Answer:
0.023 Ohms
Explanation:
Given data
Length= 2.8m
radius= 1.03mm
current I= 1.35 A
voltage V= 0.032V
We know that from Ohm's law
V= IR
Now R= V/I
Substitute
R= 0.032/1.35
R= 0.023 Ohms
Hence the resistance is 0.023 Ohms
After enjoying a tasty meal of the first moth, the bat goes after another moth. Flying with the same speed and emitting the same frequency, this time the bat detects a reflected frequency of 55.5 kHz. How fast is the second moth moving
This question is incomplete, the complete question is;
A bat flies towards a moth at 7.1 m/s while the moth is flying towards the bat at 4.4 m/s. The bat emits a sound wave of 51.7 kHz.
After enjoying a tasty meal of the first moth, the bat goes after another moth. Flying with the same speed and emitting the same frequency, this time the bat detects a reflected frequency of 55.5 kHz. How fast is the second moth moving
Answer:
the second moth is moving at 5.062 m/s
Explanation:
Given the data in the question;
Using doppler's effect
[tex]f_{moth[/tex] = f₀( [tex]v_{s[/tex] ± [tex]v_{observer[/tex] / [tex]v_{s[/tex] ± [tex]v_{source[/tex] )
f₁ = f₀( ([tex]v_{s[/tex] + v₂) / ( [tex]v_{s[/tex] - v₁ ) )
frequency reflected from the moth,
Now, moth is the source and the bat is the receiver
f₂ = f₁( ([tex]v_{s[/tex] + v₁ ) / ( [tex]v_{s[/tex] - v₂ ) )
hence, f = f₀[ ( ( [tex]v_{s[/tex] + v₁ ) / ( [tex]v_{s[/tex] - v₂ ) ) ( ( [tex]v_{s[/tex] + u₂ ) / ( [tex]v_{s[/tex] - u₁ ) )
we know that, the velocity of sound [tex]v_{s[/tex] = 343 m/s.
given that v₁ and v₂ { velocity of bat } = 7.1 m/s, f₀ = 51.7 kHz and f = 55.5 kHz.
we substitute
55.5 = 51.7[ ( ( 343 + 7.1 ) / ( 343 - 7.1 ) ) ( ( 343 + u ) / ( 343 - u ) ) ]
55.5 = 51.7[ ( 350.1 / 335.9 ) ( ( 343 + u ) / ( 343 - u ) ) ]
55.5 = 51.7[ 1.04227 ( ( 343 + u ) / ( 343 - u ) ) ]
55.5 = 53.885359 ( ( 343 + u ) / ( 343 - u ) ) ]
55.5 / 53.885359 = ( 343 + u ) / ( 343 - u )
1.02996 = ( 343 + u₂ ) / ( 343 - u )
( 343 + u₂ ) = 1.02996( 343 - u )
343 + u = 353.27628 - 1.02996u
u + 1.02996u = 353.27628 - 343
2.02996u = 10.27628
u = 10.27628 / 2.02996
u = 5.062 m/s
Therefore, the second moth is moving at 5.062 m/s
If a car drives 10 mph South, this is an example of a:
A. Displacement
B. Velocity
C. Speed
D. Distance
Answer:
杰杰伊杜杜杜伊格富尔杰迪耶赫分离福音
Explanation:
莱德利 · 赫耶尔伊 3uritievrirjrirhruebwkwieheoo2hfjcbvi3hd
Answer:
B velocity
Explanation:
1. A 2.7-kg copper block is given an initial speed of 4.0 m/s on a rough horizontal surface. Because of friction, the block finally comes to rest. (a) If the block absorbs 85% of its initial kinetic energy as internal energy, calculate its increase in temperature.
