Answer:
Explanation:
When a falcon is hovering, the force of up thrust is balanced by the weight.
When it begins to fall towards the ground, the weight acts downwards, kinetic friction is upwards, drag is upwards, normal force is upwards, thrust is upwards.
An electron is released from rest at a distance of 9.00 cm from a fixed proton. How fast will the electron be moving when it is 3.00 cm from the proton
Answer:
the speed of the electron at the given position is 106.2 m/s
Explanation:
Given;
initial position of the electron, r = 9 cm = 0.09 m
final position of the electron, r₂ = 3 cm = 0.03 m
let the speed of the electron at the given position = v
The initial potential energy of the electron is calculated as;
[tex]U_i = Fr = \frac{kq^2}{r^2} \times r = \frac{kq^2}{r} \\\\U_i = \frac{(9\times 10^9)(1.602\times 10^{-19})^2}{0.09} \\\\U_i = 2.566 \times 10^{-27} \ J[/tex]
When the electron is 3 cm from the proton, the final potential energy of the electron is calculated as;
[tex]U_f = \frac{kq^2}{r_2} \\\\U_f = [\frac{(9\times 10^9)\times (1.602 \times 10^{-19})^2}{0.03} ]\\\\U_f = 7.669 \times 10^{-27} \ J \\\\\Delta U = U_f -U_i\\\\\Delta U = (7.699\times 10^{-27} \ J ) - (2.566 \times 10^{-27} \ J)\\\\\Delta U = 5.133 \times 10^{-27} \ J[/tex]
Apply the principle of conservation of energy;
ΔK.E = ΔU
[tex]K.E_f -K.E_i = \Delta U\\\\initial \ velocity \ of \ the \ electron = 0\\\\K.E_f - 0 = \Delta U\\\\K.E_f = \Delta U\\\\\frac{1}{2} mv^2 = \Delta U\\\\where;\\\\m \ is \ the \ mass \ of\ the \ electron = 9.1 1 \times 10^{-31} \ kg\\\\v^2 = \frac{ 2 \Delta U}{m} \\\\v = \sqrt{\frac{ 2 \Delta U}{m}} \\\\v = \sqrt{\frac{ 2 (5.133\times 10^{-27})}{9.11\times 10^{-31}}}\\\\v = \sqrt{11268.935} \\\\v = 106.2 \ m/s[/tex]
Therefore, the speed of the electron at the given position is 106.2 m/s
If an object with constant mass is accelerating, what does Newton's second
law imply?
A. It will continue to accelerate until it meets an opposing force.
B. The object is exerting an opposite but equal force.
C. A force must be acting on the object.
D. The object will be difficult to decelerate.
Answer:
C. A force must be acting on the object.
Explanation:
This is due to the action of its momentum direction.
[tex].[/tex]
krichoffs law of current questions
Answer:
Explanation:
Kirchhoff's Current Law, often shortened to KCL, states that “The algebraic sum of all currents entering and exiting a node must equal zero.
#I AM ILLITERATE
a standard bathroom scale is placed on an elevator. A 34 kg boy enters the elevator on the first floor and steps on the scale. What will the scale read (in newtons) when the elevator begins to accelerate upward at 0.4 m/s2
Answer:F = 255 N
Explanation:
It is given that,
Mass of the boy, m = 25 kg
Acceleration of the elevator,
The elevator is accelerating in upward direction. The net force acting on the boy is given by :
g is the acceleration due to gravity
F = 255 N
The scale reading is 255 N as it begins to accelerate upward. hence, this is the required solution.
A cylindrical swimming pool has a radius 2m and depth 1.3m .it is completely filled with salt water of specific gravity 1.03.The atmospheric preassure is 1.013 x 10^5 Pa.
a.calculate the density of salt water.
