Answer:
D. 45 N
Explanation:
The weight of the block is 20 N, when the block is fully immerged in water, it weighs 15 N. Hence the loss of weight = 20 N - 15 N = 5 N.
The loss of weight is as a result of the buoyant force. The buoyant force is the upward force exerted by a fluid when an object is fully or partially immersed in a fluid.
The buoyant force of 5 N acts in the upward direction, the weight of the beaker that would be read by the scale when the beaker is immersed in water = 40 N + 5 N = 45 N
Introduction: The specific heat capacity of a substance is the amount of energy needed to change the temperature of that substance by 1 °C. Specific heat capacity can be calculated using the following equation:
q = mc deltaT
In the equation q represents the amount of heat energy gained or lost in joules), m is the mass of the substance (in grams), c is the specific heat capacity of the substance (in J/g °C), and AT is the temperature change of the substance in °C).
Goal: Calculate the specific heat capacities of copper, granite, lead, and ice.
Solve: When you mix two substances, the heat gained by one substance is equal to the heat lost by the other substance. Suppose you place 125 g of aluminum in a calorimeter with 1,000 g of water. The water changes temperature by 2 °C and the aluminum changes temperature by -74.95 °C.
A. Water has a known specific heat capacity of 4.184 J/g °C. Use the specific heat equation to find out how much heat energy the water gained (q).
B. Assume that the heat energy gained by the water is equal to the heat energy lost by the aluminum. Use the specific heat equation to solve for the specific heat of aluminum. Aluminum's accepted specific heat value is 0.900 J/g °C. Use this value to check your work.
Answer:
A) 8,368 J
B) ) 0.893 J/gºC
Explanation:
A)
The heat gained by the water can be obtained solving the following equation:[tex]q_{g} = c_{w} * m * \Delta T (1)[/tex]
where cw = specific heat of water = 4.184 J/gºCm= mass of water = 1,000 gΔT = 2ºC Replacing these values in (1) we get:[tex]q_{g} = c_{w} * m * \Delta T = 4.184 J/gºC*1,000 g* 2ºC = 8,368 J (2)[/tex]
B)
Assuming that the heat energy gained by the water is equal to the one lost by the aluminum, we can use the same equation, taking into account that the energy is lost by the aluminum, so the sign is negative: -8,368 J.Replacing by the mass of aluminum (125 g), and the change in temperature (-74.95ºC), in (1), we can solve for the specific heat of aluminum, as follows:[tex]q_{l} = c_{Al} * m_{Al} * \Delta T (3)[/tex]
⇒ [tex]-8,368 J = c_{Al}* 125 g * (-74.95ºC) (4)[/tex]
[tex]c_{Al} = \frac{-8,368J}{125g*(-74.95ºC} = 0.893 J/gºC (5)[/tex]
which is pretty close to the Aluminum's accepted specific heat value of 0.900 J/gºC.
If an atom of oxygen has an atomic number of eight that means...…
E. there are 8 protons
F. there are 8 neutrons
G. it weighs 8 amu
H. it is in group 8
Our Sun’s mass is 1.0 and our Earth’s mass is 2.0. The distance is standard as given on the simulation. Describe the path of the Earth.
Answer:
Earth orbits the Sun at an average distance of 149.60 million km (92.96 million mi), and one complete orbit takes 365.256 days (1 sidereal year), during which time Earth has traveled 940 million km (584 million mi).
Explanation:
Which is the best explanation for why Toms technique works ?
What is the instantaneous velocity of a freely falling object 11 s after it is released from a position of rest
Answer:
v= -107.8 m/s
Explanation:
Since the object is in free fall, this means that is moving at an accceleration equal to the one due to gravity.Since it starts at rest, we can apply the definition of acceleration, rearranging terms as follows:[tex]v_{f} = v_{o} + a*t = a*t = -g*t = 9.8m/s2*11s = -107.8 m/s (1)[/tex]
(Assuming as positive the upward direction)
Can a single atom be considered a molecule?
A:only if the atom is found in water
B:no, it takes two or more atoms bonded to create a molecule
C:only if it is an oxygen atom floating in the air
D:yes, all atoms are made up of many different molecules
A 71-kg swimmer dives horizontally off a 500-kg raft. If the diver's speed immediately after leaving the raft is 6m/s, what is the corresponding raft speed?
Answer:
The answer is below
Explanation:
Momentum is used to measure the quantity of motion in an object. Momentum is the product of mass and velocity.
Momentum = mass * velocity
The principle of conservation of momentum states that momentum cannot be created or destroyed but can be transferred. Therefore the momentum before and after an action is equal.
