 41 cm
Answers
Answer:
0.83 J of work
Explanation:
2 J of work is required to stretch a spring from 34cm to 46cm
So that is 12cm stretched with 2 J of work
We can make that 6cm for 1 J of work
So, we need the find the work for stretching 36cm to 41cm
Which is 5cm
So, What is the work required to stretch 5cm?
1 J of work for 6cm
x work for 5cm
So, by proportion method
1 : 6 :: x : 5
6 * x = 1 * 5
6x = 5
x = 5/6
= 0.83
So to stretch 36cm to 41cm we need 0.83 J of work
• Explain how sound travels
Answers
Sound is a type of energy made by vibrations. These vibrations create sound waves which move through mediums such as air, water and wood. When an object vibrates, it causes movement in the particles of the medium. This movement is called sound waves, and it keeps going until the particles run out of energy.
Sound is a type of energy made by vibrations. These vibrations create sound waves which move through mediums such as air, water and wood. When an object vibrates, it causes movement in the particles of the medium. This movement is called sound waves, and it keeps going until the particles run out of energy.
Put the balloon near (BUT NOT TOUCHING) the wall. Leave about as much space as the width of your pinky finger between the balloon and wall. Does the balloon move, if so which way
Answers
Answer:
Move towards the wall.
Explanation:
When the balloon is kept near to the wall not touching the wall, there is a force of electrostatic attraction so that the balloon moves towards the wall and stick to it.
As there is some charge on the balloon and the wall is uncharged so the force is there due to which the balloon moves towards the wall.
The pan flute is a musical instrument consisting of a number of closed-end tubes of different lengths. When the musician blows over the open ends, each tube plays a different note. The longest pipe is 0.31 m long.
What is the frequency of the note it plays? Assume room temperature of 20∘C.
Answers
Answer:
f = 276.6 Hz
Explanation:
This musical instrument can be approximated to a tube system where each tube has one end open and the other closed.
In the closed part there is a node and in the open part a belly or antinode. Therefore the wavelength is
L = λ/ 4
speed is related to wavelength and frequency
v = λ f
λ = v / f
we substitute
L = v / 4f
f = v / 4L
the speed of sound at 20ºC is
v = 343 m / s
let's calculate
f = [tex]\frac{343 }{4 \ 0.31}[/tex]
f = 276.6 Hz
A 0.40-kg mass attached to the end of a string swings in a vertical circle having a radius of 1.8 m. At an instant when the string makes an angle of 40 degrees below the horizontal, the speed of the mass is 5.0 m/s. What is the magnitude of the tension in the string at this instant
Answers
Answer:
[tex]T=8.1N[/tex]
Explanation:
From the question we are told that:
Mass m=0.40
Radius r=1.8m
Angle Beneath the Horizontal \theta =40 \textdegree
Speed v=5.0m/s
The Tension Angle
[tex]\alpha=90-\theta\\\\\alpha=90-40[/tex]
[tex]\alpha=50 \textdegree[/tex]
Generally the equation for Tension is is mathematically given by
[tex]T=\frac{mv^2}{r}+mgcos \alpha[/tex]
[tex]T=\frac{0.40*5^2}{1.8}+0.40*5cos50[/tex]
[tex]T=8.1N[/tex]
A long, current-carrying solenoid with an air core has 1550 turns per meter of length and a radius of 0.0240 m. A coil of 200 turns is wrapped tightly around the outside of the solenoid, so it has virtually the same radius as the solenoid. What is the mutual inductance of this system
Answers
Answer:
[tex]M=7.05*10^{-4}[/tex]
Explanation:
From the question we are told that:
Coil one turns N_1=1550 Turns/m
Radius [tex]r=0.0240m[/tex]
Turns 2 [tex]N_2=200N[/tex]
Generally the equation for area is mathematically given by
[tex]A=\pi*r^2[/tex]
[tex]A=\pi*0.024^2[/tex]
[tex]A=\1.81*10^{-3} m^2[/tex]
Therefore
The mutual inductance of this system is
[tex]M=\mu*N_1*N_2*A[/tex]
[tex]M=(4 \pi*10^{-7})*1550*200*1.81*10^{-3}[/tex]
[tex]M=7.05*10^{-4}[/tex]
Select the only true statement:
A)A beam in bending experiences tensile stresses on one side and compressive stresses on the other side.
