Answer:
c- ability to undergo chemical reaction
In practice, the second law of thermodynamics means that:
a. Systems move from ordered behavior to more random behavior.
b. Systems move from random behavior to more ordered behavior.
c. Systems move between ordered and random behavior patterns based on temperature.
d. Systems are constantly striving to reach equilibrium.
Answer:
Systems move from ordered behavior to more random behavior.
Explanation:
Entropy refers to the degree of disorderliness in a system. The second law of thermodynamics can be restated in terms of entropy as follows; “any spontaneous process in any isolated system always results in an increase in the entropy of that system.''(science direct)
According to this law, systems tend towards a more disorderly behaviour (increase in entropy) hence the answer given above.
P.1 is a variant of SARS-CoV2. This is the so-called "Brazil variant". It has the amino acid the substitution N501Y in the spike protein on the virus surface. In cellular fluids at ~pH 7 the wild type spike protein has a net negative charge. This substitution will make the spike protein
more negative
less hydrophobic
able to absorb move UV light
less negative
There are various variants of Cov id virus. The Brazilian variant P also known as Gamma variant is the third variant of the original SARS-CoV2.
The correct answer is more negative
This variant has raised concerns since it has ability to spread more quickly then previous variants and this is more negative variant.
It is assumed that Cov id variant Gamma and Delta has ability to absorb move UV light but this is not proved yet and research is underway.
Learn more at https://brainly.com/question/24319270
Nitric acid can be formed in two steps from the atmospheric gases nitrogen and oxygen, plus hydrogen prepared by reforming natural gas. In the first step, nitrogen and hydrogen react to form ammonia: N2 (g) + 3H2 (g) â 2NH3 (g) =ÎHâ92.kJ In the second step, ammonia and oxygen react to form nitric acid and water:
NH3 (g) + 2O2 (g) â HNO3 (g) + H2O (g) =ÎHâ330.kJ
Required:
Calculate the net change in enthalpy for the formation of one mole of nitric acid from nitrogen, hydrogen and oxygen from these reactions.
Answer:
-376 kJ
Explanation:
The first step equation:
[tex]\mathsf{N_{2(g)} + 3H_2{(g)} \to 2NH_3{(g)} \ \ \ \Delta H = -92\ kJ}[/tex] ---- (1)
The second step equation:
[tex]\mathsf{NH_{3(g)} + 2O_2{(g)} \to HNO_3{(g)} +H_2O_{(g)} \ \ \ \Delta H = -330\ kJ}[/tex] ---- (2)
To determine the enthalpy of formation for 1 mole of HNO₃ (nitric acid), we have the following.
From the above equations; let multiply equation (1) by 1 and equation (2) by 2.
[tex]\mathsf{N_{2(g)} + 3H_2{(g)} \to 2NH_3{(g)} \ \ \ \Delta H = -92\ kJ}[/tex] ---- (3)
[tex]\mathsf{2NH_{3(g)} + 4O_2{(g)} \to 2HNO_3{(g)} +2H_2O_{(g)} \ \ \ \Delta H = 2(-330)\ kJ}[/tex] ----- (4)
adding the above two equations, we have:
[tex]\mathsf{N_{2(g)} + 3H_2{(g)}+ 2NH_{3(g)} + 4O_{2(g)} \to 2HNO_{3(g)} + 2NH_3{(g)} +2H_2O_{(g)} \ \ \ \Delta H = (-660 \ kJ -92\ kJ)}[/tex][tex]\mathsf{N_{2(g)} + 3H_2{(g)} + 4O_{2(g)} \to 2HNO_{3(g)} +2H_2O_{(g)} \ \ \ \Delta H = (-752 \ kJ)}[/tex]
Now, from the recent equation, we have:
2 moles of nitric acid = -752 kJ
∴
1 mole of nitric acid will be: = (1 mole × (-752 kJ)) ÷ 2 moles
1 mole of nitric acid will be: = -376 kJ
Tech A says that hydrocarbons are a result of complete combustion. Tech B says that a catalytic converter creates a chemical reaction, changing carbon monoxide and hydrocarbons to water and carbon dioxide. Who is correct
Answer:
Neither Tech A nor B is correct
Explanation:
Combustion is a chemical reaction that occurs when a chemical molecule(s) interacts quickly with oxygen and produces heat.
When hydrocarbon undergoes a complete combustion reaction, they produce water and CO2.
