A large water tank with cross sectional area A and height of h is filled to the top with water (density= rho). There is a hole of cross sectional area a located at the bottom of the tank. The velocity of the water exiting the small hole is

The value of R so that the response is critically damped using the equation is 25.0Ω.

Farads is the unit of measure for capacitance, which is the amount of electrical charge stored for a given voltage. Farads can be used to measure the amount of energy stored in a capacitor, which is made up of two conductive plates separated by an insulating material. The higher the capacitance, the more energy can be stored in a given capacitor. Farads are named after Michael Faraday, the British scientist who discovered the relationship between electricity and magnetism.

The resonant frequency of an RLC circuit is given by the equation:
ω_r=1/sqrt(LC)
where ω_r is the resonant frequency in rad/s, L is the inductance in Henries, and C is the capacitance in Farads.
Given the resonant frequency of 5000 rad/s and the inductance of 10 mH, we can calculate the capacitance as follows:
C=1/(ω_r^2*L)
C=1/(5000^2*0.01)
C=4.00μF
We can find the value of R so that the response is critically damped using the equation:
R=2*sqrt(L/C)
R=2*sqrt(0.01/4.00)
R=25.0Ω

To learn more about Farads
https://brainly.com/question/24175851
#SPJ1

Answer:

decreases

Explanation:

The thermal energy of the gob decreases by heating the air around the gob and the mold in which the bottle is made

The increase in mass of the space station has no effect on the field strength, and the increase in orbital radium decreases the field strength

What is Earth's Gravitation Field?

Earth's gravitation field is the force any object experiences due to the gravitational pull by earth. It's formula is given below where G is the force, m is the mass of earth and r is radius of distance.

As seen through the formula, the gravitation field strength is only depend on earth's mass which is constant and radius of the distance. Hence, the increase in mass of the space station has no effect on the field strength, and the increase in orbital radium decreases the field strength.

To learn more about gravitation from the given link

https://brainly.com/question/3009841

#SPJ1

When a white dwarf acquires enough mass for its carbon interior to start fusing, a white dwarf supernova results.

The white dwarf entirely explodes as the star's fusion starts nearly immediately throughout the entire star. When iron is produced during fusion in a star's core, a "massive stellar supernova" results. If a white dwarf in a near binary system acquires enough mass to surpass the "white dwarf limit (1.4 solar masses)," it will erupt as a supernova. The absence of hydrogen characteristics in type I supernovae's spectra at maximum luminosity is a crucial identifying trait. The remnant core of a low-mass star known as a white dwarf is protected from the force of gravity by electron degeneracy pressure. The mass of the Sun is often condensed into a body no bigger than Earth in a white dwarf.

to know more about white dwarf please visit.

https://brainly.com/question/25872293

#SPJ4

The reactive power of the branch (Qb) can be calculated from its voltage and current 676.16 VA.

Reactive power is the power in an AC circuit that is required to establish and maintain a voltage across a load. It is associated with the storage and release of energy in the form of electric and magnetic fields. Reactive power does not contribute to the actual work output of a system and is measured in Volt-amperes reactive (VARs). Power factor is a measure of reactive power relative to the total power in a system.

Source frequency = 60 Hz
Generator impedance = 0 W
Circuit:
Vg = 170 V
R1 = 10 Ω
R2 = 20 Ω
Zb = 20 + j10 Ω

The current flowing through the generator (Ig) and the branch (Ib) can be calculated from Ohm's Law:
Ig = Vg/R1 + Vg/R2 = 170/10 + 170/20 = 17 A
Ib = Ig - Vg/Zb = 17 - 170/(20 + j10) = 17 - 16.4 + j4.4 = 0.6 + j4.4 A
Since Ib is a complex number, we can find its magnitude (|Ib|) and angle (θ):
|Ib| = √(0.6² + 4.4²) = 4.46 A
θ = tan⁻¹(4.4/0.6) = 80.16°
The voltage across the branch (Vb-n) can be calculated using Ohm's Law:
Vb-n = Ib × Zb = (0.6 + j4.4) × (20 + j10) = -8.4 + j74.4 V
The apparent power of the branch (Sb) can be calculated from its voltage and current:
Sb = Vb-n × Ib* = (-8.4 + j74.4) × (0.6 - j4.4) = -45.48 + j367.04 VA
The real power of the branch (Pb) can be calculated from its voltage and current:
Pb = Vb-n × Ib = (-8.4 + j74.4) × (0.6 + j4.4) = -45.48 - j367.04 W
The reactive power of the branch (Qb) can be calculated from its voltage and current:
Qb = Vb-n × Ib* = (-8.4 + j74.4) × (0.6 - j4.4) = 676.16 VA

