A disk rotates about its central axis starting from rest and accelerates with constant angular acceleration. At one time it is rotating at 10 rev/s; 60 revolutions later, its angular speed is 15 rev/s. Calculate
(a) the angular acceleration,
(b) the time required to complete the 60 revolutions,
(c) the time required to reach the 10 rev/s angular speed, and
(d) the number of revolutions from rest until the time the disk reaches the 10 rev/s angular speed.

Answers

Answer 1

Explanation:

Given:

[tex]\omega_0[/tex] = 10 rev/s = [tex]20\pi\:\text{rad/s}[/tex]

[tex]\omega[/tex] = 15 rev/s = [tex]30\pi\:\text{rad/s}[/tex]

[tex]\theta[/tex] = 60 rev = [tex]120\pi\:\text{rads}[/tex]

a) the angular acceleration [tex]\alpha[/tex] is given by

[tex]\alpha = \dfrac{\omega^2 - \omega_0^2}{2\theta}[/tex]

[tex]\:\:\:\:\:\:\:=\dfrac{(30\pi)^2 - (20\pi)^2}{240\pi} = 6.5\:\text{rad/s}^2[/tex]

b) [tex]t = \dfrac{\omega - \omega_0}{\alpha} = \dfrac{30\pi - 20\pi}{6.5} = 4.8\:\text{s}[/tex]

c) [tex]t = \dfrac{\omega - \omega_0}{\alpha}[/tex]

[tex]=\dfrac{20\pi - 0}{6.5} = 9.7\:\text{s}[/tex]

d)[tex]\theta = \frac{1}{2}\alpha t^2[/tex]

[tex]\:\:\:\:\:\:\:=\frac{1}{2}(6.5\:\text{rad/s}^2)(9.7\:\text{s})^2 = 305.8\:\text{rad}[/tex]

[tex]\:\:\:\:\:\:\:= 48.7\:\text{revs}[/tex]


Related Questions

which has higher eneergy electron r proton

Answers

Answer:

proton have higher energy than electron

Explanation:

tag me brainliest

Answer:

proton

Explanation:

proton is higher energy than the electron

Which is the most difficult subject?​

Answers

Answer:

Quantum Mechanics

Explanation:

Well, that's what I think personally.

What is the effect on range and maximum height of a projectile as the launch height, launch speed, and launch angle are increased?

Answers

Answer:

The highest point in the trajectory occurs at the midpoint of the path. This highest point increases as the angle increases. At a 75° launch angle, the maximum height is approximately 76 meters. However, a further increase in launch angle beyond this 75° angle will increase the peak height even more.

i.Name two commonly used thermometric liquids.


ii.State two advantages each of the thermometric liquids mentioned above​

Answers

Answer:

mercury and alcohol

ii) used to test temperatures

Mercury and AlcoholMercury:

i) It is a good conductor of heat and therefore the whole liquid reaches the temperature of the surroundings quickly.

ii) It does not wet (cling to the sides of) the tube.

Alcohol:

i) Alcohol has greater value of temperature coefficient of expansion than mercury.

ii) it's freezing point is below –100°C.

At what rate must a cylindrical spaceship rotate if occupants are to experience simulated gravity of 0.58 g

Answers

Answer:

w = 1,066 rad / s

Explanation:

For this exercise we use Newton's second law

         F = m a

the centripetal acceleration is

         a = w² r

indicate that the force is the mass of the body times the acceleration

        F = m 0.58g = m 0.58 9.8

        F = 5.684 m

we substitute

       5.684 m = m w² r

       w = [tex]\sqrt{5.684/r}[/tex]

To finish the calculation we must suppose a cylinder radius, suppose it has r = 5 m

       w = [tex]\sqrt{ 5.684/5}[/tex]

       w = 1,066 rad / s

Physical quantities expresed only by their magnitude is​

Answers

Answer:

Scalar quantity is the Physical quantity expresed only by their magnitude.

Harmonics a.are components of a complex waveform. b.have frequencies that are integer multiples of the frequency of the complex waveform. c.are pure tones. d.have sinusoidal waveforms. e.all of the above

Answers

Answer:

b.have frequencies that are integer multiples of the frequency of the complex waveform

Explanation:

Please correct me if I am wrong

A double-slit experiment is performed with light of wavelength 550 nm. The bright interference fringes are spaced 2.3 mm apart on the viewing screen. What will the fringe spacing be if the light is changed to a wavelength of 360 nm?

