Answer:
43994
Explanation:
Hope this helps!
The equation of damped oscillations is given in the form x=0.05e^-0.25sin½πt (m). Find the velocity of an oscillating point at the moments of time: 0, T, 2T, 3T and 4T.
Explanation:
The logarithmic damping decrement of a mathematical pendulum is DeltaT=0.5. How will the amplitude of oscillations decrease during one full oscillation of the pendulum
Consider a sample containing 1.70 mol of an ideal diatomic gas.
(a) Assuming the molecules rotate but do not vibrate, find the total heat capacity of the sample at constant volume. nCv = J/K
(b) Assuming the molecules rotate but do not vibrate, find the total heat capacity of the sample at constant pressure. nCp = J/K
(c) Assuming the molecules both rotate and vibrate, find the total heat capacity of the sample at constant volume. nCv = J/K
(d) Assuming the molecules both rotate and vibrate, find the total heat capacity of the sample at constant pressure. nCp = J/K
I don't know
because I don't know
If you exert a force of 5 N into a nutcracker, and it outputs a force of 20 N, what is the mechanical advantage of the nutcracker. Show formula PLSSS HELPPPP!!! i'll make you brainliest
Answer: 4
Explanation:
MA = output force / input force
MA = 20 / 5
MA = 4
Hope this helps. Please mark brainliest.
A hockey puck is sliding across the ice with an initial velocity of 25 m/s. If the coefficient of friction between the hockey puck and the ice is 0.08, how much time (in seconds) will it take before the hockey puck slides to a stop
Answer: 31.89seconds
Explanation:
Based on the information given, we are meant to calculate deceleration which will be:
t = V/a
where, a = mg
Therefore, t = V/mg
t = 25/0.08 × 9.8
t = 25/0.784
t = 31.89seconds
Therefore, the time that it will take before the hockey puck slides to a stop is 31.89seconds.
The power in an electrical circuit is given by the equation P= RR, where /is the current flowing through the circuit and Ris the resistance of the circuit. What is the current in a circuit that has a resistance of 100 ohms and a power of 15 watts?
[pleas ee helpppp)
I= 0.39 A
OPTION B is the correct answer.
A force of 3 newtons moves a 10 kilogram mass horizontally a distance of 3 meters. The mass does not slow down or speed up as it moves. Which of the following must be true?
a) 9 joules of kinetic energy were produced
b) 9 joules of gravitational potential energy were produced
c) 9 joules of heat energy were produced
d) 9 joules of kinetic energy and heat were produced
Answer:
9 joules of heat energy was produced
Explanation: there is no acceleration therefore its not a kinetic energy
Energy= force × distance
= 3×3
=9
A positively charged plastic ruler is brought close to a piece paper resting on the desk. The piece of paper was initially neutral. When the ruler was brought closer, the paper is attracted to the ruler. The surface of the paper became charged through:_________
Answer: static electricity
Explanation:
When the plastic ruler is rubbed, friction opposes the motion and causes the transfer of electron from one surface to another such that plastic becomes negatively charged. When ruler is brought nearer to the paper, it induces the positive charge in the piece of paper.
Calculating Acceleration
Initial
velocity
Time to travel
0.25 m
Final
velocity
Acceleration
Time to travel
0.50 m
# of
washers
11
(m/s)
V2
(m/s)
ti
(s)
t₂
(s)
a = (v2 - v4)/(t2-tı)
(m/s)
1
0.11
0.28
2.23
3.13
0.19
2
0.13
0.36
1.92
2.61
The acceleration of the car with two washers added to the string would be
I can not even read this question.
What are you trying to even say?
The acceleration of the car with two (2) washers added is equal to 0.33 [tex]m/s^2[/tex].
Given the following data:
Initial velocity = 0.13 m/s.Final velocity = 0.36 m/s.Initial time = 1.92 seconds.Final time = 2.61 seconds.What is an acceleration?An acceleration can be defined as the rate of change of velocity of an object with respect to time and it is measured in meter per seconds square.