Tech B is also incorrect because the main purpose of a catalytic converter is to accelerate and speed up the chemical reaction rates, Hence, they are not involved in chemical reaction formation. Catalytic converters are utilized as a control device in exhaust emission to lessen the effect of toxic gas fumes.
Given the equation representing a nuclear reaction in
which X represents a nuclide:
232Th → He + x
Which nuclide is represented by X?
A) 236
B) 228
Ra
SS
C) 236
Ra
92
U
92
D) 228
.
Ss U
The nuclide represented as X is thorium and this is an alpha decay.
The equation shown represents an alpha decay. In an alpha decay, an alpha particle is given off.
The atomic number of the parent nuclide is greater than that of the daughter nuclide by two units while the mass number of the parent is greater than that of the daughter nuclide by four units.
Hence the equation occurs as follows;
[tex]\frac{232}{92} Th ------> \frac{228}{88} Ra + He[/tex]
https://brainly.com/question/14081292
GM 2 all ,What is an atom define it .Good Day
Answer:
An atom is the smallest particle of an element that can take part in chemical reaction.
Explanation:
hope it will help u Amri
#19.
An unknown sample weighs 45.2 g and takes 58.2 kJ to vaporize. What is
its heat of vaporization?
What would be the name of this compound?
Answer:
2,3 Dimethyl hexane
Explanation:
First, start the count from which side is given the CH3 smallest number
first; the longest carbon chain in this compound is 6
and you don't have any double and triple bonds or functional groups so it is Hexane
you start to count from the right side to give the branch molecules the smallest number ..
CH3 = methyl
and you have 2 methyl in this compound ..
and 2 mean you must write ( Di )
you write the name in this way
2,3 Dimethyl hexane
hope this helps you.
stay safe ...
What process occurs during the corrosion of iron?
Answers
A.
Iron is oxidized.
B.
Iron is reduced.
C.
Iron (III) is oxidized.
D.
Iron (III) is reduced.
Answer:
A
Explanation:
The iron corrodes so it oxidized
In the reoxidation of QH2 by purified ubiquinone-cytochrome c reductase (Complex III) from heart muscle, the overall stoichiometry of the reaction requires 2 mol of cytochrome c per mole of QH2 because:
Answer: Options related to your question is missing below are the missing options
a. cytochrome c is a one-electron acceptor, whereas QH2 is a two-electron donor.
b. cytochrome c is a two-electron acceptor, whereas QH2 is a one-electron donor.
c. cytochrome c is water soluble and operates between the inner and outer mitochondrial membranes
d. heart muscle has a high rate of oxidative metabolism, and therefore requires twice as much cytochrome c as QH2 for electron transfer to proceed normally.
e. two molecules of cytochrome c must first combine physically before they are catalytically active.
answer:
cytochrome c is a one-electron acceptor, whereas QH2 is a two-electron donor. ( A )
Explanation:
The overall stoichiometry of the reaction requires 2 mol of cytochrome per mole of QH2 because a cytochrome is simply a one-electron acceptor while QH2 is not a one-electron donor ( i.e. it is a two-electron donor )
An electron donor in a reaction is considered a reducing agent because it donates its electrons to another compound thereby self oxidizing itself in the process.
does anyone know how to solve this and what the answer would be?
Dynamic equilibrium is showed at the point at which solid liquid and gas intersect.
At the point at which solid liquid and gas intersect represents a system that shows dynamic equilibrium. There is equal amount of reactants and products at the point of dynamic equilibrium because the transition of substances occur between the reactants and products at equal rates, means that there is no net change. Reactants and products are formed at the rate that no change occur in their concentration.
https://brainly.com/question/24310467
A sample of Kr gas is observed to effuse through a pourous barrier in 8.15 minutes. Under the same conditions, the same number of moles of an unknown gas requires 4.53 minutes to effuse through the same barrier. The molar mass of the unknown gas is ____________ g/mol.
Answer:
25.88 g/mol
Explanation:
Graham's law is a famous law which states that the diffusion rate or the effusion rate of any gas varies inversely to the square root of the molecular weight the gas.