Answers

Answer:

[tex]d_2=1.5*10^-3m[/tex]

Explanation:

From the question we are told that:

Initial Wavelength [tex]\lambda_1=550nm=550*10^{-9}[/tex]

Space 1 [tex]d_1=2.3*10^{-3}[/tex]

Final wavelength [tex]\lambda_2=360*10^{-9}[/tex]

Generally the equation for Fringe space at [tex]\lambda _2[/tex] is mathematically given by

 [tex]d_2=\frac{d_1}{\lambdaI_1}*\lambda_2[/tex]

 [tex]d_2=\frac{2.3*10^{-3}}{550*10^{-9}}*360*10^{-9}[/tex]

 [tex]d_2=1.5*10^-3m[/tex]

When air expands adiabatically (without gaining or losing heat), its pressure P and volume V are related by the equation PV1.4=C where C is a constant. Suppose that at a certain instant the volume is 420 cubic centimeters and the pressure is 99 kPa and is decreasing at a rate of 7 kPa/minute. At what rate in cubic centimeters per minute is the volume increasing at this instant?

Answers

Answer:

[tex]\frac{dV}{dt}=21.21cm^3/min[/tex]

Explanation:

We are given that

[tex]PV^{1.4}=C[/tex]

Where C=Constant

[tex]\frac{dP}{dt}=-7KPa/minute[/tex]

V=420 cubic cm and P=99KPa

We have to find the rate at which the  volume increasing at this instant.

Differentiate w.r.t t

[tex]V^{1.4}\frac{dP}{dt}+1.4V^{0.4}P\frac{dV}{dt}=0[/tex]

Substitute the values

[tex](420)^{1.4}\times (-7)+1.4(420)^{0.4}(99)\frac{dV}{dt}=0[/tex]

[tex]1.4(420)^{0.4}(99)\frac{dV}{dt}=(420)^{1.4}\times (7)[/tex]

[tex]\frac{dV}{dt}=\frac{(420)^{1.4}\times (7)}{1.4(420)^{0.4}(99)}[/tex]

[tex]\frac{dV}{dt}=21.21cm^3/min[/tex]

Answer:

[tex]\dot V=2786.52~cm^3/min[/tex]

Explanation:

Given:

initial pressure during adiabatic expansion of air, [tex]P_1=99~kPa[/tex]

initial volume during the process, [tex]V_1=420~cm^3[/tex]

The adiabatic process is governed by the relation [tex]PV^{1.4}=C[/tex] ; where C is a constant.

Rate of decrease in pressure, [tex]\dot P=7~kPa/min[/tex]

Then the rate of change in volume, [tex]\dot V[/tex] can be determined as:

[tex]P_1.V_1^{1.4}=\dot P.\dot V^{1.4}[/tex]

[tex]99\times 420^{1.4}=7\times V^{1.4}[/tex]

[tex]\dot V=2786.52~cm^3/min[/tex]

[tex]\because P\propto\frac{1}{V}[/tex]

[tex]\therefore[/tex] The rate of change in volume will be increasing.

1. What is the total distance the car moves until it stops?
a. 250 m
b. 450 m
c. 300 m
d. 600 m.​

Answers

B
Just took the quiz bro it was easy

A car is moving at a speed of 60 mi/hr (88 ft/sec) on a straight road when the driver steps on the brake pedal and begins decelerating at a constant rate of 10ft/s2 for 3 seconds. How far did the car go during this 3 second interval?

Answers

Answer:

219 ft

Explanation:

Here we can define the value t = 0s as the moment when the car starts decelerating.

At this point, the acceleration of the car is given by the equation:

A(t) = -10 ft/s^2

Where the negative sign is because the car is decelerating.

To get the velocity equation of the car, we integrate over time, to get:

V(t) = (-10 ft/s^2)*t + V0

Where V0 is the initial velocity of the car, we know that this is 88 ft/s

Then the velocity equation is:

V(t) = (-10 ft/s^2)*t + 88ft/s

To get the position equation we need to integrate again, this time we get:

P(t) = (1/2)*(-10 ft/s^2)*t^2 + (88ft/s)*t + P0

Where P0 is the initial position of the car, we do not know this, but it does not matter for now.

We want to find the total distance that the car traveled in a 3 seconds interval.