Answer:
ΔT = 0.017 °C
Explanation:
According to the given condition, the change in internal energy of the block must be equal to 85% of its kinetic energy:
Change in Internal Energy = (0.85)(Kinetic Energy)
[tex]mC\Delta T = (0.85)\frac{1}{2}mv^2\\\\C\Delta T = (0.425)v^2\\\\\Delta T = \frac{0.425v^2}{C}[/tex]
where,
ΔT = increase in temperature = ?
v = speed of block = 4 m/s
C = specific heat capacity of copper = 389 J/kg.°C
Therefore,
[tex]\Delta T = \frac{(0.425)(4\ m/s)^2}{389}\\\\[/tex]
ΔT = 0.017 °C
A boy walks from point C to point D which is 50 m apart. Then, he walks back to point C. what is his displacement of his whole journey ?
A.25 m
B.75 m
C.50 m
D.0 m
Answer: D. 0 m
Explanation:
Concept:
Here, we need to know the concept of displacement.
Displacement is defined to be the change in position of an object.
The difference between displacement and distance is the total movement of an object without any regard to direction, while displacement is the pure change of position.
If you are still confused, please refer to the attachment below for a graphical explanation.
Solve:
STEP ONE: the boy walks from point C to point D (a distance of 50 m)
C ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ D
50 m
STEP TWO: the boy walks from point D to point C (a distance of 50 m)
D ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ ⇒ C
50 m
STEP THREE: find the displacement
The boy started with point C
The boy ended with point C
He did not change his position throughout the journey.
Therefore, his displacement is 0 m.
Hope this helps!! :)
Please let me know if you have any questions
I NEEED HELP IN PHYSICS PLEASE!
Answer:
in which topic you need help
OBJECTI
1. The motion of a liquid inside a U-tube is an
example of what type of motion?
a. Simple Harmonic c. Random
b.Rectilinear
d. Circular
Answer:
option A
Explanation:
simple harmonic motion
Answer:
random motion I think not sure
Can Some1 help??
When using the "ball and stick" drawing method of drawing a compound, which element usually goes in the center of the model?
The US currently produces about 27 GW of electrical power from solar installations. Natural gas, coal, and oil powered installations produce about 740 GW of electrical power. The average intensity of electromagnetic radiation from the sun on the surface of the earth is 1000 W/m2 . If solar panels are 30% efficient at converting this incident radiation into electrical power, what is the total surface area of solar panels responsible for the 27 GW of power currently produced
Answer:
The total surface area is "90 km²".
Explanation:
Given:
Power from solar installations,
= 27 GW
Other natural installations,
= 740 GW
Intensity,
[tex]\frac{F}{At}=\frac{P}{A}=1000 \ W/m^2[/tex]
%n,
= 30%
Now,
⇒ %n = [tex]\frac{out.}{Inp.}\times 100[/tex]
then,
⇒ [tex]Inp.=\frac{27}{30}\times 100[/tex]
[tex]=90 \ GW[/tex]
As we know,
⇒ [tex]I=\frac{P}{A}[/tex]
by substituting the values, we get
[tex]1000=\frac{90\times 10^9}{A}[/tex]
[tex]A = \frac{90\times 10^9}{10^3}[/tex]
[tex]=90\times 10^6[/tex]
[tex]=90 \ km^2[/tex]
Difference between scissors and nut cracker
The kinetic energy of a particle of mass 500g is 4.8j. Determine the velocity of the particle
Answer:
4.38 m/s
Explanation:
A boat is able to move at 7.6 m/s in still water. If the boat is placed on the south shore of a river (water current of 3.4 m/s [SE]), and the captain wants to head straight across to the north shore:
a) In what direction should the captain point the boat?
b) Calculate the time it will take to cross (the river is 212.0 m from the south to the north shore).
Answer:
I don't get it rewrite please
Identify each action as a wave erosion war wind erosion
Answer:Lesson Objectives
Describe how the action of waves produces different shoreline features.
Discuss how areas of quiet water produce deposits of sand and sediment.
Discuss some of the structures humans build to help defend against wave erosion.