To learn more about reactive power
https://brainly.com/question/23230296
#SPJ4

Mathematically, F is1.56 represents the resulting force of friction on the block. The Frictioval force's mathematical equation is typically represented as F is uN.

Explanation:

Mathematically, F=1.56 represents the resulting force of friction on the block.

The Frictioval force's mathematical equation is typically represented as F=uN.

u equals the friction coefficient.

N is normal force.

frictional force

As a result, the force of friction on the F=10.4*0.15 F=1.56

To learn more about Force of friction refer to:

https://brainly.com/question/24386803

#SPJ1

The experimental procedures that will allow the students to determine both of these relationships is option E:

The formula  F = IL x B calculates the magnetic force acting through a magnetic field on a current-carrying wire. The magnetic field acts on a wire when a current is conducted through it in a direction that is perpendicular to both the magnetic force.

By increasing the amount of current flowing through the wire, the magnetic field's strength can be enhanced. As you get further from the wire, the strength gets weaker. If the amount of current flowing through it stays constant, its length and thickness have no bearing.

Therefore, the length of the wire in the magnetic field has an impact on the magnetic force's strength as well. The force acting on a wire increases with wire length in a magnetic field.

Learn more about experimental procedures from

https://brainly.com/question/17274244
#SPJ1

A inaccessible object is a dynamic variable on the free store without any pointer pointing to it.

Utilize the sextant's arc to determine the angle. By dividing the object's distance from the point of observation by the tan of the angle you calculated, you may use a scientific calculator to get the object's height.

The measuring of heights and distances that are unreachable is made easier by right-triangle trigonometry. By drawing a right triangle with the unknown height or distance as one of its sides and a known side and angle on the other, it is possible to determine the unknown height or distance.

To know more about inaccessible object visit:

https://brainly.com/question/21989844

#SPJ4

Answer:

dynamic variable

The final velocity of the two balls after collision is 1.7 m/s and the direction is 45⁰.

The given parameters;

   mass of the first clay ball, m₁ = 20 g = 0.02 kg

   initial velocity of the first clay ball, u₁ = 3 m/s

   mass of the second clay ball, m₂ = 30 g = 0.03 kg

   initial velocity of the second ball, u₂ = 2 m/s

The initial momentum of the fist ball is calculated as follows;

                               P₁ = m₁u₁

                                  P₁ = (0.02)(3)

                                 P₁ = 0.06 kg.m/s

The initial momentum of the second ball is calculated as follows

                                      P₂ = m₂u₂

                                        P₂ = (0.03)(2)

                                         P₂ = 0.06 kg.m/s

The resultant initial momentum of the two balls is calculated as follows;

Apply the principle of conservation of momentum, to determine the final velocity of the two balls;

The direction of the two ball's velocity is calculated as follows;

To know more about speed direction visit:

https://brainly.com/question/13776007

#SPJ1

The gravitational torque about the pivot when the mass is 60 ∘∘ above the +x-axis is (0.1838 Nm)k

Torque is the turning effect of a force which causes rotation. It is given by τ = F × d where

Since a 50 g mass rotates in a vertical plane--call it the xy-plane with the y-axis pointing up--at the end of a 75-cm-long, massless, rigid rod.