This will be equal to the difference in the position at t = 3s and the position at t = 0s

distance = P(3s) - P(0s)

 = ( (1/2)*(-10 ft/s^2)*(3s)^2+ (88ft/s)*3s + P0) - ( (1/2)*(-10 ft/s^2)*(0s)^2 + (88ft/s)*0s + P0)

=  ( (1/2)*(-10 ft/s^2)*9s^2+ (88ft/s)*3s + P0) - ( P0)

=  (1/2)*(-10 ft/s^2)*9s^2+ (88ft/s)*3s = 219ft

The car advanced a distance of 219 ft in the 3 seconds interval.

A 3.10 mol sample of an ideal diatomic gas expands adiabatically from a volume of 0.1550 m3 to 0.742 m3 . Initially the pressure was 1.00 atm.(a) Determine the initial and final temperatures.initial Kfinal K(b) Determine the change in internal energy. J(c) Determine the heat lost by the gas. J(d) Determine the work done on the gas. J

Answers

Answer:

a) Initial Temperature = 609.4 K and Final Temperature = 325.7 K

b) the change in internal energy is -18279.78 J

c) heat lost by the gas is zero or 0

d) the work done on the gas is -18279.78 J

Explanation:

Given the data in the question;

P[tex]_i[/tex] = 1 atm = 101325 pascal

P[tex]_f[/tex] = ?

V[tex]_i[/tex] = 0.1550 m³

V[tex]_f[/tex] = 0.742 m³

we know that for an adiabatic process  γ = 1.4

P[tex]_i[/tex]V[tex]_i^Y[/tex] = P[tex]_f[/tex]V[tex]_f^Y[/tex]

P[tex]_f[/tex] = P[tex]_i[/tex][tex]([/tex] V[tex]_i[/tex] / V[tex]_f[/tex] [tex])^Y[/tex]

we substitute

P[tex]_f[/tex] = 1 × [tex]([/tex] 0.1550  / 0.742  [tex])^{1.4[/tex]

= [tex]([/tex] 0.2088948787 [tex])^{1.4[/tex]

= 0.11166 atm

a) the initial and final temperatures

Initial temperature

T[tex]_i[/tex] = P[tex]_i[/tex]V[tex]_i[/tex] / nR

given that n = 3.10 mol

= ( 101325 × 0.1550 ) / ( 3.10 × 8.314 )

= 15705.375 / 25.7734

T[tex]_i[/tex]  = 609.4 K

Final temperature

T[tex]_f[/tex] = P[tex]_f[/tex]V[tex]_f[/tex] / nR

= ( 0.11166 × 101325 × 0.742 ) / ( 3.10 × 8.314 )

= 8394.95 / 25.7734

= 325.7 K

Therefore, Initial Temperature = 609.4 K and Final Temperature = 325.7 K

b) the change in internal energy

ΔE[tex]_{int[/tex] = nC[tex]_v[/tex]ΔT

here, C[tex]_v[/tex] = ( 5/2 )R

ΔE[tex]_{int[/tex] = 3.10 × ( 5/2 )8.314 × ( 325.7 - 609.4 )

= -18279.78 J

Therefore, the change in internal energy is -18279.78 J

c) the heat lost by the gas

Since its an adiabatic process,

Q = 0

Therefore, heat lost by the gas is zero or 0

d)  the work done on the gas

W = ΔE[tex]_{int[/tex] - Q

= -18279.78 J - 0

W = -18279.78 J

Therefore, the work done on the gas is -18279.78 J

a) The Initial Temperature and Final Temperature of gas are 601.68 K and 321.61 K respectively.

b) The change in internal energy is -18279.78 J.

c) The heat lost by the gas is zero.

d) The work done on the gas is -18279.78 J.

Given data:

The moles of sample is, n = 3.10 mol.

The initial volume of sample is, [tex]V_{1}=0.1550 \;\rm m^{3}[/tex].

The final volume of sample is, [tex]V_{2}=0.742 \;\rm m^{3}[/tex].

The initial pressure of the sample is, [tex]P_{1}=1.00 \;\rm atm[/tex].

(a)

We know that the relation between the pressure and volume for an adiabatic process is as follows,

[tex]P_{1}V_{1}^{\gamma} = P_{2}V_{2}^{\gamma}[/tex]

Here, [tex]\gamma[/tex]  is a adiabatic index. And for air, its value is 1.41.

