Answer:
A) L = 0.388 μm
B) D = 3.78 mm
Explanation:
We are given;
Characteristics impedance; Z_o = 75 ohms
Nominal capacitance; C = 69pF/m = 69 × 10^(-12) F/m
dielectric constant; k = 2.23
Inner diameter of conductor; d = 0.584 mm
A) Now formula for Characteristics impedance is given as;
Z_o = √(L/C)
Where L is the inductance per metre.
Making L the subject, we have;
L = (Z_o)²C
L = 75² × 69 × 10^(-12)
L = 0.388 × 10^(-6) m
L = 0.388 μm
B) To get the outer diameter, we will use the formula;
Z_o = (138/√k) log(D/d)
Where;
D is outer diameter.
Thus, Plugging in the relevant values;
75 = (138/√2.23) × log (D/0.584)
log (D/0.584) = 0.81158611538
(D/0.584) = 10^(0.81158611538)
D/0.584 = 6.48016576435
D = 6.48016576435 × 0.584
D = 3.78 mm
You are given a pot of hot tea (350 mL) at a temperature of 85°C and a quantity of ice at -12°C. Determine the absolute minimum amount of ice you can add to the hot tea so that at equilibrium you have iced tea (ie. a very, very small amount of ice and some water). You can assume tea has the same density (1.00 g/mL) and specific heat (4190 J/kgK) as liquid water. The heat of fusion of H2O is 3.33x10^5 J/kg. The specific heat of ice is 2090 J/kgK.
Answer:
348 g
Explanation:
The heat gained by the ice equals the heat lost by the hot tea.
Also, since we require a very, very small amount of ice and some water, to still have some ice, the temperature of the hot tea has to decrease to the melting point of ice which is 0°C. So, the final temperature of the mixture is 0 °C.
So, mc(T - T') + mL = -MC(T - T") where m = mass of ice, c = specific heat of ice = 2090 J/kgK., T = final temperature of mixture = 0 °C, T' = initial temperature of ice = -12 °C, L = heat of fusion of H2O = 3.33 × 10⁵ J/kg, M = mass of hot tea = ρV where ρ = density of tea = 1.00 g/mL and V = volume of hot tea = 350 mL. So, M = ρV = 1.00 g/mL × 350 mL = 350 g = 0.350 kg, C = specific heat of tea = 4190 J/kgK and T" = initial temperature of tea = 85 °C.
Making m subject of the formula, we have
mc(T - T') + mL = -MC(T - T")
m[c(T - T') + L] = -MC(T - T")
m = -MC(T - T")/[c(T - T') + L]
substituting the values of the variables into the equation, we have
m = -MC(T - T")/[c(T - T') + L]
m = -0.350 kg × 4190 J/kgK(0 °C - 85 °C.)/[2090 J/kgK(0 °C. - (-12 °C)) + 3.33 × 10⁵ J/kg]
m = -1466.5 J/kK(- 85 °C)/[2090 J/kgK(0 °C + 12 °C)) + 3.33 × 10⁵ J/kg]
m = 124652.5 J/[2090 J/kgK(12 °C) + 3.33 × 10⁵ J/kg]
m = 124652.5 J/[25080 J/kg + 3.33 × 10⁵ J/kg]
m = 124652.5 J/358080 J/kg
m = 0.3481 kg
m = 348.1 g
m ≅ 348 g
So, the minimum amount of ice to be added is 348 g.
Work to be performed can come from the work package level of the work breakdown structure as well as other sources. Which of these is NOT a source of authorized work to be performed?
a. Scope creep
b. Defect repairs
c. Preventive actions
d. Corrective actions
A project is meant to achieve clearly defined goals within present constraints
The correct option for the source of work in a project which is NOT a source of authorized work to be performed is option (a)
a. Scope creep
The reason for the selecting the above option is as follows;
In project management, alongside work planned in a work package, authorized work to be performed can come from;
The repairing of defects found in completed work and which is a requirement for the project to be approvePreventive actions, that are meant to mitigate factors that affect the project timeline and costCorrective actions which include actions meant to rectify parts of the project that produce an error outcomeA scope creep, however, is generally is due to the inclusion of the end
users of the project at a time that is behind schedule, insufficient analysis of
the requirements, and project complexity underestimation. and consists of
changes made after a project has commenced
A scope creep therefore, changes the amount of work to be done which
therefore alters the project timeline, and due to project, budgetary, and
end user constraints, CANNOT be a source of authorized work to be
performed
The correct option for the source that is NOT a authorized work to be performed is option a. Scope creep
Learn more about scope creep here:
https://brainly.com/question/14061926
an atom that gained an electron is called
Answer:
Hey mate......