The gravitational torque is given by τ = F × d where

So, τ = F × d

= -(mgcosФ)j × di

= mgdcosФ(-j × i)

= -mgdcosФ(j × i)

= -mgdcosФ(-k)

= (mgdcosФ)k

Given that

Substituting the values of the variables into the equation, we have

τ = (mgdcosФ)k

= (0.05 kg × 9.8 m/s² × 0.75 m × cos60°)k

= (0.05 kg × 9.8 m/s² × 0.75 m × cos60°)k

= (0.3675 kgm²/s² × 0.5)k

= (0.18375 kgm²/s²)k

= (0.18375 Nm)k

≅ (0.1838 Nm)k

So, the torque is (0.1838 Nm)k

Learn more about torque here:

https://brainly.com/question/28219986

#SPJ1

The general instinct hypothesis, which contends that people are physiologically predisposed to or possess inclinations for violent behaviours, is known as the instinct theory of aggression in psychology.

In an effort to understand why we become aggressive and whether that behaviours can be altered, psychologists have developed three primary theories of aggression. Although many hypotheses have been put out, these three have proven most reliable and are crucial to comprehending the origins of violence. These hypotheses comprise as,

To know more about theory of aggression

https://brainly.com/question/3197702

#SPJ4

Field poles are electromagnets whose polarities change as the flow of current alternates in the field windings.

An electromagnet is a sort of magnet wherein the magnetic area is produced with the aid of an electric current. Electromagnets generally encompass cord wounds into a coil. A cutting edge through the wire creates a magnetic discipline that is focused inside the hole in the middle of the coil.

Electromagnets create a magnetic discipline through the application of power. When you introduce the modern, either from a battery or any other supply of strength, it flows through the wire. This creates a magnetic discipline around the coiled cord, magnetizing the metal as though it were a permanent magnet.

Learn more about Electromagnets here:-https://brainly.com/question/1408043

#SPJ4

The crane is under 5120 N of force. The crane touches the rock boulder and uses mechanical force to lift it.

Force is a physical phenomenon that can change an object's shape as well as its state of motion or rest. The SI unit of force is the Newton.

Jib, gantry, and overhead cranes are the three pieces of machinery used most frequently in the industry. Depending on the type of item to be moved, either a chain or wire rope hoist will be used. In the shipbuilding sector, material handling is the main use of overhead cranes during the assembly process.

Briefing:

Mass (m) = 400kg

Acceleration (a) = 3.00 m/s^2

Gravitational acceleration (g) = 9.81 m/s^2

Force (F) = mg + ma

Force (F) = m (g + a)

Force (F) = 400 (9.81+3)

Force (F) = 5120 N

To know more about force click:

brainly.com/question/28692142

#SPJ1

Answer:

Here, h1=4.00m,h92)=3.00m,Delta t =0.01 s.Letv1 be the velocity of the ball (actind downwards) just before striking the floor an dv20 be the velocity of the ball (acting upwaeds) ust after striking the floor. Then, change in velocity of the ball in time Δtv2−(−v1)v2+v1

:. acceleration, a=v2+v1Δt ..(i)

When body falls from height h1,

then u=o,v1,a=gandS=h1

As, v21=u2+2aS,

:. v_(1) ^(2) =0 + g h_(10 or v12–√gh1

Taking motion of the ball after striking the floor, then u=v2,v=0,a=−g,S=h2

As, v2=u22as,∴v21=0+2gh1orv_(1) =sqrt 32 g h_(1)Tak∈gmotionoftheballa>erstrik∈gthe⌊,⌋thenu=v_(2), v=0, a=- g, S=h_(2)As,v2=u2+2aS,wehave0 = v_(2)^(2) +2 (-g) h_92) otr v2=2–√gh2

Putting values in (i) we get,

a=2–√gh2+2–√gh1Δt)

a=2–√×9.8×3+2–√×9.8×40.01

= 1652m/s2.

Explanation:

Transmission coefficients are used in physics and electrical engineering when considering wave propagation in discontinuous media. The snells law is n₁sinθ1 = n₂sinθ2

The transmission coefficient describes the amplitude intensity or total power of the transmitted wave relative to the incident wave. The transmission coefficient is defined as the ratio of the transmitted particle flux to the incident particle flux and depends on the incident energy.

The sum of the reflected and transmitted energy must equal the total incident energy, so the transmission coefficient is calculated simply by subtracting the reflection coefficient. The ratio of the reflected wave amplitude to the incident wave amplitude is called the reflection coefficient.