Vocabulary
arch
barrier island
beach
breakwater
groin
refraction
sea stack
sea wall
spit
wave-cut cliff
wave-cut platform
Introduction
Waves are important for building up and breaking down shorelines. Waves transport sand onto and off of beaches. They transport sand along beaches. Waves carve structures at the shore.
Wave Action and Erosion
All waves are energy traveling through some type of material, such as water (Figure below). Ocean waves form from wind blowing over the water.
Ocean waves are energy traveling through water.
The largest waves form when the wind is very strong, blows steadily for a long time, and blows over a long distance.
The wind could be strong, but if it gusts for just a short time, large waves won’t form. Wave energy does the work of erosion at the shore. Waves approach the shore at some angle so the inshore part of the wave reaches shallow water sooner than the part that is further out. The shallow part of the wave ‘feels’ the bottom first. This slows down the inshore part of the wave and makes the wave ‘bend.’ This bending is called refraction.
Wave refraction either concentrates wave energy or disperses it. In quiet water areas, such as bays, wave energy is dispersed, so sand is deposited. Areas that stick out into the water are eroded by the strong wave energy that concentrates its power on the wave-cut cliff (Figure below).
The wave erodes the bottom of the cliff, eventually causing the cliff to collapse.
Other features of wave erosion are pictured and named in Figure below. A wave-cut platform is the level area formed by wave erosion as the waves undercut a cliff. An arch is produced when waves erode through a cliff. When a sea arch collapses, the isolated towers of rocks that remain are known as sea stacks.
(a) The high ground is a large wave-cut platform formed from years of wave erosion. (b) A cliff eroded from two sides produces an arch. (c) The top of an arch erodes away, leaving behind a tall sea stack.
Wave Deposition
Rivers carry sediments from the land to the sea. If wave action is high, a delta will not form. Waves will spread the sediments along the coastline to create a beach (Figure below). Waves also erode sediments from cliffs and shorelines and transport them onto beaches.
Sand deposits in quiet areas along a shoreline to form a beach.
Beaches can be made of mineral grains, like quartz, rock fragments, and also pieces of shell or coral (Figure below).
Quartz, rock fragments, and shell make up the sand along a beach.
Waves continually move sand along the shore. Waves also move sand from the beaches on shore to bars of sand offshore as the seasons change. In the summer, waves have lower energy so they bring sand up onto the beach. In the winter, higher energy waves bring the sand back offshore.
Some of the features formed by wave-deposited sand are in Figure below. These features include barrier islands and spits. A spit is sand connected to land and extending into the water. A spit may hook to form a tombolo.
Examples of features formed by wave-deposited sand.
Shores that are relatively flat and gently sloping may be lined with long narrow barrier islands (Figure below). Most barrier islands are a few kilometers wide and tens of kilometers long.
(a) Barrier islands off of Alabama. A lagoon lies on the inland side. (b) Barrier islands, such as Padre Island off the coast of Texas, are made entirely of sand. (c) Barrier islands are some of the most urbanized areas of our coastlines, such as Miami Beach.
In its natural state, a barrier island acts as the first line of defense against storms such as hurricanes. When barrier islands are urbanized (Figure above), hurricanes damage houses and businesses rather than vegetated sandy areas in which sand can move. A large hurricane brings massive problems to the urbanized area.
Protecting Shorelines
Intact shore areas protect inland areas from storms that come off the ocean (Figure below).
Dunes and mangroves along Baja California protect the villages that are found inland.
Explanation:
Answer: Below
Explanation: Correct on Edmentum
An ideal spring is hung vertically from the ceiling. When a 2.0-kg mass hangs at rest from it the spring is extended 6.0 cm from its relaxed length. A downward external force is now applied to the mass to extend the spring an additional 10 cm. While the spring is being extended by the force, the work done by the spring is:
a. -3.6 J
b. -3.3 F
c. -3.4 times 10^-5 J
d. 3.3 J
e. 3.6 J
Answer:
b) - 3.3 J
Explanation:
Given;
mass, m = 2 kg
initial extension of the spring, x = 6 cm = 0.06 m
The weight of the mass on the spring;
W = mg
where;
g is acceleration due to gravity = 9.81 m/s²
W = 2 x 9.81
W = 19.62 N
The spring constant is calculated as;
W = kx
k = W/x
k = 19.62 / 0.06
k = 327 N/m
The work done by the spring when it is extended to an additional 10 cm;
work done = force x distance
distance = extension, x = 10 cm = 0.1 m
The work done by the spring opposes the applied force by acting in opposite direction to the force.