Solving as,

[tex]P_{2}=P_{1} \times\dfrac{V_{1}^{\gamma}}{V_{2}^{\gamma}}\\\\\\P_{2}=1.00 \times\dfrac{0.1550^{1.41}}{0.742^{1.41}}\\\\\\P_{2} = 0.11166 \;\rm atm[/tex]

Now, calculate the final temperature using the ideal gas equation as,

[tex]P_{2}V_{2}=nRT_{2}\\\\T_{2}= \dfrac{P_{2} \times V_{2}}{nR}\\\\T_{2}= \dfrac{0.11166 \times 10^{5}\times 0.742}{3.10 \times 8.31}\\\\T_{2}=321.61 \;\rm K[/tex]

Similarly, calculate the initial temperature as,

[tex]P_{1}V_{1}=nRT_{1}\\\\T_{1}= \dfrac{P_{1} \times V_{1}}{nR}\\\\T_{1}= \dfrac{1 \times 10^{5}\times 0.1550}{3.10 \times 8.31}\\\\T_{1}=601.68 \;\rm K[/tex]

Thus, we can conclude that the initial and final temperature of the gas is 601.68 K and 321.61 K respectively.

(b)

The change in internal energy is given as,

ΔE = nCΔT

here, C = ( 5/2 )R

ΔE = 3.10 × ( 5/2 )8.314 × ( 325.7 - 609.4 )

      = -18279.78 J

Therefore, the change in internal energy is -18279.78 J.

c)

The heat lost by the gas . Since its an adiabatic process, so there will be no heat interaction.  

Q = 0

Therefore, heat lost by the gas is zero or 0

d)  

The work done on the gas

W = ΔE - Q

W = -18279.78 J - 0

W = -18279.78 J

Therefore, the work done on the gas is -18279.78 J.

Learn more about the adiabatic process here:

https://brainly.com/question/14930930

A mixture of gaseous reactants is put into a cylinder, where a chemical reaction turns them into gaseous products. The cylinder has a piston that moves in or out, as necessary, to keep constant pressure on the mixture of 1 atm. The cylinder is also submerged in a large insulated water bath. The temperature of the water bath is monitored, and it is determined from this data that 133.0 kJ of heat flows into the system during the reaction. The position of the piston is also monitored, and it is determined from the data that the piston does 241.0 kJ of work on the system during the reaction.

a. Does the temperature of the water bath go up or down?
b. Does the piston move in or out?
c. Does heat flow into or out of the gaseous mixture?
d. How much heat flows?

Answers

I feel like it would be B makes the most sense not sure tho

why do you like the full moon ?

Answers

Answer:

The Moon brings perspective. Observing the Moon, and I mean really looking – sitting comfortably, or lying down on a patch of grass and letting her light fill your eyes, it's easy to be reminded of how ancient and everlasting the celestial bodies are. When I do this, it always puts my life into perspective.

Answer:

because it look more impressive than empty dark sky .

No esporte coletivo, um dos principais fatores desenvolvidos é o desenvolvimento social. Qual desses não faz parte das virtudes ensinadas no esporte?

Companheirismo
Humildade
Ser justo (Fair Play)
Vencer independente do que precise ser feito

Answers

Answer:

fair palybtgshsisuehdh

Which graph would be created by a pendulum with the greatest amplitude?

Answers

Answer:

Graph (c) would be created by a pendulum with the greatest amplitude.

Explanation:

The amplitude of a wave is the greatest displacement covered by an object. It refers to the maximum amount of displacement of a particle on the medium from its rest position. It is the distance from rest to crest.

Out of three graphs, the amplitude is greatest in graph 3 as the distance from rest is crest in this case is maximum. Hence, the correct option is (c).

How does the theory of relativity explain the gravity exerted by massive objects?
A. More massive objects create stronger forces of gravity.
B. More massive objects create shallower curves of space-time.
C. More massive objects pull objects from farther away.
D. More massive objects create larger curves of space-time.

Answers

(D)

Explanation:

The more massive an object is, the greater is the curvature that they produce on the space-time around it.

The theory of relativity explain the gravity exerted by massive objects is

more massive objects create larger curves of space-time (option-d).

Do bigger objects exert more gravity?

The term "gravitational force" refers to the attraction between masses. The gravitational force increases in size as the masses get bigger (also called the gravity force). As the distance between masses grows, the gravitational force progressively lessens.

Greater gravitational forces will be used to attract heavier things since the gravitational force is directly proportional to the mass of both interacting objects. Therefore, when two things' respective masses increase, so does their gravitational pull to one another.