Initial momentum = Final momentum
Let m be the mass of the diver, M be the mass of the raft, u be the initial velocity of the diver, U be the initial velocity of the raft, v be the final velocity of the diver and V be the final velocity of the raft.
m = 71 kg, M = 500 kg, v = 6 m/s
Initial both the raft and diver are at rest, hence u and U is zero, hence:
mu + MU = mv + MV
71(0) + 500(0) = 71(6) + 500(V)
0 = 426 + 500(V)
500(V) = -426
V = -426/500
V = -0.852 m/s
If a car is traveling at an average speed of 20 m/s, how long will it take to travel 500 meters?
A. 0.04 seconds
B. 25 seconds
C. 520 seconds
D. 10,000 seconds
Answer:
B. 25 seconds
Explanation:
500÷20=25
Lisa skips 5 m North to the playground. She realizes she forgot to bring water so she turns around and goes 3 m South to the convenience store
Answer:
-2 South
Always subtract where they ended first is what my teacher said
What relationship must exist between an applied force and the velocity of a moving object if uniform circular motion is to result?
Answer:
See explanation
Explanation:
Centripetal force is defined as the inward force required to keep an object moving with a constant speed in a circular path.
The magnitude of this force depends on the mass of the object, radius of the object and the velocity of the body.
So we can write;
F = mv^2/r
A spring stretches by 15cm when a mass of 300g hangs down from it,if the spring is then stretched an additional 10cm and released, calculate;the spring constant,the angular velocity, amplitude of oscillation, maximum velocity, maximum acceleration of the mass,period, frequency
Answer:
0.1 m
Explanation:
It is given that,
Mass of the object, m = 350 g = 0.35 kg
Spring constant of the spring, k = 5.2 N/m
Amplitude of the oscillation, A = 10 cm = 0.1 m
Frequency of a spring mass system is given by :
Time period:
describe measurement in our daily life
I need this done by tonight!! Can anyone help me please? Answer these 4 questions
Answer:
1. 14 g of chocolate mixture.
2. 24 fl oz of chocolate milk
3. 10 cups of chocolate milk.
4. 12½ cups.
Explanation:
From the question given above, the following data were obtained:
1 TBSP = 7 g
1 Cup = 8 fl oz
2 Table spoons (TBSP) for 1 cup (8 fl oz) of milk.
1. Determination of the mass of chocolate mixture in 1 cup of chocolate milk.
From the question given above,
1 Cup required 2 Table spoons (TBSP)
But
1 TBSP = 7 g
Therefore,
2 TBSP = 2 × 7 = 14 g
Thus, 1 Cup required 14 g of chocolate mixture.
2. Determination of the number fl oz of chocolate milk in 3 cups
1 Cup = 8 fl oz
Therefore,
3 Cups = 3 × 8
3 Cups = 24 fl oz
Thus, 24 fl oz of chocolate milk are in 3 cups.
3. Determination of the number of cups of chocolate milk produce from 20 TBSP.
2 TBSP is required to produce 1 cup.
Therefore,
20 TBSP will produce = 20/2 = 10 Cups.
Thus, 10 cups of chocolate milk produce from 20 TBSP.
4. Determination of the number of cups obtained from 100 fl oz chocolate milk.
8 fl oz is required to produce 1 cup.
Therefore,
100 fl oz will produce = 100 / 8 = 12½ cups.
Thus, 12½ cups is obtained from 100 fl oz chocolate milk.
A safety plug is designed to melt when the pressure inside a metal tank becomes too high. A gas
at 51.0 atm and a temperature of 23.0°C is contained in the tank, but the plug melts when the
pressure reaches 75.0 atm. What temperature did the gas reach?
A 62 kg student, starting from rest, slide down an 10.6 m high water slide. How fast is he going at the bottom of the slide? Use g = 10 m/s2
Answer:
14.6m/s
Explanation:
Given parameters:
Mass of the student = 62kg
Initial velocity = 0m/s
Height of slide = 10.6m
g = 10m/s²
Unknown:
Speed at the bottom of the slide = ?
Solution:
The speed at the bottom of the slide is the final velocity;
v ² = u² + 2gh
v is the final velocity
u is the initial velocity
g is the acceleration due to gravity
h is the height
v² = 0² + 2x 10 x 10.6
v² = 212
v = 14.6m/s
A ball is thrown vertically upward from the top of a 100 foot tower, with an initial velocity of 10 ft/sec. Its position function is s(t)=−16t2+10t+100.
a. What is its velocity in ft/sec when t = 2 seconds? (Solve by using instantaneous rate.)
b. Determine the equation of a line, in slope-intercept form, that passes through the points (5, 6) and (10, 2).