W = - Fx
W = - (kx) x
W = - kx²
W = - (327) x (0.1)²
W = - 3.27 J
W ≅ - 3.3 J
Therefore, the work done by the spring by opposing the applied force is -3.3 J
What do you understand by moment of inertia and torque?
Word limit 50-60
Please don't copy from any sources. You can rewrite. Plagiarism will be check. Thank you.
Answer:
Moment of inertia, in physics, quantitative measure of the rotational inertia of a body—i.e., the opposition that the body exhibits to having its speed of rotation about an axis altered by the application of a torque (turning force). The axis may be internal or external and may or may not be fixed.
Ibrah open a bottle of perfume infront of the room. After few minutes the smell of perfume reach the whole room. Explain why this happens
calculate the value of 200°C in Kelvin
Answer:
473.15
Explanation:
An equation for the period of a planet is 4 pie² r³/Gm where T is in secs, r is in meters, G is in m³/kgs² m is in kg, show that the equation is dimensionally correct.
Answer:
[tex]\displaystyle T = \sqrt{\frac{4\, \pi^{2} \, r^{3}}{G \cdot m}}[/tex].
The unit of both sides of this equation are [tex]\rm s[/tex].
Explanation:
The unit of the left-hand side is [tex]\rm s[/tex], same as the unit of [tex]T[/tex].
The following makes use of the fact that for any non-zero value [tex]x[/tex], the power [tex]x^{-1}[/tex] is equivalent to [tex]\displaystyle \frac{1}{x}[/tex].
On the right-hand side of this equation:
[tex]\pi[/tex] has no unit.The unit of [tex]r[/tex] is [tex]\rm m[/tex].The unit of [tex]G[/tex] is [tex]\displaystyle \rm \frac{m^{3}}{kg \cdot s^{2}}[/tex], which is equivalent to [tex]\rm m^{3} \cdot kg^{-1} \cdot s^{-2}[/tex].The unit of [tex]m[/tex] is [tex]\rm kg[/tex].[tex]\begin{aligned}& \rm \sqrt{\frac{(m)^{3}}{(m^{3} \cdot kg^{-1} \cdot s^{-2}) \cdot (kg)}} \\ &= \rm \sqrt{\frac{m^{3}}{m^{3} \cdot s^{-2}}} = \sqrt{s^{2}} = s\end{aligned}[/tex].
Hence, the unit on the right-hand side of this equation is also [tex]\rm s[/tex].
A runner has a temperature of 40°c and is giving off heat at the rate of 50cal/s (a) What is the rate of heat loss in watts? (b) How long will it take for this person's temperature to return to 37°c if his mass is 90kg.
Answer:
(a) 209 Watt
(b) 4482.8 seconds
Explanation:
(a) P = 50×4.18
Where P = rate of heat loss in watt
P = 209 Watt
Applying,
Q = cm(t₁-t₂)................ Equation 1
Where Q = amount of heat given off, c = specific heat capacity capacity of human, m = mass of the person, t₁ and t₂ = initial and final temperature.
From the question,
Given: m = 90 kg, t₁ = 40°C, t₂ = 37°C
Constant: c = 3470 J/kg.K
Substtut these values into equation 1
Q = 90×3470(40-37)
Q = 936900 J
But,
P = Q/t.............. Equation 2
Where t = time
t = Q/P............ Equation 3
Given: P = 209 Watt, Q = 936900
Substitute into equation 3
t = 936900/209
t = 4482.8 seconds
What happens to the temperature of matter as distance is increased? Explain why.