B)A beam in bending experiences tensile stresses along the beam center and compressive stresses along the beam’s edges.
C)A beam in bending experiences only compressive stresses.
D)A beam in bending experiences only tensile stresses.
Answers
Answer:
Sorry I dont know this answer sorry
Explain how the gravitational force between the earth and the sun changes as the earth moves from position A to B as shown in the figure. Sun Earth at position B Earth at position A
Answers
Answer:
The distance between sun & Earth at position A is less than the earth at position B. The gravitational force of two bodies is inversely proportional to the square of the distance. So At position A gravitational force is more & it decreases as it rotate towards position B.
A possible means for making an airplane invisible to radar is to coat the plane with an antireflective polymer. If radar waves have a wavelength of 3.00 cm and the index of refraction of the polymer is n = 1.50, how thick would you make the coating?
Answers
Answer:
[tex]t=0.50cm[/tex]
Explanation:
From the question we are told that:
Wavelength [tex]\lamda=3c[/tex]m
Refraction Index [tex]n=1.50[/tex]
Generally the equation for Destructive interference for Normal incidence is mathematically given by
[tex]2nt=m(\frac{1}{2})\lambda[/tex]
Since Minimum Thickness occurs at
At [tex]m=0[/tex]
Therefore
[tex]t=\frac{\lambda}{2}[/tex]
[tex]t=\frac{3}{4(1.50)}[/tex]
[tex]t=0.50cm[/tex]
An infinite plane lies in the yz-plane and it has a uniform surface charge density.
The electric field at a distance x from the plane
a.) decreases as 1/x^2
b.) increases linearly with x
c.) is undertermined
d.) decreases linearly with x
e.) is constant and does not depend on x
Answers
Answer:
So the correct answer is letter e)
Explanation:
The electric field of an infinite yz-plane with a uniform surface charge density (σ) is given by:
[tex]E=\frac{\sigma }{2\epsilon_{0}}[/tex]
Where ε₀ is the electric permitivity.
As we see, this electric field does not depend on distance, so the correct answer is letter e)
I hope it helps you!
A 0.20 kg mass on a horizontal spring is pulled back a certain distance and released. The maximum speed of the mass is measured to be 0.30 m/s. If, instead, a 0.40 kg mass were used in this same experiment, choose the correct value for the maximum speed.
a. 0.40 m/s.
b. 0.20 m/s.
c. 0.28 m/s.
d. 0.14 m/s.
e. 0.10 m/s.
Answers
Answer:
b. 0.20 m/s.
Explanation:
Given;
initial mass, m = 0.2 kg
maximum speed, v = 0.3 m/s
The total energy of the spring at the given maximum speed is calculated as;
K.E = ¹/₂mv²
K.E = 0.5 x 0.2 x 0.3²
K.E = 0.009 J
If the mass is changed to 0.4 kg
¹/₂mv² = K.E
mv² = 2K.E
[tex]v = \sqrt{\frac{2K.E}{m} } \\\\v = \sqrt{\frac{2\times 0.009}{0.4} } \\\\v = 0.21 \ m/s\\\\v \approx 0.20 \ m/s[/tex]
Therefore, the maximum speed is 0.20 m/s
Two distinct systems have the same amount of stored internal energy. 500 J are added by heat to the first system and 300 J are added by heat to the second system. What will be the change in internal energy of the first system if it does 200 J of work? How much work will the second system have to do in order to have the same internal energy?
Answers
Answer:
The change in the internal energy of the first system is 300 J
The second system will do zero work in order to have the same internal energy.
Explanation:
Given;
heat added to the first system, Q₁ = 500 J
heat added to the second system, Q₂ = 300 J
work done by the first system, W₁ = 200 J
The change in the internal energy of the system is given by the first law of thermodynamics;
ΔU = Q - W
where;
ΔU is the change in internal energy of the system
The change in the internal energy of the first system is calculated as;
ΔU₁ = Q₁ - W₁
ΔU₁ = 500 J - 200 J
ΔU₁ = = 300 J
The work done by the second system to have the same internal energy with the first.