Learn more about The transmission coefficients here:- https://brainly.com/question/9323897

#SPJ4

I think it is "energy cannot be destroyed but it can change forms".

If you are in a car with a helium balloon in the middle of the back seat and you turn left, the balloon moves towards right.

A change in the air's surrounding density causes a helium-filled balloon to move.

The balloon operates in opposition to what your body would normally do. Therefore, if the automobile stops, the balloon will move to the back. The secret is that you are composed of materials that are significantly heavier than air and that the balloon is loaded with helium (He).

Turn left, the balloon goes right. When you turn right, the balloon moves to the left; when you stop, it moves to the right.

It has to do with the motion of the air in your car. When you start moving forward while stationary, all of the air in the car rushes to the back, where it builds up an area of higher air pressure.

To know more about helium balloon:

https://brainly.com/question/14733676

#SPJ4

The distance travelled by the car after the brake was applied is 125 m.

The distance travelled by the car is calculated by applying the following kinematic equation as shown below.

Mathematically, the distance travelled by the car at the given average speed is calculated as;

s = [ ( v + u ) / 2 ] t

where;

The distance travelled by the car is calculated as;

s = [ ( 0 + 25 m/s ) / 2 ] ( 10 s )

s = 125 m

Learn more about distance travelled here: https://brainly.com/question/24283318

#SPJ1

An electromagnetic wave radiating from a specific 50.0-Hz AC power line has a maximum electric field strength of 13.0 kV/m. This extremely low frequency electromagnetic pulse has a wavelength of 6.00 x [tex]10^{6}[/tex]m.

A sinusoidal graph illustrates electromagnetic waves. It is made up of time-varying electric and magnetic fields that are perpendicular to each other and to the direction that waves travel.

Inverse proportionality describes the relationship between frequency and wavelength. Longer wavelengths are correlated with lower frequency, and vice versa. The fact that a wave's speed is equal to the product of its frequency and wavelength helps to explain how these two properties are related.

Briefing:

Given that,

Frequency of the power line, f = 50.0 Hz

Value of maximum electric field strength of 13.0 kV/m

The wavelength of this very low frequency electromagnetic wave is given by using relation as:

[tex]c = f[/tex]λ

λ [tex]= \frac{c}{f}[/tex]

λ [tex]= \frac{3.8 * 10^{8} m/s }{50}[/tex]

λ = 6 x [tex]10^{6}[/tex] m

To learn more about frequency visit:

brainly.com/question/14316711

#SPJ4

Joan is going with speed 30 m/s. Hence, option (C) is correct.

Acceleration is the rate at which a velocity changes over time. It qualifies as a vector quantity because it possesses both direction and magnitude. Meter/second^2 (m/s^2) is the SI unit of acceleration.

Given that: initial speed of the car: u = 10 m/s.

Uniform acceleration of the car: a =  4 m/s^2.

Distance travelled: s = 100 meters.

Let, the final speed is = v

Using the formula v² = u² + 2as, we get:

v = √(10² + 2×4×100) m/s.

= 30 m/s.

Hence, final speed of the car is 30 m/s.

Learn more about acceleration here:

brainly.com/question/12550364

#SPJ1

Between 400 nm and 700 nm of the electromagnetic spectrum, vegetation has the strongest response.

The electromagnetic spectrum travels in waves and spans an extensive spectrum from very long radio waves to very brief gamma rays. The human eye can simplest come across only a small portion of this spectrum called visible light.

In order from maximum to lowest power, the sections of the EM spectrum are named: gamma rays, X-rays, ultraviolet radiation, visible mild, infrared radiation, and radio waves.

In a tumbler, the purple mild travels the fastest, and the violet light travels the slowest of all seven hues. Velocity and wavelength are without delay proportional.

Learn more about Electromagnetic spectrum here:-https://brainly.com/question/23423065

#SPJ4

The angular momentum of a system does not depend on the point about which it is taken, according to equation (iv). the particles  eventually move back together because of mutual gravitational attraction.

As depicted in the following diagram, assume that two particles are present at positions P and Q at some point in time.