Answer:
The tempature of the matter increases.
Explanation:
The matter is heated by friction, weather that is through the air or if its touching the ground like a car.
please mark me as brainliest of this is right, thanks
A standard bathroom scale is placed on an elevator. A 28 kg boy enters the elevator on the first floor and steps on the scale. What will the scale read (in newtons) when the elevator begins to accelerate upward at 0.5 m/s2
Answer:
Explanation:
Newton's Second Law is pretty much the standard for all motion that involves a force. It applies to gravitational force and torque and friction and weight on an elevator. The main formula for force is
F = ma. We have to adjust that to take into account that when the elevator is moving up, that "surge" of acceleration weighs down a bit on the scale, causing it to read higher than the actual weight until the acceleration evens out and there is no acceleration at all (no acceleration simply means that the velocity is constant; acceleration by definition is a change in velocity, and if there is no change in velocity, there is 0 acceleration). The force equation then becomes
[tex]F_n-w=ma[/tex] where [tex]F_n[/tex] is normal force. This is what the scale will read, which is what we are looking for in this problem (our unknown). Since we are looking for [tex]F_n[/tex], that is what we will solve this literal equation for:
[tex]F_n=ma+w[/tex] . m is the mass of the boy, a is the acceleration of the elevator (which is going up so we will call that acceleration positive), and w is weight. We have everything but the unknown and the weight of the boy. We find the weight:
w = mg so
w = 28(9.8) and
w = 274.4 N BUT rounding to the correct number of significance we have that the weight is actually
w = 270 N.
Filling in the elevator equation:
[tex]F_n=28(.50)+270[/tex] and according to the rules of significant digits, we have to multiply the 28(.50) {notice that I did add a 0 there for greater significance; if not that added 0 we are only looking at 1 significant digit which is pretty much useless}, round that to 2 sig fig's, and then add to 170:
[tex]F_n=14+270[/tex] and adding, by the rules, requires that we round to the tens place to get, finally:
[tex]F_n=280N[/tex] So you see that the surge in acceleration did in fact add a tiny bit to the weight read by the scale; conversely, if he were to have moved down at that same rate, the scale would have read a bit less than his actual weight). Isn't physics like the coolest thing ever!?
A body is supported by a helical spring and causes an extension of 1.5 cm in the spring. If the mass is set into vertical oscillation, calculate the period of the oscillation.
Answer:
please follow Me
Explanation:
if the answer is right then like me otherwise you can share the right answer
A 2kg ball is rolled along the floor for 0.8 m at a constant speed of 6 m/s. What is the work done by gravity?
A, 0
B, 16 J
C, 72 J
D, 450 J
E, 90 J
=F×s×cosa=2×g×0,8×cos90°= 0
The work done by gravity on a ball of 2 kg which is moving with a constant speed of 6 meter per second is zero. Thus, the correct option is A.
What is Work?Work is the energy transfer to or from an object through the application of force along with the displacement. For a constant force aligned with the direction of motion, the work done is equal to the product of the force strength which is applied and the distance traveled by the object.
Work = Force × Displacement
Force = Mass × Acceleration
Acceleration of the ball is zero as it is moving with a constant speed. Therefore, the work done by the gravity is zero.
Therefore, the correct option is A.
Learn more about Work done here:
https://brainly.com/question/13662169
#SPJ2
If a marathon runner runs 9.5 miles in one direction, 8.89 miles in another direction, and 2.333 miles in a third direction, how much distance did the runner run?