So from Graham's law, we have,
[tex]$\frac{\text{time}}{M^{1/2}}=\text{constant}$[/tex]
Using the sample of Kr gas having M = 83.8
[tex]$\frac{8.15}{(83.8)^{0.5}}= \frac{4.53}{M^{0.5}}$[/tex]
[tex]$M^{0.5}= 5.088$[/tex]
M = 25.88 g/mol
I need to know what is the median of the data
Answer:
The median is also the number that is halfway into the set. To find the median, the data should be arranged in order from least to greatest. If there is an even number of items in the data set, then the median is found by taking the mean (average) of the two middlemost numbers.
I hope it helps
A/An is a type of blood cell that's also called a red blood cell. a) Jeukocyte O b) thrombocyte c) plasma d) erythrocyte
Answer:
option a
Explanation:
pls mark me as brainliest
How does distance between two objects affect their gravitational force? (2 points)
a
Force increases as distance increases.
b
Force decreases as distance increases.
c
Force decreases as distance decreases.
d
Force is not related to distance.
Answer:
Option B: as the distance between the objects increases the Force of gravity decreases
Lead of mass 0.75kg is heated from 21°c to its melting point and continues to be heated unit it has all melted. Calculate how much energy is supplied to the lead. [Melting point of lead 372.5°c specific latent heat of fusion of lead = 23000 Jkg 'k ']
Answer:
65.5J
Explanation:
ML=Q
ML=MC(change in temperature)
0.75 X 23000 =0.75 X 351 X C
C= 65.5J
The energy supplied to the lead to melt from 21°c to its melting point is 51521 Joules.
What is the specific heat capacity?Specific heat is the amount of heat energy supplied to change the temperature of one unit mass of a substance by 1 °C. The SI unit of the specific heat capacity of a substance is J/Kg.
The mathematical expression for the specific heat capacity can be written as:
Q = mCΔT Where C is the specific heat of the substance.
The specific heat capacity depends upon the starting temperature and is an intensive characteristic of the material.
Given, the melting point of the lead T₂ = 327.5° C
The initial temperature of the lead, T₁ = 21° C
The latent heat of the lead given, L = 230000 J/Kg K
The specific heat of the lead, C = 130 J/Kg K
The heat required to melt the lead from 12°C to 327.5 °C is :
Q = m× [C × (T₂ - T₁) + L ]
Q = 0.75 × [0.130 (327.5 - 21) + 23000]
Q = 51521 J
Learn more about specific heat, here:
brainly.com/question/11297584
#SPJ5
If the balance were not tared prior to weighing out the KHP.... how would you expect this to affect the molarity of NaOH calculated? What type of error is this?
Answer:
Following are the response to the given question:
Explanation:
In the given scenario, When the balance has never been tainted before the KHP is weighted, which can affect the molar concentration of NaOH because its molarity is directly proportional to the weight including its substance. In this question it is the mistake is systemic because it may be corrected by modifying balancing parameters.
How many neutrons does Carbon- 14 and Carbon -15 have? *
Answer: 8 for both
Explanation:
When equal moles of an acid and a base are mixed, after reaction the two are compounds are said to be at the _______________. Select one: Indicator point Stoichiometric point Equilibrium point End point
Answer:
when equal moles of an acid and base are mixed,after reaction the two are compounds are said to be at the Equivalent point.
The sample concentration was measured at 50mg/ml. The loading concentration needs to be 10mg/ml. The final volume needs to be 25ul. What is the volume of sample needed and the amount of buffer needed to reach 25ul
Answer:
a) [tex]V_1=5ul[/tex]
b) [tex]v=20ul[/tex]
Explanation:
From the question we are told that:
initial Concentration [tex]C_1=50mg/ml[/tex]
Final Concentration [tex]C_2=10mg/ml[/tex]
Final volume needs [tex]V_2 =25ul[/tex]
Generally the equation for Volume is mathematically given by
[tex]C_1V_1=C_2V_2[/tex]
[tex]V_1=\frac{C_1V_1}{C_2}[/tex]
[tex]V_1=\frac{10*25}{50}[/tex]
[tex]V_1=5ul[/tex]
Therefore
The volume of buffer needed is
[tex]v=V_2-V_1\\\\v=25-5[/tex]
[tex]v=20ul[/tex]
ort
Which is a primary alcohol?
0 3-pentanol
2-propanol
1-ethanol
4-octanol
urvey
Lig A Moving to another question will save this response.