To know more about gravity visit:

https://brainly.com/question/4014727

#SPJ2

A flat coil of wire is placed in a uniform magnetic field that is in the y-direction.
The magnetic flux through the coil is maximum if the coil is:_________.
(a) in the XY plane
(b) in either the XY or the YZ plane
(c) in the XZ plane
(d) in any orientation, because it is constant.

Answers

Answer:

The correct answer is c

Explanation:

Flow is defined by

        Ф =  B . A

bold letters indicate vectors.

The magnetic field is directed to the y axis, The area of ​​the coil is represented by a vector normal to the plane of the coil, so to have a flux

                i.i = j.j = k.k = 1

and the tori scalar products are zero

a) If the coil must be in the xy plane so that its normal vector is in the Z axis, so there is no flux

b) if the coil is in the plane yz the normal veto is in the x axis, so the flux is zero

C) If the coil is in XZ, the normal vector points in the y direction, usually the scalar product is one and there is a flux in this configuration

The correct answer is c

the speed of the pulse depends on what?​

Answers

Answer:

The pulse speed depends on the properties of the medium and not on the amplitude or pulse length of the pulse.

Explanation:

Hope this helps.

A 1500 kg car traveling at 20 m/s suddenly runs out of gas while approaching the valley shown in the figure. The alert driver immediately puts the car in neutral so that it will roll.

What will be the car’s speed as it coasts into the gas station on the other side of the valley?

Answers

Answer:

v_f = 17.4 m / s

Explanation:

For this exercise we can use conservation of energy

starting point. On the hill when running out of gas

          Em₀ = K + U = ½ m v₀² + m g y₁

final point. Arriving at the gas station

         Em_f = K + U = ½ m v_f ² + m g y₂

energy is conserved

         Em₀ = Em_f

         ½ m v₀ ² + m g y₁ = ½ m v_f ² + m g y₂

        v_f ² = v₀² + 2g (y₁ -y₂)

         

we calculate

        v_f ² = 20² + 2 9.8  (10 -15)

        v_f = √302

         v_f = 17.4 m / s

Topic: Chapter 19: Some wiggle room
A hummingbird flaps its wings up to 70 times per second, producing a 70 Hz
hum as it flies by. If the speed of sound is 340 m/s, how far does the sound
travel between wing flaps?
= 4.86 m
= 58.9 m
= 0.206 m
= 23,800 m

Answers

Answer:

4.86 m

Explanation:

Given that,

The frequency produced by a humming bird, f = 70 Hz

The speed of sound, v = 340 m/s

We need to find how far does the sound  travel between wing flaps. Let the distance is equal to its wavelength. So,

[tex]v=f\lambda\\\\\lambda=\dfrac{v}{f}\\\\\lambda=\dfrac{340}{70}\\\\\lambda=4.86\ m[/tex]

So, the sound travel 4.86 m between wings flaps.

Can you think of reasons why the charge on each ball decreases over time and where the charges might go

Answers

Answer:

By the principle of corona discharge.

Explanation:

The charge on each ball will decreases over time due to the electrical discharge in air.

According to the principle of corona discharge, when the curvature is small, the discharge of the charge takes placed form the pointed ends.

The working substance of a certain Carnot engine is 1.90 of an ideal
monatomic gas. During the isothermal expansion portion of this engine's
cycle, the volume of the gas doubles, while during the adiabatic expansion
the volume increases by a factor of 5.7. The work output of the engine is
930 in each cycle.
Compute the temperatures of the two reservoirs between which this engine
operates.

Answers

Answer:

Explanation:

The energy for an isothermal expansion can be computed as:

[tex]\mathsf{Q_H =nRTIn (\dfrac{V_b}{V_a})}[/tex] --- (1)

However, we are being told that the volume of the gas is twice itself when undergoing adiabatic expansion. This implies that:

[tex]V_b = 2V_a[/tex]

Equation (1) can be written as:

[tex]\mathtt{Q_H = nRT_H In (2)}[/tex]

Also, in a Carnot engine, the efficiency can be computed as:

[tex]\mathtt{e = 1 - \dfrac{T_L}{T_H}}[/tex]

[tex]e = \dfrac{T_H-T_L}{T_H}[/tex]

In addition to that, for any heat engine, the efficiency e =[tex]\dfrac{W}{Q_H}[/tex]

relating the above two equations together, we have:

[tex]\dfrac{T_H-T_L}{T_H} = \dfrac{W}{Q_H}[/tex]

Making the work done (W) the subject:

[tex]W = Q_H \Big(\dfrac{T_H-T_L}{T_H} \Big)[/tex]

From equation (1):

[tex]\mathsf{W = nRT_HIn(2) \Big(\dfrac{T_H-T_L}{T_H} \Big)}[/tex]

[tex]\mathsf{W = nRIn(2) \Big(T_H-T_L} \Big)}[/tex]

If we consider the adiabatic expansion as well:

[tex]PV^y[/tex] = constant

i.e.