ΔU₁ = Q₂ - W₂
W₂ = Q₂ - ΔU₁
W₂ = 300 J - 300 J
W₂ = 0
The second system will do zero work in order to have the same internal energy.
The thermal efficiency (in %) of a system that undergoes a power cycle while receiving 1000 kJ of energy by heat transfer from a hot reservoir at 1000 K and discharging 500 kJ of energy by heat transfer to a cold reservoir at 400 K is:
Answers
Answer:
η = 0.5 = 50%
Explanation:
The efficiency of the power cycle is given by the following formula:
[tex]\eta = \frac{W}{Q_1}\\\\\eta = \frac{Q_1-Q_2}{Q_1}[/tex]
where,
where,
η = efficiency = ?
Q₁ = heat received from hot reservoir = 1000 KJ
Q₂ = heat discharged to cold reservoir = 500 KJ
Therefore,
[tex]\eta = \frac{1000\ KJ-500\ KJ}{1000\ KJ}[/tex]
η = 0.5 = 50%
If you tethered a space station to the earth by a long cable, you could get to space in an elevator that rides up the cable much simpler and cheaper than riding to space on a rocket. There's one big problem, however: There is no way to create a cable that is long enough. The cable would need to reach 36,000 km upward, to the height where a satellite orbits at the same speed as the earth rotates; a cable this long made of ordinary materials couldn't even support its own weight. Consider a steel cable suspended from a point high above the earth. The stress in the cable is highest at the top; it must support the weight of cable below it.
What is the greatest length the cable could have without failing?
Answers
Answer:
[tex]l=12916.5m[/tex]
Explanation:
Distance [tex]d=3600km[/tex]
Since
Density of steel [tex]\rho=7900kg/m^3[/tex]
Stress of steel [tex]\mu= 1*10^9[/tex]
Generally the equation for Stress on Cable is mathematically given by
[tex]S=\frac{F}{A}[/tex]
[tex]S=\frac{\rho Alg}{A}[/tex]
Therefore
[tex]l=\frac{s}{\rhog}[/tex]
[tex]l=\frac{ 1*10^9}{7900kg/m^3*9.8}[/tex]
[tex]l=12916.5m[/tex]
Nhiệt dung riêng của một chất là ?
Answers
Answer:
enchantment table language
Explanation:
If you double the current in a long straight wire, the magnetic field at a fixed point will... be cut in half. triple. double. quadruple.
Answers
Answer:
the magnetic field must double
Explanation:
For this exercise we use Ampere's law
∫ B . ds = μ₀ I
Where the bold indicate vectors
With this expression we can see that if we double the current, keeping the same trajectory, the magnetic field must double
You throw a Frisbee of mass m and radius r so that it is spinning about a horizontal axis perpendicular to the plane of the Frisbee. Ignoring air resistance, the torque exerted about its center of mass by gravity is: __________
a. 0.
b. mgr
c. 2mgr
d. a function of the angular velocity.
e. small at first, then increasing as the Frisbee loses the torque given it by your hand.
Answers
Answer:
the correct answer is a
Explanation:
The torque is
τ = F x r
where the bold letters indicate vectors, in this case the vector of the center of mass is perpendicular to the weight of the body
τ = mg r
in body weight it is applied at the point of the center of mass, therefore as the distance of the force from the axis of rotation (center of amas) is zero, the die is zero
the correct answer is a
A building is being knocked down with a wrecking ball, which is a big metal sphere that swings on a 15-m-long cable. You are (unwisely!) standing directly beneath the point from which the wrecking ball is hung when you notice that the ball has just been released and is swinging directly toward you. How much time do you have to move out of the way? answer in seconds.
Answers
Answer:
Time to move out of the way = 1.74 s
Explanation:
Time to move out of the way is one fourth of period = 6.95/4 = 1.74 seconds.
Time to move out of the way = 1.74 s
Place each description under the correct theory
Gravity is an attractive force.