Answer:
1 ethanol is right answer
Explanation:
CH3- CH2-OH
If 50.0 g of sulfuric acid and 40.0 grams of barium chloride are mixed, how many grams of sulfuric acid and how many grams of barium chloride remain after the double replacement reaction is complete?
After the double replacement reaction is complete 0 grams of BaCl₂ and 31.16 grams of H₂SO₄ will remain.
First, we will write the balanced equation for the reaction
H₂SO₄ + BaCl₂ → BaSO₄ + 2HCl
This means 1 mole of BaCl₂ is needed to react completely with 1 mole of H₂SO₄ to give 1 mole of BaSO₄ and 2 moles of HCl
From the question, 50.0g of sulfuric acid is mixed with 40.0 grams of barium chloride. To determine the quantity of each substance remaining after the complete reaction, we will first determine the number of moles present in each of the reactant.
For H₂SO₄
mass = 50.0g
Molar mass = 98.079 g/mol
From the formula
Number of moles = Mass / Molar mass
∴ Number of moles of H₂SO₄ = 50.0g / 98.079 g/mol
Number of moles of H₂SO₄ = 0.5098 mol
For BaCl₂
mass = 40.0 g
Molar mass = 208.23 g/mol
∴ Number of moles of BaCl₂ = 40.0g / 208.23 g/mol
Number of moles of BaCl₂ = 0.1921 mol
Since the number of moles of H₂SO₄ is more than that of BaCl₂, then H₂SO₄ is the excess reagent and BaCl₂ is the limiting reagent (that is, it will be used up completely during the reaction)
From the equation, 1 mole of H₂SO₄ is needed to completely react with 1 mole of BaCl₂
∴ 0.1921 mol of H₂SO₄ will be needed to completely react with 0.1921 mol of BaCl₂.
Therefore, after the reaction is complete, 0 mole (i.e 0 grams) of BaCl₂ will remain and (0.5098 mole - 0.1921 mole) of H₂SO₄ will remain.
Number of moles H₂SO₄ that will remain = 0.5098 mole - 0.1921 mole = 0.3177 moles
Now, we will convert this to grams
From the formula
Mass = Number of moles × Molar mass
Mass of H₂SO₄ that will remain = 0.3177 moles × 98.079 g/mol
Mass of H₂SO₄ that will remain = 31.1597 g
Mass of H₂SO₄ that will remain ≅ 31.16 g
Hence, after the double replacement reaction is complete 0 grams of BaCl₂ and 31.16 grams of H₂SO₄ will remain.
Learn more here: https://brainly.com/question/6857557
What is the mass of carbon in 69.00 mg of co2
Answer:
18.82 mg
Explanation:
From the given information:
The molar mass of CO2 is calculated as follow
= (12 + (16 ×2))
= 44
The mass of carbon is determined by dividing the mass no of carbon from co2 by the molar mass of CO2, followed by multiplying it by 69.00 mg
= [tex](\dfrac{12}{44}\times 69 )[/tex]
=(0.2727 × 69 )
= 18.82 mg
A capsule containing 0.500 L of air at 1.00 atm is compressed to 3.25 atm. At that point, what is the volume of the gas in the capsule?
Answer:
V₂ = 0.154 Liters
Explanation:
Pressure => P
Volume => V
Temperature => T
mass (moles) => n
This problem...
P₁ = 1.00 ATM P₂ = 3.25 ATM
V₁ = 0.500L V₂ = ?
T₁ = constant T₂ = T₁ = constant
n₁ = constant n₂= n₁ = constant
P₁V₁/n₁T₁ = P₂V₂/n₂T₂ => V₂ = V₁(P₁/P₂) = 0.500L (1.00ATM/3.25ATM) = 0.154 Liters
To prepare a standard (calibration) curve for a spectroscopy experiment, start by preparing ___________ with ______________ Then, measure the ______________ of each solution at _____________ and create a plot of ____________ for the measured values. Finally, find the best-fit line of the data set.
Answer: See explanation
Explanation:
The calibration curve is the method used for the determination of the concentration of a substance such that the unknown sample will be compared to some standard samples of the known concentration.
To prepare a standard (calibration) curve for a spectroscopy experiment, start by preparing (multiple solutions) with (different known concentrations). Then, measure the (absorbance) of each solution at (thesame wavelength) and create a plot of (absorbance vs. concentration) for the measured values. Finally, find the best-fit line of the data set.
which of the following is is a chemical property of pure water
Answer:
Pure water has an acidity of about 7 on the pH scale. -is a chemical property of pure water. Pure water has an acidity of about 7 on the pH scale
Answer: không màu , không mùi không vị
Explanation:
Determine which choice is an example of an endothermic process.