Answer:
the density of the salt water is 1030 kg/m³
Explanation:
Given;
radius of the cylindrical pool, r = 2 m
depth of the pool, h = 1.3 m
specific gravity of the salt water, γ = 1.03
The atmospheric pressure, P₀ = 1.013 x 10⁵ Pa
Density of fresh water, [tex]\rho _w[/tex] = 1000 kg/m³
The density of the salt water is calculated as;
[tex]Specific \ gravity \ of \ salt\ water \ (\gamma _s_w) = \frac{density \ of \ salt \ water \ (\rho_{sw})}{density \ of \ fresh \ water \ (\rho_{w})} \\\\1.03 = \frac{\rho_{sw}}{1000 \ kg/m^3}\\\\\rho_{sw} = 1.03 \times 1000 \ kg/m^3\\\\\rho_{sw} = 1030 \ kg/m^3[/tex]
Therefore, the density of the salt water is 1030 kg/m³
A 700N marine in basic training climbs a 10m vertical rope at constant speed in 8sec. what is power put
Answer:
875 Watts
Explanation:
P = W/t = mgh/t = 700(10)/8 = 875 Watts
A 0.160 kg glider is moving to the right on a frictionless, horizontal air track with a speed of 0.710 m/s. It has a head-on collision with a 0.296 kg glider that is moving to the left with a speed of 2.23 m/s. Suppose the collision is elastic.
Required:
a. Find the magnitude of the final velocity of the 0.157kg glider.
b. Find the magnitude of the final velocity of the 0.306kg glider.
The masses of the gliders provided in the question differ from the masses mentioned in the "Required" section. I'll use the first masses throughout.
Momentum is conserved, so the total momentum of the system is the same before and after the collision:
m₁ v₁ + m₂ v₂ = m₁ v₁' + m₂ v₂'
==>
(0.160 kg) (0.710 m/s) + (0.296 kg) (-2.23 m/s) = (0.160 kg) v₁' + (0.296 kg) v₂'
==>
-0.546 kg•m/s ≈ (0.160 kg) v₁' + (0.296 kg) v₂'
where v₁' and v₂' are the gliders' respective final velocities. Notice that we take rightward to be positive and leftward to be negative.
Kinetic energy is also conserved, so that
1/2 m₁ v₁² + 1/2 m₂ v₂² = 1/2 m₁ (v₁' )² + 1/2 m₂ (v₂' )²
or
m₁ v₁² + m₂ v₂² = m₁ (v₁' )² + m₂ (v₂' )²
==>
(0.160 kg) (0.710 m/s)² + (0.296 kg) (-2.23 m/s)² = (0.160 kg) (v₁' )² + (0.296 kg) (v₂' )²
==>
1.55 kg•m²/s² ≈ (0.160 kg) (v₁' )² + (0.296 kg) (v₂' )²
Solve for v₁' and v₂'. Using a calculator, you would find two solutions, one of which we throw out because it corresponds exactly to the initial velocities. The desired solution is
v₁' ≈ -3.11 m/s
v₂' ≈ -0.167 m/s
and take the absolute values to get the magnitudes.
If you want to instead use the masses from the "Required" section, you would end up with
v₁' ≈ -3.18 m/s
v₂' ≈ -0.236 m/s
A race car goes from a complete stop at the start line to 150 miles per hour in 5 seconds. What is its acceleration? Show your work.
Answer:
Explanation:
150/5 = 30
30mph per 1 second
If a jet travels 350 m/s, how far will it travel each second?
Answer:
It will travel 350 meters each second.
Explanation:
The unit rate, 350 m/s, tells us that the jet will travel 350 meters per every second elapsed.
Answer:
5.83 seconds
Explanation:
60 seconds in 1 minute
350 meters per second
350/60
=5.83
Earth’s Moon has a diameter of 3,474 km and orbits at an average distance of 384,000 km. At that distance it subtends and angle just slightly larger than half a degree in Earth’s sky. Pluto’s moon Charon has a diameter of 1,186 km and orbits at a distance of 19,600 km from the dwarf planet. Compare the appearance of Charon in Pluto’s skies with the Moon in Earth’s skies. Describe where in the sky Charon would appear as seen from various locations on Pluto.