Think about a point R that is y miles away from a point Q, or QR=y PR=dy.

LP=mv0+mvd=mvd is the system's angular momentum around point P.

I The system's angular momentum around point Q is given by LQ=mvd+mv0=mvd.....(ii)

System's angular momentum about point R is given by LR=mv(d, y)+mv(y, d)=mvd....(iii)

The result of comparing equations I (ii), and (iii) is L P = LQ = LR....... (iv)

The angular momentum of a system does not depend on the point about which it is taken, according to equation (iv).

All objects with mass are attracted to one another by the gravitational attraction, which has a magnitude that is directly proportional to the masses of the two objects and inversely proportional to the square of their distance from one another.

Our feet remain firmly planted on the ground thanks to gravity, which also keeps the Moon in orbit around the Earth, the Earth in orbit around the Sun, the Sun in orbit around the galactic core of our Milky Way galaxy, and the Milky Way and Andromeda galaxies orbiting each other.

Learn more about galaxy here:

https://brainly.com/question/2905713

#SPJ4

Where the exercise here is to name the disorder, note that:

It should be mentioned that medication (such as antidepressants or benzodiazepines) and/or counseling may be used to treat a panic disorder such as cognitive-behavioral therapy.

A suitable course of treatment for dissociative disorders may involve counseling (such as cognitive-behavioral therapy, trauma-focused therapy, or psychodynamic therapy) and/or medication.

The focus of psychodynamic therapy is on unconscious processes as they show in the client's current behavior. Client self-awareness and knowledge of the effect of the past on present behavior are the aims of psychodynamic therapy.

Learn more about Dissociative disorder:
https://brainly.com/question/20430933
#SPJ1

The unit of G is found out to be m³/kg * s².

The force of gravitational attraction is represented by the equation.

F = (G m₁ m₂)/r²

where,

F is the magnitude of the gravitational attraction on either body

m₁ and m₂ are the masses of the bodies,

r is the distance between them

G is the gravitational constant

We need to find the unit of G,

G = (F * r²)/(m₁ m₂)

Let us place the units for the above formula,

G = (N * m²)/kg²

N = kg m/s²

G = (kg * m * m²)/ kg² * s²

G = m³/kg * s²

Thus, the correct option is m³/kg * s².

The question is incomplete. The complete question is 'Gravity causes objects to be attracted to one another. This attraction keeps our feet firmly planted on the ground and causes the moon to orbit the earth. The force of gravitational attraction is represented by the equation.

F= Gm1 m2 /r^2

where F is the magnitude of the gravitational attraction on either body, m1 and m2 are the masses of the bodies, r is the distance between them, and G is the gravitational constant. In Sl units, the units of force are kg m/s^2, the units of mass are kg, and the units of distance are m. For this equation to have consistent units, the units of G must be which of the following?

a. kg^3/ms^2

b. kgs^2/m^3

c. m^3/kgs^2

d. m/kgs^2

To know more about units:

https://brainly.com/question/20984485

#SPJ4

(a) The ratio of the slit separation d, to the slit width D;

                               d/D = 0.0001

(b The ratio of the slit width to the wavelength of the light source λ;

                                d/λ = 51.25

(c) The wavelength, in nanometers, of the light source;

                                   λ = 331.7 nm

(d) The slit width, in micrometers;

                                   d = 20.5 µm

(a) We know that Fringe width is given by,

                                  [tex]\beta =\frac{D\lambda}{d}[/tex]

Where,

           D = slit to screen distance

           λ = wavelength

           d = slit width

Given in the question,

           D = 2.05 m

           [tex]\beta =4 cm=0.04m[/tex]

Now,

          [tex]\frac{d}{D} =\frac{\lambda}{\beta } =\frac{400*10^{-9} }{0.04}[/tex]

                 d/D = 0.0001

Hence,

            The ratio of the slit separation d, to the slit width D;

                               d/D = 0.0001

(b) Ratio of d & λ,

                            [tex]\frac{d}{\lambda} =\frac{D}{\beta }[/tex]

                            [tex]\frac{d}{\lambda}=\frac{2.05}{0.04}[/tex]