Explanation:
This is ur answer.....
When an atom gains/loses an electron, the atom becomes charged, and is called an ion.Hope it helps!
Brainliest pls!
Follow me :)
. Bơm kiểu piston tác dụng đơn có áp suất p=0,64 Mpa và lưu lượng Q=3,5 l/s. Xác định tốc độ quay của trục bơm và công suất của bơm nếu biết đường kính piston D=150 mm; bán kính tay quay R=60 mm; hiệu suất thể tích của bơm là 0=0,94; hiệu suất chung của bơm b=0,80.
Answer:
not understand language
True or false: You can create a network with two computers.
Answer
True
Which of the following conditions were present in over 80% of paddling fatalities from 1995-2000?
Answer:
80% of the people that were killed weren't wearing a safety flotation device ( in correct terminology Personal Flotation Device, or PFD )
Explanation:
Hence they drowned due to the lack of safety.
The condition present in over 80% of paddling fatalities is that the victims were said to be not wearing a personal flotation device (PFD).
What is paddling in the sea?The act of paddling is known to be a sport or something one can do for fun or for games.
Conclusively, a lot of paddling fatalities 1995-2000 was due to the fact that the people who were engage in the sport or act were not putting on a personal flotation device (PFD) and this can lead to death or drowning.
Learn more about paddling fatalities from
https://brainly.com/question/3787626
Rafel knows that lessons learned is a valuable aid to future projects. When should he and his team address
lessons learned on a project?
Select an answer:
Add lessons learned as a topic in status meetings
Review past lessons learned so a new one does not have to be created,
Create lessons learned at the end of the project.
Brainstorm lessons learned at the beginning of a project
Answer: Create lessons learned at the end of the project.
Explanation:
Lessons learned are the experiences that are gotten from a project which should be taken into account for the future projects. Lesson learned are created at the end of the project.
The main objective of the lessons learned is that they show both the positive experience and the negative experience of a project and this will help the future projects that will be undertaken.
Magnetic particle testing can be done only on metals that can be magnetized.
True or false
hỗ trợ mình với được không các bạn
Answer:
Explanation:
Be bop
what does mean setbacks with MRT station?
A O.1m³ rigid tank contains steam initially as 500k pa and 200°C. The steam is now allowed to cool until the temperature drops to 50°C. Determine the amount of heat transfer during the process and the final pressure in the tank
Answer:
Check it out here
Explanation:
A resistor has code 104 printed on it .What is the resistive value of this resistor
Answer:
X = 1 (1st digit in the code)
Y = 0 (2nd digit)
Z = 4 (3rd multiplier digit)
104 → 10 × 10^4 Ω
→ 10 × 10000Ω
→ 100 kΩ
resistors are marked 104, 105, 205, 751, and 754. The resistor marked with 104 should be 100kΩ (10x10^4), 105 would be 1MΩ (10x10^5), and 205 is 2MΩ (20x10^5). 751 is 750Ω (75x10^1), and 754 is 750kΩ (75x10^4).
Here we need to understand how a code in a resistor gives us information on the resistor. Here we will see that the code means that the resistance is 100,000 Ω.
When we use numbers, let's assume that we have 3 single-digit numbers abc.