Universal Law of Gravitation
General Theory of Relativity
Mass and distance affect force.
Time and space are absolute,
Time and space are relative.
Gravity is due to space-time curving.
Mass affects space-time curving.
Answers
Answer:
1) Law of Universal Gravitation Gravity is an attractive force
5) General relativity Gravity is due to the curvature of spacetime
Explanation:
In this exercise you are asked to relate the correct theory and its explanation
Theory Explanation
1) Law of Universal Gravitation Gravity is an attractive force
2) Law of universal gravitation Mass and distance affect force
3) Classical mechanics time and space are absolute
4) Special relativity Time and space are relative
5) General relativity Gravity is due to the curvature of
spacetime
6) General relativity Mass affects the curvature of space - time
Answer:
Explanation:
edge2022
The mass is released from the top of the incline and slides down the incline. The maximum velocity (taken the instant before the mass reaches the bottom of the incline) is 1.06 m/s. What is the kinetic energy at that time
Answers
Answer:
0.28 J
Explanation:
Let the mass of the object is 0.5 kg
The maximum velocity of the object is 1.06 m/s.
We need to find the kinetic energy at that time. It is given by :
[tex]K=\dfrac{1}{2}mv^2\\\\=\dfrac{1}{2}\times 0.5\times (1.06)^2\\\\K=0.28\ J[/tex]
So, the required kinetic energy is equal to 0.28 J.
Question 4 of 5
How can the Fitness Logs help you in this class?
O A. They can't; the Fitness Logs are only useful to your teacher.
B. They show your parents how much you're learning.
C. They let you keep track of your thoughts, feelings, and progress.
D. They help you evaluate yourself for your final grade.
SUBMIT
Answers
Answer:
C is the right answer
Explanation:
fitness logs is a great way to track your progress. You can easily look back and see how you have progressed over time. In addition, it can help you plan and prepare for future workouts, as well as identify patterns of what seems to work well for you and when you have the most success
hope it was useful for you
3. If you change the resistance of the resistor:
a. How does the current through the circuit change? (answer, explain, evidence)
b. How does the voltage of the battery change? (answer, explain, evidence)
Answers
Answer:
Explanation:
Changing the resistance of a resistor means the resistance is either increased or decreased.
a. When the resistance of the resistor is increased, the value of current flowing through the circuit decreases.
Example: given voltage of 6V, and a resistance of 30 Ohm's. The value of current flowing in the circuit is;
V = IR
6 = I x 30
I = 0.2 A
If the resistance is changed to 50 Ohm's, then:
I = 0.12 A
(ii) When the resistance of the resistor is decreased, the value of the current flowing through the circuit increases.
In the previous example, if the resistance is changed to 5 Ohm's, then:
V = IR
6 = I x 5
I = 1.2 A
(b) The voltage of the battery does not change since it is directly proportional to the current flowing through the circuit. Consider the examples stated above.
Need help! Need help! Need help! Need help! Need help! Need help!
Answers
Answer:
i can help you i know this answer
Answer: the side two are 50 then the other two are 140 i thank
Explanation:
Write a short note of the following
a) Reflection
b) Refraction
c) Diffraction
Answers
Answer:
a) Light that passes through the floor to reveal yourself (not shadow).
b) 2 rays of light that bounce between 2 transparent media.
c) I don't know what is Diffraction?
Two identical cars, each traveling at 16 m>s, slam into a concrete wall and come to rest. In car A the air bag does not deploy and the driver hits the steering wheel; in car B the driver contacts the deployed air bag. (a) Is the impulse delivered by the steering wheel to driver A greater than, less than, or equal to the impulse delivered by the air bag to driver B
Answers
Answer:
I = - m 16 the two impulses are the same,
Explanation:
The impulse is given by the relationship
I = Δp
I = p_f - p₀
in this case the final velocity is zero therefore p_f = 0
I = -p₀
For driver A the steering wheel impulse is
I = - m v₀
I = - m 16
For driver B, the airbag gives an impulse
I = - m 16
We can see that the two impulses are the same, the difference is that in the air bag more time is used to give this impulse therefore the force on the driver is less