[tex]P_bV_b^y = P_cV_c^y[/tex]

From ideal gas PV = nRT

we can have:

[tex]\dfrac{nRT_H}{V_b}(V_b^y)= \dfrac{nRT_L}{V_c}(V_c^y)[/tex]

[tex]T_H = T_L \Big(\dfrac{V_c}{V_b}\Big)^{y-1}[/tex]

From the question, let us recall  aw we are being informed that:

If the volumes changes by a factor = 5.7

Then, it implies that:

[tex]\Big(\dfrac{V_c}{V_b}\Big) = 5.7[/tex]

[tex]T_H = T_L (5.7)^{y-1}[/tex]

In an ideal monoatomic gas [tex]\gamma = 1.6[/tex]

As such:

[tex]T_H = T_L (5.7)^{1.6-1}[/tex]

[tex]T_H = T_L (5.7)^{0.67}[/tex]

Replacing the value of [tex]T_H = T_L (5.7)^{0.67}[/tex] into equation [tex]\mathsf{W = nRIn(2) \Big(T_H-T_L} \Big)}[/tex]

[tex]\mathsf{W = nRT_L In(2) (5.7 ^{0.67 }-1}})[/tex]

From in the question:

W = 930 J and the moles = 1.90

using 8.314 as constant

Then:

[tex]\mathsf{930 = (1.90)(8.314)T_L In(2) (5.7 ^{0.67 }-1}})[/tex]

[tex]\mathsf{930 = 15.7966\times 1.5315 (T_L )})[/tex]

[tex]\mathsf{T_L= \dfrac{930 }{15.7966\times 1.5315}}[/tex]

[tex]\mathbf{T_L \simeq = 39 \ K}[/tex]

From [tex]T_H = T_L (5.7)^{0.67}[/tex]

[tex]\mathsf{T_H = 39 (5.7)^{0.67}}[/tex]

[tex]\mathbf{T_H \simeq 125K}[/tex]

1. On each of your equipotential maps, draw some electric field lines with arrow heads indicating the direction of the field. (Hint: At what angle do field lines intersect equipotential lines?) Draw sufficient field lines that you can "see" the electric field.

Answers

Answer:

The angle between the electric field lines and the equipotential surface is 90 degree.

Explanation:

The equipotential surfaces are the surface on which the electric potential is same. The work done in moving a charge from one point to another on an equipotential surface is always zero.

The electric field lines are always perpendicular to the equipotential surface.

As

[tex]dV = \overrightarrow{E} . d\overrightarrow{r}\\\\[/tex]

For equipotential surface, dV = 0 so

[tex]0 = \overrightarrow{E} . d\overrightarrow{r}\\\\[/tex]

The dot product of two non zero vectors is zero, if they are perpendicular to each other.

Find the force on a negative charge that is placed midway between two equal positive charges. All charges have the same magnitude.

Answers

Answer: The force on a negative charge that is placed midway between two equal positive charges is zero when all charges have the same magnitude.

Explanation:

Let us assume that

[tex]q_{1} = q_{2} = +q[/tex]

[tex]q_{3} = -q[/tex]

As [tex]q_{3}[/tex] is the negative charge and placed midway between two equal positive charges ([tex]q_{1}[/tex] and [tex]q_{2}[/tex]).

Total distance between [tex]q_{1}[/tex] and [tex]q_{2}[/tex] is 2r. This means that the distance between [tex]q_{1}[/tex] and [tex]q_{3}[/tex], [tex]q_{2}[/tex] and [tex]q_{3}[/tex] = d = r

Now, force action on charge [tex]q_{3}[/tex] due to [tex]q_{1}[/tex] is as follows.

[tex]F_{31} = k(\frac{q_{1} \times q_{3}}{d^{2}})[/tex]

where,

k = electrostatic constant = [tex]9 \times 10^{9} Nm^{2}/C^{2}[/tex]

Substitute the values into above formula as follows.