So if the code in our resistor is abc, this will mean that the resistance of the resistor is:
ab×10^c Ω
Using this general rule we can see that if the code is 104, then the resistance will be:
r = 10×10^4 Ω
= 100,000 Ω
Then we can conclude that the resistive value of this resistor is 100,000 Ω
If you want to learn more, you can read:
https://brainly.com/question/74415
The impeller shaft of a fluid agitator transmits 20 kW at 430 rpm. If the allowable shear stress in the impeller shaft must be limited to 65 MPa, determine (a) the minimum diameter required for a solid impeller shaft. (b) the maximum inside diameter permitted for a hollow impeller shaft if the outside diameter is 36 mm. (c) the percent savings in weight realized if the hollow shaft is used instead of the solid shaft. (Hint: The weight of a shaft is proportional to its cross-sectional area.)
Given :
Power, P = 20 kW
Speed, N = 430 rpm
Allowable shear stress, τ = 65 MPa
Torque in the shaft is given by :
[tex]$P=\frac{2 \pi NT}{60}$[/tex]
[tex]$T=\frac{60 \times 20 \times 10^3}{2 \pi \times 430}$[/tex]
T = 444.37 N.m
Diameter of the solid shaft is
[tex]$d=\sqrt[3]{\frac{16 T}{\pi \tau}}[/tex]
[tex]$d=\sqrt[3]{\frac{16 \times 444.37}{3.14 \times 65}}[/tex]
[tex]$d=\sqrt[3]{34.83} $[/tex]
d = 3.265 m
d = 326.5 mm
Internal diameter of the hollow shaft is :
[tex]$\frac{T}{\frac{\pi}{32} \left( d_0^4 - d_i^4 \right)}=\frac{\tau}{d_0/2}$[/tex]
[tex]$\frac{444.37}{\frac{3.14}{32} \left( 0.036^4 - d_i^4 \right)}=\frac{65 \times 10^6}{0.036/2}$[/tex]
[tex]$\frac{444.37}{0.09 \left( 1.6 \times 10^{-6} - d_i^4 \right)}=\frac{65 \times 10^6}{0.018}$[/tex]
[tex]$\frac{7.99}{ \left( 1.6 \times 10^{-6} - d_i^4 \right)}=5850000$[/tex]
[tex]$1.3\times 10^{-6} = 1.6 \times 10^{-6} - d_i^4 \right)}$[/tex]
[tex]$d_i^4=300000$[/tex]
[tex]$d_i = 23.40$[/tex] mm
Percentage savings in the weight is given by :
Percentage saving = [tex]$\frac{W_{solid}-W_{hollow}}{W_{solid}}\times100$[/tex]
[tex]$=\frac{V_{solid}-V_{hollow}}{V_{solid}}\times100$[/tex]
[tex]$=\frac{d^2 - (d_0^2 - d_i^2)}{d^2} \times 100$[/tex]
[tex]$=\frac{(326.5)^2 - (0.036^2 - (32.40)^2)}{(326.5)^2} \times 100$[/tex]
[tex]$=\frac{106602 - \left(1.29 \times 10^{-3} - 1049.76 \right)}{106602} \times 100$[/tex]
[tex]$=\frac{106602 - 1049 }{106602} \times 100$[/tex]
[tex]$=\frac{105553 }{106602} \times 100$[/tex]
= 99.01 %
A 2-stage dcv that has an internal pilot does not work well (if at all) on
Answer:
i really font onow why tbh eot you
A steel component with ultimate tensile strength of 800 MPa and plane strain fracture toughness of 20 MPam is known to contain a tunnel (internal) crack of length 1.4 mm. This alloy is being considered for use in a cyclic loading application for which the design stresses vary from 0 to 410 MPa. Would you recommend this alloy for this application
Complete question:
A steel component with a tensile strength of 800 MPa and fracture toughness Kic=20 MPa Nm is known to contain internal cracks (also called tunnel cracks) with the maximum length of 1.4 mm. This steel is being considered for use in a cyclic loading application for which the designed stresses vary from 0 to 420 MPa. Would you recommend using this steel in this application?
a. Not sure. Because cyclic loading is applied. Fatigue test is needed in order to make the recommendation.
b. Yes, this because the tensile strength of steel is much higher than the applied highest stress of 420 MPa.
c. Yes, this because the calculated critical stress to fracture for the cracks is higher than the highest applied stress of 420 MPa and the steel can withstand the stress of 420 MPa.
d. No. Although the calculated critical stress to fracture for the cracks is slightly higher than the highest applied stress of 420 MPa and the steel may withstand the static stress of 420 MPa, the cyclic loading may cause rapid fatigue fracture.