                            [tex]\frac{d}{\lambda}=51.25[/tex]

Hence,

           The ratio of the slit width to the wavelength of the light source λ;

                                d/λ = 51.25

(c)  The wavelength of the light source,  

                            [tex]\lambda=\frac{D\beta }{d}[/tex]

                            [tex]\lambda=\frac{17*10^{-6} *0.04}{2.05}[/tex]

                            [tex]\lambda=331.7nm[/tex]

Hence,

            The wavelength, in nanometers, of the light source;

                             λ = 331.7 nm

(d) The slit width,

                           [tex]d =\frac{D\lambda}{\beta }[/tex]

                           [tex]d=\frac{400*10^{-9} *2.05}{0.04}[/tex]

                           [tex]d=20.5 \mu m[/tex]

Hence,

           The slit width, in micrometers;

                                   d = 20.5 µm

Learn more about Diffraction here

https://brainly.com/question/16749356                            

#SPJ4

The correct option is that C. The induced current will be clockwise until the bottom of the loop reaches the wire and will be counterclockwise when the bottom of the loop goes below this point. This is because the induced current is proportional to the rate of change of the magnetic field flux, which increases when the bottom of the loop is above the wire and decreases when the bottom of the loop is below the wire.

According to Faraday's law, the magnetic flux change rate in a circuit equals the magnitude of the induced EMF in the circuit. Additionally inversely correlated with the rate of change of magnetic flux in the circuit is hens induced current.

Lenz's law states that an induced current will flow in the opposite direction of the cause that is causing it. When the bottom of the loop is below this point, the induced current is counterclockwise until the bottom of the loop reaches the wire. This is because the magnetic field flux changes more quickly when the bottom of the loop is above the wire because the induced current is proportional to this

Learn more about current on:

https://brainly.com/question/24858512

#SPJ1

The path taken by a light beam after passing through a mirror's focus is where it hits the mirror and reflects back in exactly the same direction as it went in.

Specular reflection is the name for this. A smooth surface allows light to bounce back at the same angle that it was incident. Rays of light that are reflected off of a smooth surface go in that same direction.

The narrow beams of light that travel in straight lines along their courses as electromagnetic waves are known as rays. Though its path might be altered by reflection or refraction, light always moves in a straight line.

To know more about path of the light ray visit :-

https://brainly.com/question/3703500

#SPJ1

The final velocity of the weights will be 3.31 m/s

Weight = 5 lb

Coefficient of kinetic friction (µ) = 0.18

let T be tension

[tex]m_{1}[/tex]*g-T =[tex]m_{1}[/tex]*a

[tex]m_{1}[/tex] =10 lb = 4.53 kg

T-(µ)[tex]m_{2}[/tex]g =[tex]m_{2}[/tex]a

Adding both equations, we have

([tex]m_{1}[/tex]-k[tex]m_{2}[/tex])g =[tex]m_{2}[/tex] a

a = (4.53-0.2*2.26)*10/2.26 =18.04 [tex]m/s^{2}[/tex]

Using the equation of motion, we have,

[tex]v^{2} -u^{2} =2as[/tex]

Since the body starts from rest, the initial velocity, that is, u is zero.

So, u = 0 m/s

Putting this value in the above equation to calculate the final velocity, we have,

[tex]v^{2}[/tex] = 2as

v = [tex]\sqrt{(2*18.04*0.304) }[/tex]= 3.31 m/s

Thus, the final velocity of the weights will be 3.31 m/s

To read more about velocity, visit https://brainly.com/question/18084516

#SPJ4

A particle moves under the influence of a conservative force, The maximum x-coordinate of the particle at x = -3 m is 7 m.

Given that,

Potential energy of the particle u(x) = 5x² - 20x + 2

We know the relation between force and potential energy as,

F = -du/dx = -d/dx (5x² - 20x + 2) = -(10 x - 20 ) = 20 - 10 x at mean position x = 2.

At x = -3, amplitude is given by x = 2 - (-3) = 5

The maximum x co-ordinate is given as x = 5 + 2 = 7 m

To know more about potential energy function:

https://brainly.com/question/29998972

#SPJ4