Answer;
-54ft/s
y = -4/5 x + 10
Explanation
Given the position of an object expressed by the function
s(t)=−16t²+10t+100
Velocity is the change in position with respect to time
v(t) = ds(t)/dt
v(t) = -32t + 10
When t = 2
v(2) = -32(2)+10
v(2) = -64+10
v(2) = -54
Hence the velocity of the object is -54ft/s
b) The standard equation of a line in point slope form is expressed as;
y = MX+c
M is the slope
c is the y-intercept
Given the coordinate (5, 6) and (10, 2)
M = 2-6/10-5
M = -4/5
Get the y-intercept
Substitute m = -4/5 and any point say (5,6) into the expression y = mx+c
6 = -4/5 (5) + c
6 = -4+c
c = 6+4
c = 10
Get the required equation
Recall that: y = mx+c
y = -4/5 x + 10
Hence the equation of a line, in slope-intercept form is y = -4/5 x + 10
You are holding two balloons of the same shape and size. One is filled with helium, and the other is filled with ordinary air. On which balloon the buoyant force is greater?
a. The helium filled balloon experiences the greater buoyant force.
b. The air filled balloon experiences the greater buoyant force.
c. Both balloons experiences same buoyant force.
Answer:
Both balloons experiences same buoyant force.
Explanation:
Buoyant force is defined as the upward force that is exerted on an object which is wholly or partly immersed in a fluid. We can also define it as the upward force exerted by any fluid upon a body immersed in it. We may also refer to this buoyant force as the upthrust.
This buoyant force is the push of air on the balloon and it is independent of the contents of the balloons. Hence, both balloons experiences same buoyant force.
Assuming no friction, how does the initial gravitational potential energy of
the marble on a downward slope compare to the final kinetic energy?
a) they are the same
b) the initial gravitational potential energy is greater than the final kinetic energy
c) the initial gravitational potential energy is less then the final kinetic energy
Answer:
a) They are the same.
Explanation:
Assuming no friction, there should be no energy transfer and thus the Law of Conservation of Energy says:
[tex]PE=KE,\\mgh=\frac{1}{2}mv^2[/tex]
These types of problems also disregard any air resistance the surface of the object may cause. Therefore, no energy is transferred and from the Law of Conservation of Energy, [tex]100\%[/tex] of energy is preserved.
what is the pressure on a swimmer 50 m below the surface of a lake
Answer:
P = 490500 [Pa]
Explanation:
The pressure at the bottom of a vessel and even of a lake or sea can be calculated by means of the following hydrostatic equation.
[tex]P=Ro*g*h[/tex]
where:
P = pressure [Pa] (units of pascal)
Ro = water density = 1000 [kg/m³]
g = gravity acceleration = 9.81 [m/s²]
h = elevation = 50 [m]
Now replacing:
[tex]P=1000*9.81*50\\P=490500[Pa][/tex]
What is the function
of second plate in
parallel plate capacitor?
In which part of a lab report would be the following sentence most likely occur? “Since the data showed that the
Answer:
most likely be included in the analysis section of a lab report
Explanation:
PLS HELP ME!
A motorist is traveling 40ms-¹ and applies brakes and slow down at a rate of 2ms-² the available distance for the the motorist to stop is 400m will the motorist be able to stop?
Answer:
[tex] \underline{ \boxed{ yes}}\\[/tex]
Explanation:
[tex]given : initial \: velocity \: (u )= 40 {ms}^{ - 1} \\ given : final \: velocity \: (u )= 0 {ms}^{ - 1} \\ given : - (acceleration) \: (a_r) = 2 {ms}^{ - 2} \\ given : distance \: (s) \: = \: ? : \\ but \: {v}^{2} = {u}^{2} + 2( a)s\\ {0}^{2} = {40}^{2} + 2( - 2)s \\ - {40}^{2} = - 4s \\ s = \frac{ - {40}^{2} }{ - 4} \\ s = \frac{1600}{4} \\s = 400 \: m[/tex]
____ is factual information not subject to bias.
Interpretation
Analysis
Data
Opinion
Answer:
Data
Explanation:
Data is factual information not subject to bias.
This ultimately implies that, data connotes fact, thus, it is an information that is credible, accurate, a statement of truth, evidential and proven.
In Computer programming, a data dictionary can be defined as a centralized collection of information on a specific data such as attributes, names, fields and definitions that are being used in a computer database system.