Answer:
A. Not sure. Because cyclic loading is applied. Fatigue test is needed in order to make the recommendation.
Explanation:
we are not sure if to recommend this alloy for this application given that this material has already been left to experience fatigue degradation. the cyclic load application brings about a growth in the crack. We know that cyclic loading is continuous loading that is useful for the testing of fatigue. Therefore the answer to this question is option a. We cannot make recommendations except fatigue testing has been carried out.
thank you!
what is tracer lathe machine
Answer: The tracer lathe is a roughing operation for the output shaft on rear wheel drive transmissions.
Explanation:
The secondary coil of a step-up transformer provides the voltage that operates an electrostatic air filter. The turns ratio of the transformer is 41:1. The primary coil is plugged into a standard 120-V outlet. The current in the secondary coil is 1.2 x 10-3 A. Find the power consumed by the air filter.
Answer:
5.9 watts
Explanation:
The secondary voltage is the primary voltage multiplied by the turns ratio:
(120 V)(41) = 4920 V
The power is the product of voltage and current:
(4920 V)(1.2·10^-3 A) = (4.92)(1.2) W = 5.904 W
The power consumed is about 5.9 watts.
A recessed luminaire bears no marking indicating that it is ""Identified for Through- Wiring."" Is it permitted to run branch-circuit conductors other than the conductors that supply the luminaire through the integral junction box on the luminaire?
Answer:
No it is not permitted
Explanation:
It is not permitted because as per NEC 410.21 policy no other conductor is allowed to be passed through integral junction box luminaries unless such conductor supply recessed luminaries.
The marking will show that the Luminaries is of the right construction or right installation to ensure that the the conductors ( in the outer boxes ) will not be exposed to temperatures greater than the conductor rating, hence the lack of marking makes it not to be permitted.
1) (30 pts ) Oxygen (O2) flows through a pipe, entering at at 4 m/sec at 10000 kPa, 227oC. For a pipe inside diameter of 3.0 cm, find the volumetric flow rate (m3/sec) and the mass flow rate of the gas (kg/sec) assuming you have an ideal gas
Complete Question
Nitrogen (N2) flows through a pipe, entering at at 4 m/sec at 1000 kPa, 2270C. For a pipe inside diameter of 3 cm, find the volumetric flow rate (m3/sec) and the mass flow rate of the gas (kg/sec) assuming you have an ideal gas Then using your ideal gas mass flow rate find the rate at which enthalpy enters the pipe (kJ/sec) NO Cp, Cv, k permitted
Answer:
[tex]H=9.91kJ/sec[/tex]
Explanation:
From the question we are told that:
Velocity [tex]v=4 m/sec[/tex]
Pressure [tex]P=1000kPa[/tex]
Temperature [tex]T=227 \textdegree C[/tex]
Diameter [tex]d=3cm=>0.03m[/tex]
Generally the equation for volumetric Flow Rate is mathematically given by
[tex]V_r=(\frac{\pi*d^2}{4}v)[/tex]
[tex]V_r=(\frac{\pi*(0.03)^2}{4} *4)[/tex]
[tex]V_r=0.002827m^3/s[/tex]
Generally the equation for mass Flow Rate is mathematically given by
[tex]m_r=\frac{PV_r}{RT}[/tex]
[tex]m_r=\frac{1000*0.002827}{0.297*(227+273)}[/tex]
[tex]m_r=0.019kg/sec[/tex]
Generally the equation for mass Flow Rate is mathematically given by
Using gas Table for enthalpy Value
[tex]T=500K=>h=520.75kg[/tex]
Therefore
[tex]H=mh[/tex]
[tex]H=0.019*520.75[/tex]
[tex]H=9.91kJ/sec[/tex]
what the different methods to turn on thyrister and how can a thyrister turned off
Answer:
forward voltage triggering
temperature triggering
dv/dt triggering
light triggering
gate triggering
Then turning off;
Turn off is accomplished by a "negative voltage" pulse between the gate and cathode terminals
Explanation:
hope it helps
Question in Statistics and Probability 2
Petrol samples were taken at three different stations along a national highway to determine whether the octane rating varied from one station to another. Six petrol specimens of the same category were randomly selected at each station in different days. We are interested to know if there is sufficient evidence to indicate a difference in the mean octane rating at the different stations.