We have that the total distance covered by the runner is
[tex]d_t=20.723miles[/tex]
The total distance covered by the runner is a sum of all miles covered by the runner
Therefore
With
[tex]d_t[/tex]=Total distance
[tex]d_t=d_1+d_2+d_3\\\\d_t=9.5+8.89+2.333[/tex]
[tex]d_t=20.723miles[/tex]
in conclusion
The total distance covered by the runner is
[tex]d_t=20.723miles[/tex]
For more information on this visit
https://brainly.com/question/12319416
Suppose your actual height is 5 feet and 5.2 inches. A tape measure which can be read tothe nearest 1/8 of an inch gives your height as 65 3/8 inches. The laser device at the clinic that givesreadings to the nearest hundredth of an inch says you are 65.31 inches.
Required:
a. Which measuring device is more accurate?
b. Which measuring device is more precise?
Answer:
a) The laser device
b) The tape
Explanation:
First, there is a need to understand what accuracy and precision mean.
Accuracy is the closeness of a measurement to its true (pre-determined) value.
Precision is the closeness of repeated measurements to each other.
Since 1 feet = 12 inches, then, 5 feet and 5.2 inches would be equivalent to 65.2 inches. This value represents the true value of my height.
The tape measured the height as 65 3/8, which is equivalent to 65.375 inches.
The laser device measured the height as 65.31.
Error = true value - measured value
Absolute error from the tape = 65.2 - 65.375
= -0.175 inches
Absolute error from laser device = 65.2 - 65.31
= -0.11
a) The magnitude of error from the tape is more than that of the laser device. Hence, the laser device is said to be more accurate.
b) Even though there were just single readings from both instruments, the tape can be read to the nearest 1/8 of an inch and as such, can give more precisive measurements than the laser device.
A man is pulling a 20 kg box with a rope that makes an angle of 60 with the horizontal.If he applies a force of 150 N and a frictional force of 15 N is present, calculate the acceleration of the box.
∑ F (horizontal) = (150 N) cos(60°) - 15 N = (20 kg) a
==> a = ((150 N) cos(60°) - 15 N)/(20 kg) = 3 m/s²
To calculate the acceleration of the box, we need to consider the net force acting on it. So, the acceleration of the box is 3 m/s².
The net force is the vector sum of the applied force and the force of friction. First, let's find the horizontal and vertical components of the applied force:
Horizontal component of the applied force (F[tex]_{horizontal}[/tex]) = F[tex]_{applied}[/tex] × cos(θ)
F[tex]_{horizontal}[/tex] = 150 N × cos(60°)
F[tex]_{horizontal}[/tex] = 150 N × 0.5
F[tex]_{horizontal}[/tex] = 75 N
Vertical component of the applied force (F[tex]_{vertical}[/tex]) = F[tex]_{applied}[/tex] × sin(θ)
F[tex]_{vertical}[/tex] = 150 N × sin(60°)
F[tex]_{vertical}[/tex] = 150 N × (√3 / 2)
F[tex]_{vertical}[/tex] ≈ 129.9 N
Now, let's calculate the net force in the horizontal direction:
Net Force in the horizontal direction (F[tex]_{net horizontal}[/tex]) = F[tex]_{horizontal}[/tex] - F[tex]_{friction}[/tex]
F[tex]_{net horizontal}[/tex] = 75 N - 15 N
F[tex]_{net horizontal}[/tex] = 60 N
Now, we can calculate the acceleration (a) using Newton's second law of motion, F = ma:
F[tex]_{net horizontal}[/tex] = m × a
60 N = 20 kg × a
Now, solve for acceleration (a):
a = 60 N / 20 kg
a = 3 m/s²
So, the acceleration of the box is 3 m/s².