How to calculate average acceleration.In Science, the average acceleration of an object is calculated by subtracting its initial velocity from the final velocity and dividing by the change in time for the given interval.
Mathematically, average acceleration is given by this formula:
[tex]a = \frac{V\;-\;U}{t_f-t_i}[/tex]
Where:
V is the final velocity.U is the initial velocity.[tex]t_i[/tex]initial time measured in seconds.[tex]t_f[/tex] final time measured in seconds.Substituting the given parameters into the formula, we have;
[tex]a = \frac{0.36\;-\;0.13}{2.61\;-\;1.92}\\\\a=\frac{0.23}{0.69}[/tex]
a = 0.33 [tex]m/s^2[/tex]
Read more on acceleration here: brainly.com/question/24728358
How can i prove the conservation of mechanical energy?
Answer:
We can also prove the conservation of mechanical energy of a freely falling body by the work-energy theorem, which states that change in kinetic energy of a body is equal to work done on it. i.e. W=ΔK. And ΔE=ΔK+ΔU. Hence the mechanical energy of the body is conserved
Explanation:
what is the difference between VELOCITY and SPEED?
Answer:
Speed is the time rate at which an object is moving along a path, while velocity is the rate and direction of an object's movement. Put another way, speed is a scalar value, while velocity is a vector. ... In its simplest form, average velocity is calculated by dividing change in position (Δr) by change in time (Δt).
Explanation:
2. The given graph shows that the object is
(a) in non-uniform motion
(b) in uniform motion
(c) at rest
(d) in an oscillatory motion.
distance
time
Answer:
(c) at rest
Explanation:
Given
See attachment for the distance time graph
Required
What does the graph illustrate?
From the graph, we can see that the line of distance is a horizontal line.
This suggests that a time increases, the distance remains unchanged
When distance remains unchanged over time, then it means the object is at rest.
Hence, (c) is correct
Trong máy phát điện xoay chiều ba pha khi tổng điện áp tức thời của cuộn 1,2 là e1+e2=120V thì điện áp tức thời của cuộn 3 là
Answer:
I just noticd i dont speak this launguage
Explanation:
please help very easy 5th grade work giving brainliest
Answer:
the answer is option B because opposit sides of the magnets attract each other
From the top of the leaning tower of Pisa, a steel ball is thrown vertically downwards with a speed of 3.00 m/s. if the height of the tower is 200 m, how long will it take for the ball to hit the ground? Ignore air resistance.
Answer:
66,7 seconds
Explanation:
the formula for height/distance is : S=v.t
The viscid silk produced by the European garden spider (Araneus diadematus) has a resilience of 0.35. If 10.0 J of work are done on the silk to stretch it out, how many Joules of work are released as thermal energy as it relaxes?
Answer: The energy released as thermal energy is 6.5 J
Explanation:
Energy stored by the spider when it relaxes is given by:
[tex]E_o=\text{Resilience}\times \text{Work}[/tex]
We are given:
Resilience = 0.35
Work done = 10.0 J
Putting values in above equation, we get:
[tex]E_o=0.35\times 10\\\\E_o=3.5J[/tex]
Energy released at thermal energy is the difference between the work done and the energy it takes to relaxes, which is given by the equation:
[tex]E_T=\text{Work done}-E_o[/tex]
Putting values in above equation, we get:
[tex]E_T=(10-3.5)=6.5J[/tex]
Hence, the energy released as thermal energy is 6.5 J
The energy released as thermal energy when 10 J of work is done to stretch silk will be 6.5 J
What is thermal energy?Thermal energy refers to the energy contained within a system that is responsible for its temperature. Heat is the flow of thermal energy.