O A. Lighting a match
B. Respiration
C. Running a gas engine
D. Baking bread
Answer:
D. Baking bread
Explanation:
In this process, energy is absorbed and in an endothermic process energy is absorbed too.
Baking bread is an example of an endothermic process, therefore option (d) is correct .
What do you mean by endothermic process ?Endothermic reactions are chemical processes in which the reactants absorb heat from the environment to produce products.
An endothermic reaction is accompanied by an absorption of heat.
Endothermic reactions cause a cooling effect by lowering the temperature of the surrounding environment.
A decrease in temperature can be observed with the progression of the reaction. The reaction is non-spontaneous in endothermic reactions .
Baking bread is an example of an endothermic process, hence option (d) is correct .
Learn more about endothermic process ,here:
https://brainly.com/question/23184814
#SPJ5
The Nernst equation at 20oC is:
Eion= 58 millvolts/z. [log10 (ion)out/(ion)in]
Calculate the equilibrium potential for Cl- if the concentration of Cl- outside of the cell is 100 and the concentration inside of the cell is 10 mmol/liter.
a. 58 millivolts
b. +58 millivolts
c. -116 millivolts
d. 0
Answer:
a. -58 millivolts
Explanation:
The given Nernst equation is:
[tex]E_{ion} = 58 millivolts /z \Big[ log_{10} \Big( \dfrac{[ion]_{out}}{[ion]_{in}}\Big) \Big]}[/tex]
The equilibrium potential given by the Nernst equation can be determined by using the formula:
[tex]E_{Cl^-} = \dfrac{2.303*R*T}{ZF} \times log \dfrac{[Cl^-]_{out}} {[Cl^-]_{in}}[/tex]
where:
gas constant(R) = 8.314 J/K/mol
Temperature (T) = (20+273)K
= 298K
Faraday constant F = 96485 C/mol
Number of electron on Cl = -1
[tex]E_{Cl^-} = \dfrac{2.303*8.314*298} {(-1)*(96845)} \times log \dfrac{100} {10}[/tex]
[tex]E_{Cl^-} = - 0.05814 \ volts[/tex]
[tex]\mathsf{E_{Cl^-} = - 0.05814 \times 1000 \ milli volts}[/tex]
[tex]\mathsf{E_{Cl^-} \simeq - 58\ milli volts}[/tex]
Match each land resource to its use.
clay - used to make steel
iron ore - used to make batteries
salt - used to make pottery and tiles
aggregate - used in construction
graphite - used as a flavoring in food
i will give 10 points and brainliest!!!
Answer:
Explanation:
We are to match each land resource to what they are being used for.
Clay →→→ used to make pottery and tiles
iron ore →→→ used to make steel
Salt →→→ used as a flavoring in food
aggregate →→→ used in construction
graphite →→→ used to make batteries
Clay is a kind of soil particle that forms as a result of weathering processes. Examples include; pottery clays, glacial clays, and deep-sea clays e.t.c. The presence of one or more clay minerals, as well as variable quantities of organic and detrital components, characterizes all of them. Clay is usually sticky and moist when wet, but hard when dry. They are used in the making of tiles and potteries.
Iron ore: The iron ore deposits are found in the Earth's crust's sedimentary rocks. They're made up of iron and oxygen that mix during the chemical process in marine and freshwater. iron ores are used to produce almost every iron and steel product that we use today.
Aggregate: are utilized in construction activities. It is a material used to mix cement, gypsum, bitumen, or lime to produce concrete in the construction industry.
Graphite: Graphite is a mineral that occurs in both igneous and metamorphic rocks. It is generally generated on the earth's surface when carbon is exposed to high temperatures and pressures. It is mainly used in the production of batteries and electrodes,
A sample of a compound is found to consist of 0.44g H and 6.92g O what’s its formula
Answer:
Explanation:
H = 0.44/1.01 = 0.4356
O = 6.92/16 = 0.4319
This gives a 1:1 ratio. So the closest thing you could say is the formula is 0H
Going to your chemical storage room, you could justify that it is H2O2 or hydrogen peroxide. The question needs one more fact to make the answer certainty.