To know more about acceleration
https://brainly.com/question/460763
#SPJ2
A block weighting 400kg rests on a horizontal surface and support on top of it another block of weight 100kg placed on the top of it as shown. The block w2 is attached to avertical wall by a string 6m long. If the coefficient of friction between all surface is 0.25 and the system is in equilibrium find the magnitude of the horizontal force applied to the lower block
The horizontal force applied to the block is approximately 1,420.84 N
The known parameters;
The mass of the block, w₁ = 400 kg
The orientation of the surface on which the block rest, w₁ = Horizontal
The mass of the block placed on top of the 400 kg block, w₂ = 100 kg
The length of the string to which the block w₂ is attached, l = 6 m
The coefficient of friction between the surface, μ = 0.25
The state of the system of blocks and applied force = Equilibrium
Strategy;
Calculate the forces acting on the blocks and string
The weight of the block, W₁ = 400 kg × 9.81 m/s² = 3,924 N
The weight of the block, W₂ = 100 kg × 9.81 m/s² = 981 N
Let T represent the tension in the string
The upward force from the string = T × sin(θ)
sin(θ) = √(6² - 5²)/6
Therefore;
The upward force from the string = T×√(6² - 5²)/6
The frictional force = (W₂ - The upward force from the string) × μ
The frictional force, [tex]F_{f2}[/tex] = (981 - T×√(6² - 5²)/6) × 0.25
The tension in the string, T = [tex]F_{f2}[/tex] × cos(θ)
∴ T = (981 - T×√(6² - 5²)/6) × 0.25 × 5/6
Solving, we get;
[tex]T = \dfrac{5886}{\sqrt{6^2 - 5^2} + 28.8} \approx 183.27[/tex]
[tex]Frictional \ force, F_{f2} = \left (981 - \dfrac{5886}{\sqrt{6^2 - 5^2} + 28.8} \times \dfrac{\sqrt{6^2 - 5^2} }{6} \times 0.25 \right) \approx 219.92[/tex]
The frictional force on the block W₂, [tex]F_{f2}[/tex] ≈ 219.92 N
Therefore;
The force acting the block w₁, due to w₂ [tex]F_{w2}[/tex] = 219.92/0.25 ≈ 879.68
The total normal force acting on the ground, N = W₁ + [tex]\mathbf{F_{w2}}[/tex]
The frictional force from the ground, [tex]\mathbf{F_{f1}}[/tex] = N×μ + [tex]\mathbf{F_{f2}}[/tex] = P
Where;
P = The horizontal force applied to the block
P = (W₁ + [tex]\mathbf{F_{w2}}[/tex]) × μ + [tex]\mathbf{F_{f2}}[/tex]
Therefore;
P = (3,924 + 879.68) × 0.25 + 219.92 ≈ 1,420.84
The horizontal force applied to the block, P ≈ 1,420.84 N
Learn more about friction force here;
https://brainly.com/question/18038995
why do we go to hospital
Answer:
bcz we want to have fun there lolol
Answer:
for emergency, treatment, medicines,etc.....
A capacitor consists of two metal surfaces separated by an electrical insulator with no electrically conductive path through it. Why does a current flow in a resistor-capacitor circuit when the switch is closed?
Answer:
Displacement current flows in the dielectric material(insulated region)
Explanation:
Firstly a capacitor stores charge when a capacitor is charging (or discharging), current flows in the circuit. Also, there is no charge transfer in the dielectric material in the capacitor which is contradictory to the flow of current. Hence, displacement current is the current in the insulated region due to the changing electric flux.
What star is known as the "cold planet"?
Explanation:
OGLE-2005-BLG-390Lb.
PSR B1620-26 b. Surface Temperature: 72 Kelvin. ...
Neptune. Surface Temperature: 72 Kelvin. ...
Uranus. Surface Temperature: 76 Kelvin. ...
Saturn. Surface Temperature: 134 Kelvin. ...
Jupiter. Image Courtesy: NASA. ...
OGLE-2016-BLG-1195Lb. Surface Temperature: Unknown
How can I solve this?
You have three capacitors of values 40 F, 10 F and 50 F. What would their equivalent capacitance (in F) be if they were connected in parallel with each other? Enter your answer as a number only, to one decimal place.
Explanation:
The equivalent capacitance of capacitors in parallel can be determined as
[tex]C_{eq} = C_1 + C_2 + C_3[/tex]
[tex]\:\:\:\:\:= 40\:\text{F} + 10\:\text{F} + 50\:\text{F} = 100\:\text{F}[/tex]