Energy stored by the spider when it relaxes is given by:
[tex]\rm E_o=Resilience \ \times Work[/tex]
We are given:
Resilience = 0.35
Work done = 10.0 J
Putting values in above equation, we get:
[tex]\rm E_o=0.35\times 10[/tex]
[tex]E_o=3.5\ J[/tex]
Energy released at thermal energy is the difference between the work done and the energy it takes to relaxes, which is given by the equation:
[tex]E_T=\rm Work done -E_o[/tex]
Putting values in above equation, we get:
[tex]E_T=(10-3.5)=6.5\ J[/tex]
Hence, the energy released as thermal energy is 6.5 J
To know more about thermal energy follow
https://brainly.com/question/19666326
What happens in the gray zone between solid and liquid?-,-
According to Newton’s law of universal gravitation, which statements are true?
A 5 kg box drops a distance of 10 m to the ground. If 70% of the initial potential energy goes into increasing the internal energy of the box, determine the magnitude of the increase.
Answer:
Explanation:
From the given information:
The initial PE [tex](PE)_i[/tex] = m×g×h
= 5 kg × 9.81 m/s² × 10 m
= 490.5 J
The change in Potential energy P.E of the box is:
ΔP.E = [tex]P.E_f -P.E_i[/tex]
ΔP.E = 0 - [tex](PE)_i[/tex]
ΔP.E = [tex]-P.E_i[/tex]
If we take a look at conservation of total energy for determining the change in the internal energy of the box;
[tex]\Delta P.E + \Delta K.E + \Delta U = 0[/tex]
[tex]\Delta U = -\Delta P.E - \Delta K.E[/tex]
this can be re-written as:
[tex]\Delta U =- (-\Delta P.E_i) - \Delta K.E[/tex]
Here, K.E = 0
Also, 70% goes into raising the internal energy for the box;
Thus,
[tex]\Delta U =(70\%) \Delta P.E_i-0[/tex]
[tex]\Delta U =(0.70) (490.5)[/tex]
ΔU = 343.35 J
Thus, the magnitude of the increase is = 343.35 J
Calculate the Combined resistance of the Circuit voltage across each resistor Current Passing through each resistor of 6,8,12ohms
Answer:
Sorry I don't know the answer
A magnetic field of 0.276 T exists in the region enclosed by a solenoid that has 517 turns and a diameter of 10.5 cm. Within what period of time must the field be reduced to zero if the average magnitude of the induced emf within the coil during this time interval is to be 12.6 kV
Answer:
The period the field must be reduced to zero is 9.81 x 10⁻⁵ s
Explanation:
Given;
initial value of the magnetic field, B₁ = 0.276 T
number of turns of the solenoid, N = 517 turns
diameter of the solenoid, d = 10.5 cm = 0.105 m
induced emf, = 12.6 kV = 12,600 V
when the field becomes zero, then the final magnetic field value, B₂ = 0
The induced emf is given by Faraday's law;
[tex]emf = -\frac{NA\Delta B}{t} \\\\emf = -\frac{NA (B_2 -B_1)}{t} \\\\t = -\frac{NA (B_2 -B_1)}{emf}\\\\t = \frac{NA (B_1 -B_2)}{emf}\\\\where;\\\\t \ is \ the \ time \ when \ B = 0 \ \ (i.e\ B_2 = 0)\\\\A \ is \ the \ area \ of \ the \ coil\\\\A = \frac{\pi d^2}{4} = \frac{\pi (0.105)^2}{4} = 0.00866 \ m^2\\\\t= \frac{(517) \times (0.00866)\times (0.276 -0)}{12,600}\\\\t = 9.81 \times 10^{-5} \ s[/tex]
Therefore, the period the field must be reduced to zero is 9.81 x 10⁻⁵ s
From 2 King 6:1-6, one of the disciples of Elisha was cutting a tree and the ax head fell into the water. While we do not know how high the ax head was when it fell into the water, we will work through a physics example of the ax head's vertical motion as if it were dropped into the water. ( Due date 09/07)
Write your name and date. The due date of this assignment is the height the ax head falls from in meters into the water. For example, if the due date is July 15, then the ax head fell 15 meters to the water.