In a data dictionary, data elements are combined into records, which are meaningful combinations of data elements that are included in data flows or retained in data stores.
This ultimately implies that, a data dictionary found in a computer database system typically contains the records about all the data elements (objects) such as data relationships with other elements, ownership, type, size, primary keys etc. This records are stored and communicated to other data when required or needed.
Many scientific studies have found that colds are caused by viruses. What is this? *
Fact
Interpretation
Analysis
Opinion
In designing buildings to be erected in an area prone to earthquakes, what relationship should the designer try to achieve between the natural frequency of the building and the typical earthquake frequencies?
A) The natural frequency of the building should be exactly the same as typical earthquake frequencies.
B) The natural frequency of the building should be almost the same as typical earthquake frequencies but slightly lower
C) The natural frequency of the building should be very different frem typical earthquake frequencies
D) The natural frequency of the building should be almost the same as typical earthquake frequencies but slightly higher.
Answer:
C) The natural frequency of the building should be very different from typical earthquake frequencies
Explanation:
We shall apply the concept of resonance in this problem .
When a body is applied an external harmonic force ( forced vibration) such that natural frequency of body is equal to frequency of external force or periodicity of external force , the body vibrates under resonance ie its amplitude of vibration becomes very high .
In the present case if natural frequency of building becomes equal to the earthquake's frequency ( external force ) , the building will start vibrating with maximum amplitude , resulting into quick collapse of the whole building . So to avoid this situation , natural frequency of building should be very different from typical earthquake frequencies .
An object is released from rest at a height H near and above the surface of Earth. As the object falls toward the surface, Earth’s atmosphere exerts a resistive force on the object such that it reaches a terminal velocity before it reaches the ground. Which of the following claims is true? Select two answers.
The system consisting of only the object is an open system.
The system consisting of only the object is an open system.
A
Earth’s atmosphere does negative work on the object as it falls toward the surface.
Earth’s atmosphere does negative work on the object as it falls toward the surface.
B
The change in the object’s kinetic energy from the instant it is released from rest, to the instant it reaches terminal velocity, is zero.
The change in the object’s kinetic energy from the instant it is released from rest, to the instant it reaches terminal velocity, is zero.
C
The total mechanical energy of the object-Earth system remains constant at all times in which the object is in motion.
Answer:
Second and Last Option Are Correct
Explanation:
a student lift a 25kg mass at vertical distance of 1.6m in a time of 2.0 seconds. a. Find the force needed to lift the mass (in N ). b. Find the work done by the student (in J). c. Find the power exerted by the student (in W)
Answer:
a. F = 245 Newton.
b. Workdone = 392 Joules.
c. Power = 196 Watts
Explanation:
Given the following data;
Mass = 25kg
Distance = 1.6m
Time = 2secs
a. To find the force needed to lift the mass (in N );
Force = mass * acceleration
We know that acceleration due to gravity is equal to 9.8
F = 25*9.8
F = 245N
b. To find the work done by the student (in J);
Workdone = force * distance
Workdone = 245 * 1.6
Workdone = 392 Joules.
c. To find the power exerted by the student (in W);
Power = workdone/time
Power = 392/2
Power = 196 Watts.
the diameter of the wheels on your car ( including the tires) is 25 inches. you are going to drive 250 miles today. each of your wheels is goingnto turn by an angle of
true or false A person's speed around the Earth is faster at the poles than it is at the equator.
Answer:False
Explanation:The Earth rotates faster at the equator than at the poles.
Two objects are interacting but stay stationary. Which best describes what is happening to he action and reaction forces
Answer: B
Explanation: The forces are equal and opposite each other.
When two objects are interacting but stay stationary, then the forces are equal and opposite each other.
What do you mean by Force?Force may be defined as the process of pushing and pulling an object with an actual mass that stimulates its velocity to be changed. It is a type of vector quantity because it has both magnitude and direction.
It is the simple and fundamental concept of physics that when two or more objects are interacting with one another but do stimulate any change in their position, the forces among them are definitely equal and opposite to one another. It is the most plausible explanation of Newton's third law of motion.
Therefore, when two objects are interacting but stay stationary, then the forces are equal and opposite each other.
To learn more about Newton's law of motion, refer to the link:
https://brainly.com/question/14222453
#SPJ6
Your question seems incomplete. The most probable complete question is as follows:
The forces are equal and opposite each other. The forces are not equal and opposite to each other. The forces are equal but not opposite to each other.The forces are not equal but opposite to each other.