The reason for arriving at the above solutions is as follows:
The given dimensions and distance from the Earth of the Moon are;
The diameter of the Moon, d = 3,474 km
The average distance of the Moon from the Earth, R = 384,000 km
Required:
The comparison between Charon's appearance in Pluto and the Moon's appearance on Earth Earth
Solution:
The distance of the Moon's travels in an orbit, C = 2·π·R
∴ C = 2 × π × 384,000 km
The angle subtended by the Moon, θ = d/C × 360°
∴ θ = 3,474/(2 × π × 384,000) × 360° ≈ 0.518°
Pluto's moon Charon, has the following parameters;
The diameter of the Charon, d₂ = 1,186 km
The average distance of the Charon from Pluto, R₂ = 19,600 km
Therefore, the distance of the Moon's travels in an orbit, C₂ = 2·π·R₂
∴ C₂ = 2 × π × 19,600 km
The angle subtended by the Moon, θ₂ = d₂/C₂ × 360°
∴ θ₂ = 1,186/(2 × π × 19,900) × 360° ≈ 3.415°
The angle subtended by Charon in Pluto's sky ≈ 3.415°
Charon therefore, appears 7 times larger in Pluto's skies than the Moon's appearance in Earth's skies
Required:
The appearance of Charon as seen from different locations on Pluto
Solution:
Charon is gravitationally locked to Pluto, therefore, the same side of Pluto is faced with the same side of Charon
Therefore;
Charon appears constantly overhead from the side of Pluto locked to CharonCharon appears constantly at the horizon from the poles on either side of the axis of rotation of Pluto and CharonLearn more about Pluto's moon Charon here:
https://brainly.com/question/3920772
https://brainly.com/question/21590852
https://brainly.com/question/17177801
Choose one. 5 points
Use the equation from week 3:
frequency =
wavespeed
wavelength
and the wavelength you found in #3 to calculate the frequency of this photon (remember the speed of
light is 3E8 m/s);
7.6E14 Hz
6.0E14 Hz
4,6E14 Hz
The frequency is 4,6E14 Hz.
What is the frequency?
Frequency is the fee at which modern changes direction in step with 2nd. it's far measured in hertz (Hz), a worldwide unit of degree wherein 1 hertz is identical to 1 cycle in line with 2d. Hertz (Hz) = One hertz is the same as 1 cycle in step with the second. Cycle = One entire wave of alternating present-day voltage.
Frequency describes the number of waves that pass a hard and fast place in a given quantity of time. So if the time it takes for a wave to skip is half of 2d, the frequency is 2 per 2nd. If it takes 1/one hundred of an hour, the frequency is a hundred in step with hour.
Learn more about frequency here:-https://brainly.com/question/254161
#SPJ2
You are to connect resistors R1 andR2, with R1 >R2, to a battery, first individually, then inseries, and then in parallel. Rank those arrangements according tothe amount of current through the battery, greatest first. (Useonly the symbols > or =, for exampleseries>R1=R2>parallel.)
Answer:
The current is more in the parallel combination than in the series combination.
Explanation:
two resistances, R1 and R2 are connected to a battery of voltage V.
When they are in series,
R = R1 + R2
In series combination, the current is same in both the resistors, and it is given by Ohm's law.
V = I (R1 + R2)
[tex]I = \frac{V}{R_1 + R_2}[/tex]..... (1)
When they are connected in parallel.
the voltage is same in each resistor.
The effective resistance is R.
[tex]R = \frac{R_1R_2}{R_1 + R_2}[/tex]
So, the current is
[tex]I = \frac{V(R_1+R_2)}{R_1 R_2}[/tex]..... (2)
So, the current is more is the parallel combination.
Define wave length as applied to wave motion
Answer: Wavelength can be defined as the distance between two successive crests or troughs of a wave. It is measured in the direction of the wave.
Explanation:
Wavelength refers to the length or distance between two identical points of neighboring cycles of a wave signal traveling in space or in any physical medium. ... The wavelength of a signal is inversely proportional to its frequency, that is, the higher the frequency, the shorter the wavelength.
Do you believe in ghost
Answer:
well its about our thinking but i do believe in ghost a little
Light of a given wavelength is used to illuminate the surface of a metal, however, no photoelectrons are emitted. In order to cause electrons to be ejected from the surface of this metal you should: ___________
a. use light of the same wavelength but increase its intensity.
b. use light of a shorter wavelength.
c. use light of the same wavelength but decrease its intensity.
d. use light of a longer wavelength.
Answer:
use light of the same wavelength but decrease it's intensity
Choose the appropriate explanation how such a low value is possible given Saturn's large mass - 100 times that of Earth.
a. This low value is possible because the magnetic field of Saturn is so strong.
b. This low value is possible because the magnetic field of Saturn is so weak.
c. This low value is possible because the density of Saturn is so high.
d. This low value is possible because the density of Saturn is so low.