Write Newton’s 2nd Law in Equation Form.
Write the quantity and units of average gravitational acceleration on the surface of Earth.
Given the ax head mentioned in the opening portion with the height being equal in numerical value of the due day of this assignment. How long does it take for the ax to fall to the river surface?
Compute the final speed of the ax when it hits the water.
Answer:
time of fall is 1.75 s and the velocity with which it strikes the water is 17.15 m/s.
Explanation:
Height, h = 15 m
Newton's second law
Force = mass x acceleration
The unit of gravitational force is Newton and the value is m x g.
where, m is the mas and g is the acceleration due to gravity.
Let the time of fall is t.
Use second equation of motion
[tex]s= u t +0.5 at^2\\\\15 = 0 +0.5\times 9.8\times t^{2}\\\\t = 1.75 s[/tex]
Let the final speed is v.
Use third equation of motion
[tex]v^2 = u^2 + 2 a s\\\\v^2 = 0 + 2 \times 9.8\times 15\\\\v =17.15 m/s[/tex]
An electric device, which heats water by immersing a resistance wire in the water, generates 20 cal of heat
per second when an electric potential difference of 6 V is placed across its leads. What is the resistance in Ω
of the heater wire? (Note: 1 cal = 4.186 J)
Select one:
a. 0.86
b. 0.17
c. 0.29
d. 0.43
Answer:
1 cal/s =4.184w
p=50 cal/s =2093w
v=12v
P = V*I
I =P/V
I = 17.43 A
P =1²*R
R = P/I²
R = 0.68A mass of 4 kg is traveling over a quarter circular ramp with a radius of 10 meters. At the bottom of the incline the mass is moving at 21.3 m/s and at the top of the incline the mass is moving at 2.8 m/s. What is the work done by all non-conservative force in Joules?
Answer:
499.7 J
Explanation:
Since total mechanical energy is conserved,
U₁ + K₁ + W₁ = U₂ + K₂ + W₂ where U₁ = potential energy at bottom of incline = mgh₁, K₁ = kinetic energy at bottom of incline = 1/2mv₁² and W₁ = work done by friction at bottom of incline, and U₂ = potential energy at top of incline = mgh₂, K₁ = kinetic energy at top of incline = 1/2mv₂² and W₂ = work done by friction at top of incline. m = mass = 4 kg, h₁ = 0 m, v₁ = 21.3 m/s, W₁ = 0 J, h₂ = radius of circular ramp = 10 m, v₂ = 2.8 m/s, W₂ = unknown.
So, U₁ + K₁ + W₁ = U₂ + K₂ + W₂
mgh₁ + 1/2mv₁² + W₁ = mgh₂ + 1/2mv₂² + W₂
Substituting the values of the variables into the equation, we have
mgh₁ + 1/2mv₁² + W₁ = mgh₂ + 1/2mv₂² + W₂
4 kg × 9.8 m/s²(0) + 1/2 × 4 kg × (21.3 m/s)² + 0 = 4 kg × 9.8 m/s² × 10 m + 1/2 × 4 kg × (2.8 m/s)² + W₂
0 + 2 kg × 453.69 m²/s² = 392 kgm²/s² + 2 kg × 7.84 m²/s² + W₂
907.38 kgm²/s² = 392 kgm²/s² + 15.68 kgm²/s² + W₂
907.38 kgm²/s² = 407.68 kgm²/s² + W₂
W₂ = 907.38 kgm²/s² - 407.68 kgm²/s²
W₂ = 499.7 kgm²/s²
W₂ = 499.7 J
Since friction is a non-conservative force, the work done by all the non-conservative forces is thus W₂ = 499.7 J
An astronaut throws a wrench in interstellar space. How much force is required to keep the wrench moving continuously with constant velocity?