State the Null and the Alternative Hypotheses.
I want to explain what 2000 feet looks like to young children so that they can imagine it in class
Answer:
maybe take a really common toy kids play with or often see, find the average height for the toy and do the math to see how many of those toys stacked ontop of eachother would make up 2000 feet. For example (this isn't accurate btw just an idea of what it would sound like but) "Have you ever seen a barbie doll? well if you stack 400 barbie dolls ontop of their head it would be equal to 2000 feet."
Explanation:
sometimes taking common or beloved objects children have into your examples makes them have a better image of how small or how big something is.
Which statement describes the relay between minerals and rocks ?
Answer:
•○●□■hey hi!■□●○•Explanation:
Minerals and rocks are the same. Aggregates of minerals form rocks. Minerals determine the texture of a rock. Most rocks are made of a single mineral type.
☆♡hope this helps♡☆once scientist has asked a question conducted an investigation and analyzed the data his or hwr goalis to
Answer:
hola
Explanation:
Explanation:
so its an question?..........
Question 1 of 8.
What should you do to drive safely in the station?
Turn on your hazard lights
Roll your windows down and turn off the radio
Maintain idle speed (below 5mph)
All of the above
Mark for follow up
Answer: all of the above
Explanation:
To drive safely in the station, the correct option is D. All of the above.
It should be noted that when a person is driving, it's essential for the person to drive carefully in a station.
One should not smoke in a station. Also, it's important that the driver should turn on their hazard lights
Furthermore, it's important for one to roll their windows down, turn off the radio and also maintain idle speed.
In conclusion, the correct option is D.
Read related link on:
https://brainly.com/question/18889428
8.50 nC of charge is uniformly distributed along a thin rod of length L = 9.20 cm, which is then bent into a semicircle. What is the magnitude of the electric field at the center of the circle
Flat plate collector can provide temperature upto_____
Answer:
80⁰C
Explanation:
80°C.
Normal flat plate collectors can deliver heat at temperatures up to 80°C. Deficiency rates for normal flat plate collectors can be classified as visual losses, which produce with cumulative angles of the incident sunshine, and thermal losses, which upsurge fast with the working temperature intensities
Tech A says that the voltage regulator controls the strength of the rotor s magnetic field. Tech B says that the voltage regulator is installed between the output terminal of the alternator and the positive terminal of the battery. Who is correct?
Answer:
Voltage Regulator
Technician A is correct.
Explanation:
Technician B is not correct. The voltage regulator is not installed between the output terminal of the alternator and the positive terminal of the battery as claimed by Technician B. Technician A's opinion that the voltage regulator controls the strength of the rotor's magnetic field is correct. The computer can also be used to control the output of the alternator by controlling the field current.
The load on a bolt consists of an axial pull of 10 KN together with a transverse shear force of 5 KN. Find the diameter of bolt required according to I. Maximum principal stress theory; 2. Maximum shear stress theory; 3. Maximum principal strain theory, 4. Maximum strain energy theory, and 5 Maximum distortion energy theory. Take permissible tensile stress at elastic limit = 100 MPa and poisson's ratio = 0.3
Answer:
hey. its a big question. solved from *c hegg
Explanation:
To avoid a possible collision with a manned airplane, you climb your unmanned aircraft to yield the right of way. In doing so, your unmanned aircraft reached an altitude greater than 600 feet AGL. To whom must you report the deviation?
Answer:
you have to report to the federal aviation administration upon request
Explanation:
An unmanned aircraft can also be a drone it is an aircraft that does not have passengers or a human pilot.
Such an aircraft could be fully autonomous but most times they have a human pilot who controls it remotely.
Now you have to report this deviation to the federal aviation administration. This body is responsible for the enforcement of regulations that have to do with the manufacture, operation and maintenance of aircrafts. The body makes sure there is an efficient and safe system for a navigation and they also control air traffic.