Answer:
Explanation:
That is an amazing fact.
The minus sign is what you have to pay attention to. The earth has a mass of 100 times that of Saturn. As someone on here once noted, Saturn has such a low density that it would float in water.
The answer is D
12. A concave lens has a focal length of 10 cm. An object 2.5 cm high is placed 30 cm from the lens. Determine the position and size of the image. (3)
Answer:
I think 9.5
Explanation:
............
A man standing in an elevator holds a spring scale with a load of 5 kg suspended from it. What would be the reading of the scale, if the elevator is accelerating downward with an acceleration 3.8 m/s?.
Answer:
3.1 kg
Explanation:
Applying,
R = m(g-a)..................... Equation 1
Where R = weight of the scale when the elevator is coming down, a = acceleration of the elevator, g = acceleration due to gravith.
From the question,
Given: m = 5 kg, a = 3.8 m/s²
Constant: g = 9.8 m/s²
Substitute these values into equation 1
R = 5(9.8-3.8)
R = 5(6)
R = 30 N
Hence the spring scale is
m' = R/g
m' = 30/9.8
m' = 3.1 kg
A block of mass 0.260 kg is placed on top of a light, vertical spring of force constant 5 200 N/m and pushed downward so that the spring is compressed by 0.090 m. After the block is released from rest, it travels upward and then leaves the spring. To what maximum height above the point of release does it rise
After being released, the restoring force exerted by the spring performs
1/2 (5200 N/m) (0.090 m)² = 12.06 J
of work on the block. At the same time, the block's weight performs
- (0.260 kg) g (0.090 m) ≈ -0.229 J
of work. Then the total work done on the block is about
W ≈ 11.83 J
The block accelerates to a speed v such that, by the work-energy theorem,
W = ∆K ==> 11.83 J = 1/2 (0.260 kg) v ² ==> v ≈ 9.54 m/s
Past the equilibrium point, the spring no longer exerts a force on the block, and the only force acting on it is due to its weight, hence it has a downward acceleration of magnitude g. At its highest point, the block has zero velocity, so that
0² - v ² = -2gy
where y is the maximum height. Solving for y gives
y = v ²/(2g) ≈ 4.64 m
explain why our sweat is salty?
Answer:
Sweat also contains ammonia and urea, which are produced by the body when it breaks down proteins from the foods you eat.
Hope this helps..
Electromagnetic radiation with a wavelength of 525 nm appears as green light to the human eye. Calculate the frequency of this light. Be sure to include units in your answer.
Answer:
5.71×10¹⁴ Hz
Explanation:
Applying,
v = λf................. Equation 1
Where v = speed of the electromagnetic radiation, λ = wavelength of the electromagnetic radiation, f = frequency
make f the subject of the equation
f = v/λ............. Equation 2
From the question,
Given: λ = 525 nm = 5.25×10⁻⁷ m,
Constant: Speed of electromagnetic wave (v) = 3.0×10⁸ m/s
Substitute these values into equation 2
f = (3.0×10⁸)/(5.25×10⁻⁷)
f = 5.71×10¹⁴ Hz
Hence the frequency of light is 5.71×10¹⁴ Hz
S.I unit for distance =______
(A) m (B)cm
(c) km (d) mm
Answer:
opinion a
Explanation:
the si units of distance is metre (m)
Answer:
A
Explanation:
Good evening everyone Help me i n my hw ,The wall of cinema hall are covered with sound absorbing materials. Why?Answer it ASAP.Good day
what do you mean about it
Chameleons catch insects with their tongues, which they can rapidly extend to great lengths. In a typical strike, the chameleon's tongue accelerates at a remarkable 220 m/s^2 for 20 msms, then travels at constant speed for another 30 ms.
Required:
During this total time of 50 ms, 1/20 of a second, how far does the tongue reach?
Solution :
We know,
Distance,
[tex]$S=ut+\frac{1}{2}at^2$[/tex]
[tex]$S=ut+0.5(a)(t)^2$[/tex]
For the first 20 ms,
[tex]$S=0+0.5(220)(0.020)^2$[/tex]
S = 0.044 m
In the remaining 30 ms, it has constant velocity.