A.
a force equal to its weight on Earth
B.
a force equal to zero
C.
a force equal to half of its weight on Earth
D.
a force equal to double its weight on Earth
Answer:
0 N
Explanation:
This is a trick question, the mass of the wrench would be 0 due to it being in space and has no gravitational pull to weight it down. And since acceleration is defined as the rate and change of velocity with no respect of time and the wrench is moving at a constant velocity, that means the velocity is 0. and since F = m*a it would be F = 0 * 0 = 0 N
A balloon pops, making a loud noise that startles you. What kind of energy best describes this experience?
A. Thermal Energy
B. Sound Energy
C. Gravitational Energy
D. Radiant Energy
how do you use the coefficient to calculate the number of atoms in each molecule?
Answer:
To find out the number of atoms: MULTIPLY all the SUBSCRIPTS in the molecule by the COEFFICIENT. (This will give you the number of atoms of each element.)
Explanation:
How much power does it take to lift 70.0 N to 5.0 m high in 5.00 s?
Answer:
Power = 70 W
Explanation:
Given that,
Force, F = 70 N
Height, h = 5 m
Time, t = 5 s
We need to find the power of the object. We know that,
Power = work done/time
Put all the values,
[tex]P=\dfrac{Fd}{t}\\\\P=\dfrac{70\times 5}{5}\\\\P=70\ W[/tex]
So, the required power is 70 W.
PLEASE HELP ME WITH THIS ONE QUESTION
The half-life of Barium-139 is 4.96 x 10^3 seconds. A sample contains 3.21 x 10^17 nuclei. What is the decay constant for this decay?
A) 1.67 x 10^-4 s^-1
B) 5.43 x 10^-4 s^-1
C) 1.40 x 10^-4 s^-1
D) 2.22 x 10^-4 s^-1
OPTION C is the correct answer.
A laser emits a single 3.0-ms pulse of light that has a frequency of 2.83E11 Hz and a total power of 65000 W. How many photons are in the pulse? Please provide all equations and work.
6.0E23
1.0E24
2.4E25
3.6E25
4.8E26
Answer:
The number of photons in the pulse is 1.04 x 10²⁴
Explanation:
Given;
frequency of the emitted photons, f = 2.83 x 10¹¹ Hz
duration of the incident light, t = 3 ms = 3 x 10⁻³ s
power of the incident light, P = 65,000 W
The energy of each photon emitted is calculated as;
E = hf
where;
h is Planck's constant, = 6.626 x 10⁻³⁴ Js
E = 6.626 x 10⁻³⁴ x 2.83 x 10¹¹
E = 1.875 x 10⁻²² J
let the number of photons in the pulse = n
n(E)= Power x time
[tex]n = \frac{Pt}{E} \\\\n = \frac{65,000 \times 3\times 10^{-3}}{1.875 \times 10^{-22}} \\\\n = 1.04 \times 10^{24} \ photons[/tex]
reviews the general principles in this problem. A projectile is launched from ground level at an angle of 13.0 ° above the horizontal. It returns to ground level. To what value should the launch angle be adjusted, without changing the launch speed, so that the range doubles?
Answer: θ would equal approximately 28.7°
This is a kinematics problem, where one is only given the theta value 13.0° in regards to the range; thus, the problem is testing one's understanding of the relationships between the variables.
Range (aka x) = (v₀ sin (2θ₀))/g, where θ₀ = 13.0°
Now if we multiply the range by 2, we get:
2x = 2((v₀ sin (2θ₀))/g) → to verbalize, if range equates to (v₀ sin (2θ₀))/g, and doubling the range equals twice the product value, then:
2θ = sin⁻¹(2sin(2(13.0° )) = sin⁻¹(2(0.76255845048)) = sin⁻¹ (1.52511690096) = 57.35560850015109°/2 = θ
Thus, θ = 28.67780425
It's been awhile since I did this; though I hope it helped!