[tex]F_{31} = k(\frac{q_{1} \times q_{3}}{d^{2}})\\= 9 \times 10^{9} (\frac{q \times (-q)}{r^{2}})\\= - 9 \times 10^{9} (\frac{q^{2}}{r^{2}})[/tex] ... (1)

Similarly, force acting on [tex]q_{3}[/tex] due to [tex]q_{1}[/tex] is as follows.

[tex]F_{32} = k \frac{q_{2}q_{3}}{d^{2}}\\= -9 \times 10^{9} \frac{q^{2}}{r^{2}}\\[/tex]   ... (2)

As both the forces represented in equation (1) and (2) are same and equal in magnitude. This means that the net force acting on charge [tex]q_{3}[/tex] is zero.

Thus, we can conclude that the force on a negative charge that is placed midway between two equal positive charges is zero when all charges have the same magnitude.

A light source radiates 60.0 W of single-wavelength sinusoidal light uniformly in all directions. What is the average intensity of the light from this bulb at a distance of 0.400 m from the bulb

Answers

Answer: [tex]29.85\ W/m^2[/tex]

Explanation:

Given

Power [tex]P=60\ W[/tex]

Distance from the light source [tex]r=0.4\ m[/tex]

Intensity is given by

[tex]I=\dfrac{P}{4\pi r^2}[/tex]

Inserting values

[tex]\Rightarrow I=\dfrac{60}{4\pi (0.4)^2}\\\\\Rightarrow I=\dfrac{60}{2.010}\\\\\Rightarrow I=29.85\ W/m^2[/tex]

Answer:

29.85 W/ m^2

Explanation:

The cannon on a battleship can fire a shell a maximum distance of 33.0 km.
(a) Calculate the initial velocity of the shell.

Answers

Answer:

v = 804.23 m/s

Explanation:

Given that,

The maximum distance covered by a cannon, d = 33 km = 33000 m

We need to find the initial velocity of the shell. Let it is v. It can be calculated using the conservation of energy such that,

[tex]v=\sqrt{2gh} \\\\v=\sqrt{2\times 9.8\times 33000} \\\\v=804.23\ m/s[/tex]

So, the initial velocity of the shell is 804.23 m/s.

Olympus Mons on Mars is the largest volcano in the solar system, at a height of 25 km and with a radius of 309 km. If you are standing on the summit, with what initial velocity would you have to fire a projectile from a cannon horizontally to clear the volcano and land on the surface of Mars

Answers

Answer:

The velocity is 2661.5 m/s.

Explanation:

Radius, horizontal distance, d = 309 km

height, h = 25 km

acceleration due to gravity on moon, g =3.71 m/s^2

Let the time taken is t and the horizontal velocity is u.

horizontal distance = horizontal velocity x time

309 x 1000 = u t .... (1)

Use second equation of motion in vertical direction.

[tex]h = u_yt +0.5 gt^2\\\\25000 = 0 + 0.5\times 3.71\times t^2\\\\t =116.1 s[/tex]  

So, put in (1)

309 x 1000 = u x 116.1

u = 2661.5 m/s

A 49.5-turn circular coil of radius 5.10 cm can be oriented in any direction in a uniform magnetic field having a magnitude of 0.535 T. If the coil carries a current of 26.5 mA, find the magnitude of the maximum possible torque exerted on the coil.

Answers

Answer:

The magnitude of the maximum possible torque exerted on the coil is 5.73 x 10⁻³ Nm

Explanation:

Given;

number of turns of the circular coil, N = 49.5 turns

radius of the coil, r = 5.10 cm = 0.051 m

magnitude of the magnetic field, B = 0.535 T

current in the coil, I = 26.5 mA = 0.0265 A

The magnitude of the maximum possible torque exerted on the coil is calculated as;

τ = NIAB

where;

A is the area of the coil

A = πr² = π(0.051)² = 0.00817 m²

Substitute the given values and solve for the maximum torque

τ = (49.5) x (0.0265) x (0.00817) x (0.535)

τ = 0.00573 Nm

τ = 5.73 x 10⁻³ Nm

Suppose a power plant uses a Carnot engine to generate electricity, using the atmosphere at 300 K as the low-temperature reservoir. Suppose the power plant produces an amount of electric energy with the hot reservoir at 500 K during Day One and then produces the same amount of electric energy with the hot reservoir at 600 K during Day Two. The thermal pollution was:

Answers

Answer: hello your question lacks some vital information below is the complete question

Suppose a power plant uses a Carnot engine to generate electricity, using the atmosphere at 300 K as the low-temperature reservoir. Suppose the power plant produces 1 × 106 J of electricity with the hot reservoir at 500 K during Day One and then produces 1 × 106 J of electricity with the hot reservoir at 600 K during Day Two. The thermal pollution was

answer:

Total thermal pollution = 2.5 * 10^6 J

Explanation:

Low temperature reservoir = 300 K

hot reservoir temperature = 500 K

Electrical energy produced by plant ( W ) = 1 * 10^6 J

lets assume ; Q1 = energy absorbed , Q2 = energy emitted

W = Q1 - Q2  or  Q2 = Q1 - W  ( we will apply this as the formula for determining thermal pollution )

For day 1

T1 = 500k , T2 = 300k

applying Carnot engine formula

W / Q1 = 1 - T2/T1

∴ Q1 = 10^6 / ( 1 - (300/500)) = 2.5 * 10^6 J

thermal pollution ; Q2 = Q1 - W = ( 2.5 * 10^6 - 1 * 10^6 ) = 1.5 * 10^6 J

for Day 2

T1 = 600k,  T2 = 300k

Q1 = 10^6 / ( 1 - (300/600)) = 2 * 10^6 J

Thermal pollution; Q2 = Q1 - W  = 1 * 10^6 J

Therefore the Total thermal pollution =  1 * 10^6  + 1.5 * 10^6  = 2.5 * 10^6 J

Other Questions
who is responsible for the preparation of the financial statement Lavania is studying the growth of a population of fruit flies in her laboratory. After 6 days she had nine more than five times as many fruit flies as when she began the study. If she observes 20 fruit flies on the first day of the study, write and evaluate an expression to find the population of fruit flies Lavania observed after 6 daysa. write an expression for the population of fruit flies Lavania observed after 6 daysb. find the population of fruit flies Lavania observed after 6 days If m2 DOC = 44 and m2 COB = 80,find the measure of the indicated arcin circle o.mCB = [?] which equation represent this relation Find the value of x. PLEASE HELP ASAP!A.4B. 16. 5D. 12 which article of the present constitution deals with the federal executive? explain the power and function of the Federal executive in Nepal Which statement describes the law of conservation of energy?All systems will exchange matter and energy with their surroundings.All systems can exchange energy, but not matter, with their surroundings.Energy cannot be created nor destroyed, but it changes from one form to another.Energy is destroyed in most chemical reactions when new products are formed. Review Question 1 What is meant by deadweight loss? Why does a price ceiling usually result in a deadweight loss? Deadweight loss is a _____________________. A price ceiling results in a deadweight loss when the ceiling price is set ________________ the market clearing price. A. net loss in output; above B. net loss of consumer and producer surplus; below C. net loss in output; below D. net loss of consumer and producer surplus; above Click to select your answer and then click Check Answer. All parts showing I will give brainly.How do you determine if a slope is positive or negative? Los hmsteres tienen 22 cromosomas y sus clulas haploides. Cuntos cromosomas hay en su clula diploide heredera? I need help I don't understand this. \sqrt{2x+1} = 2+\sqrt{x-3} two difference between endocrine and exocrine glandplease give me ans What is the need for satellite communication elaborate what do you mean by occupation?? anxiety: a. is never normal. b. is common of many psychological disorders c. is identical to fear d. is a modern development, unlikely to have roots in human history How many moles of iron is equivalent to 4.45 x 10^22 atoms of iron Read the story description and historical context for the short story "Rules of the Game" and answer the question.Story Description:"Rules of the Game" tells the story of a girl who lives in San Francisco's Chinatown. She learns the strategies of chess but struggles to see eye-to-eye with her motherpossibly her wisest opponent and best teacher. In chess and in life, there are rules and choices. What's your next move?Historical Context:As a result of wars, famine, and political oppression, Chinese immigration to the United States dates back to the mid-1800s. Chinese immigrants came to the United States looking for better economic opportunities so they could provide for their families and send money to their relatives back home. San Francisco became a hub of Chinese culture; however, immigrants still faced many challenges like reduced wages, long work hours, and discrimination.What can you infer about the narrator of "Rules of the Game"? She is a bad competitor. She is a clever chess player. She is a poor decision maker. She is too young for competition. what we're two main reasons that the british granted independence to india? 11. Choose the best answer.A spore is a reproductive structure that contains a haploid cell anda food supplya stylea protective coatinga diploid cell