[tex]$v=u+at$[/tex]
[tex]$v=0+(220)(0.020)[/tex]
v = 4.4 m/s
Therefore,
[tex]$S=ut+0.5(a)(t)^2$[/tex]
[tex]$S'=4.4 \times 0.030[/tex]
S' = 0.132 m
So, the required distance is = S + S'
= 0.044 + 0.132
= 0.176 m
Therefore, the tongue can reach = 0.176 m or 17.6 cm
Answer:
The total distance is 0.176 m.
Explanation:
For t = 0 s to t = 20 ms
initial velocity, u = 0
acceleration, a = 220 m/s^2
time, t = 20 ms
Let the final speed is v.
Use first equation of motion
v = u + at
v = 0 + 220 x 0.02 = 4.4 m/s
Let the distance is s.
Use second equation of motion
[tex]s = u t + 0.5 at^2\\\\s = 0 + 0.5 \times 220 \times 0.02\times 0.02\\\\s = 0.044 m[/tex]
Now the distance is
s' = v x t
s' = 4.4 x 0.03 = 0.132 m
The total distance is
S = s + s' = 0.044 + 0.132 = 0.176 m
potential diffetence
Answer:
6v
Explanation:
V=IR
V= 2* 3
V= 6 volts
In a photoelectric effect experiment, it is observed that violet light does not eject electrons from a particular metal. Next, red light with the same intensity is incident on the same metal. Which result is possible
Answer:
No ejection of photo electron takes place.
Explanation:
When a photon of suitable energy falls on cathode, then the photoelectrons is emitted from the cathode. This phenomenon is called photo electric effect.
The minimum energy required to just eject an electron is called work function.
The photo electric equation is
E = W + KE
where, E is the incident energy, W is the work function and KE is the kinetic energy.
W = h f
where. h is the Plank's constant and f is the threshold frequency.
Now, when the violet light is falling, no electrons is ejected. When the red light is falling, whose frequency is less than the violet light, then again no photo electron is ejected from the metal surface.
What is the volume of a metal block 3cm long by 2cm wide by 4cm high? What would be the volume of a block twice as long, wide, and high?
Answer:
Volume of a metal block = 24 cm^3
Volume of a block twice as long, wide and high = 192 cm^3
Explanation:
Volume of a block is measured in l*w*h and in the first block, the sides are 3, 2 and 4 and 3*2*4 = 24
Second block, just double each of the lengths to get 6*4*8 = 192
An electron is moving at speed of 6.3 x 10^4 m/s in a circular path of radius of 1.7 cm inside a solenoid the magnetic field of the solenoid is perpendicular to the plane of the electron's path. Find its relevatn motion.
Answer:
Here, m=9×10
−31
kg,
q=1.6×10
−19
C,v=3×10
7
ms
−1
,
b=6×10
−4
T
r=
qB
mv
=
(1.6×10
−19
)(6×10
−4
)
(9×10
−31
)×(3×10
7
)
=0.28m
v=
2πr
v
=
2πm
Bq
=
2×(22/7)×9×10
−31
(6×10
−4
)×(1.6×10
−19
)
=1.7×10
7
Hz
Ek=
2
1
mv
2
=
2
1
×(9×10
−31
)×(3×10
7
)
2
J
=40.5×10
−17
J=
1.6×10
−16
40.5×10
−17
keV
=2.53keV
elastic wire extend by 1.ocm when a load on 20g range from It, what additional load will it be required Cause the futher extension of 2.0cm
Answer:
40g
Explanation:
20g range > 1.0cm
Therefore,
40g range > 2.0cm
Two different galvanometers G1 and G2, have internal resistances r1and r2. The galvanometers G1 and G2 require the same current IC1=IC2 for a full-scale deflection of their pointers. These galvanometers G1 and G2 are used to build lab-made ammeters A1 and A2 . Both ammeters A1 and A2 have the same maximum scale reading Imax1=Imax2=Imax. To build A1 ,shunt resistor of resistance Rsh1is used and to build A2 , shunt resistor of resistance Rsh2 is used. The value of these shunt resistor resistances are such that: Rsh1=3Rsh2. What is the ratio oftheir internal resistances: r1:r2?
Answer:
there are 3 photos attached. so check
Explanation:
