Answer:
Density = 4.84 g/cm³
Explanation:
Given the following data;
Mass = 30 g
Volume = 6.2 cm³
To find the density of the piece of iron;
Density can be defined as mass all over the volume of an object.
Simply stated, density is mass per unit volume of an object.
Mathematically, density is given by the equation;
[tex]Density = \frac{mass}{volume}[/tex]
Substituting into the equation, we have;
[tex]Density = \frac{30}{6.2}[/tex]
Density = 4.84 g/cm³
as light passes from water into air it has a refracted angle of 35 degrees. calculate the incident angle of the light.
A steel railroad track has a length of 79 when the temperature is 2◦C. What is the increase in the length of the rail on a hot day when the temperature is 35◦C? The linear expansion coefficient of steel is 11 × 10−6 (◦C)−1.
Answer:
We know that the length is 79 (there are no units of length in the question, so i will leave it as it is written, without units) when the temperature is 2°C.
We want to find the increase in length when the temperature is 35°C, knowing that the linear expansion coefficient is 11*10^(-6) °C^-1
The change in length is just given by the equation:
[tex]\Delta L = \alpha*L_0* (T_1 - T_0)[/tex]
where:
α = 11*10^(-6) °C^-1
T₀ is the initial temperature, so T₀ = 2°C
T₁ is the final temperature, so T₁ = 35°C
L₀ is the initial length, so L₀ = 79
Replacing these in the equation we get:
ΔL = ( 11*10^(-6) °C^-1)*79*(35°C - 2°C)
= 0.28677
So the length of the railroad will increase by 0.28677
Describe how a wind turbine generates energy.
The diameter of a copper wire is thought to be approximately 0.3mm. Which instrument should be used to obtain a more accurate measurement of the diameter of the wire? A measuring tape B metre rule C micrometer D ruler 2
Answer:
C
Explanation:
The correct answer should be the micrometer.
The micrometer is an instrument that is capable of measuring the component of an object to very high precision. It is used to obtain accurate measurements in engineering.
In the case of the copper wire, the diameter of 0.3 mm was an approximation and a more accurate measure of the diameter would be obtained by using the micrometer.
The correct option is C.
Do solar panels create enough energy to power the car throughout the day?
Answer:
Yes, but only if it's sunny.
Explanation:
As you know, solar panels generate energy through the sun's rays of light (better known as sunlight). Therefore, as long as the sun is shining high in the sky, the car will generate electricity and be able to function. If this vehicle was only powered by solar panels, it would not function during the night, in cloudy areas, and/or in dark places (such as parking garages or home garages).
Hope this helps!
CAN SOMEONE PLS HELP ME ILL GIVE YOU BRAINLIEST!!!!
A 7000 N braking force is used to slow a car down. The car was traveling at 25 m/s before the
brakes were applied and was traveling at 5 m/s after 6 seconds. What is the mass of the car? (ANS:
2100 kg)
Answer:
the answer is already there lol
Explanation:
Answer:
answer is there you can see from there lol
Explanation:
how do icebergs form
Answer:
They break off large ice sheets found at the North and South poles.
Answer:
The answer is D
Explanation:
They break off large ice sheets found at the poles.
Which force determines if an object is going to move or stay at rest?
a. Friction Force
b. Normal Force
c. Applied Force
d. Net Force
Answer:
a
Explanation:
because it's need someone moving it so it can move somewhere else
The wind blows a leaf at 37.9 m/s for 118 s left. How are does the leaf go in that period of time.
A) 3.11 m, left
B) 4470 m, left
C) 80.1 m, left
D) 0.321 m, left
Explanation:
distance = velocity * time
d = 37.9 * 118
distance = 4472.2
2. A student drew the diagram below to model the movement of an object orbiting the Sun. Which object was she most likely modeling? a meteor a planet a comet an astroid
Answer:
A comet
Explanation:
The picture is of an elliptical orbit of a comet. You can tell it is a comet because of the tail. Also, I just took the test and it was a comet.
the gravity on mars is 3.8 m/s2 and you weigh 200 N. your mass will be??
Answer:
Mass = 52.63 kilograms
Explanation:
Given the following data;
Acceleration due to gravity = 3.8 m/s²
Weight = 200 N
To find mass;
Mathematically, the weight of a physical object is given by the formula;
Weight = mass * acceleration due to gravity
Substituting into the formula, we have;
200 = mass * 3.8
Mass = 200/3.8
Mass = 52.63 kg
Croquet balls must have a mass of 0.50 kg. A red croquet ball is moving at 5 m/s. It strikes an at-rest green croquet ball head-on and then continues to move in the same direction, but with a speed of 2 m/s. What is the final speed of the green ball?
A.
5 m/s
B.
0.5 m/s
C.
2 m/s
D.
3 m/s
Answer:
Explanation:
The Law of Momentum Conservation for us has the equation
[tex][m_rv_r+m_gv_g]_b=[m_rv_r+m_gv_g]_a[/tex] and filling in:
[tex][(.50)(5.0)+(.50)(0)]=[(.50)(2.0)+(.50)v_g][/tex] and
2.5 = 1.0 + .50v and
1.5 = .50v so
v = 3 m/s
The final speed of the green ball is 3m/s. This can be calculated by the law of conservation of momentum. Thus, the correct option is D.
What is the law of Conservation of Momentum?
The principle of the law of conservation of momentum states that if any two objects undergo collision, then the total momentum of the objects before and after the collision will be the same if there is no external force acting on the colliding objects.
The Law of Conservation of Momentum has the equation which is:
m₁ × u₁ + m₂ × u₂ = m₁ × v₁ + m₂ × v₂
where, m₁ = mass of object 1,
u₁ = initial velocity of object 1 before collision,
m₂ = mass of object 2,
v₁ = final velocity of object 1 after collision,
v₂ = final velocity of the object 2 after collision.
0.50 × 5 + 0.50 × 0 = 0.50 × 2 + 0.50 × v₂
2.5 + 0 = 1.0 + 0.50 × v₂
2.5 - 1.0 = 0.50 × v₂
1.5 = 0.50 × v₂
1.5/ 0.5 = v₂
v₂ = 3m/s
Therefore, the correct option is D.
Learn more about Momentum here:
https://brainly.com/question/24030570
#SPJ2
A man who weighs 75kg on the surface of the earth whose mass is 6*10^24kg. If the radius of earth is 6480km ,calculate the force of attraction between them.
Answer:
718.02N is the answer to the question
Do only number 3 and thank
Charge = 0.2 Ah is the correct answer...
Cuatro contenedores idénticos tienen la misma cantidad de gas helio a la misma temperatura inicial. Los recipientes también cuentan con un émbolo móvil que no permite que el helio escape. Cada muestra de gas sigue un proceso distinto como se describe a continuación: Muestra 1: 500 J de calor salen del gas y este realiza 300 J de trabajo. Muestra 2: 500 J de calor entran al gas y este realiza 300 J de trabajo. Muestra 3: 500 J de calor salen del gas y se hace un trabajo de 300 J sobre él. Muestra 4: 500 J de calor entran al gas y se hace un trabajo de 300 J sobre él.
Answer:
1) ΔE = -800 J, 2) ΔE = 200 J, 3) ΔE = -200 J, 4) ΔE = 800 J
Explanation:
For this exercise let's use the first law of thermodynamics
ΔE = Q + W
Where we will apply this expression to several cases
1) output Q = 500 J and does work of W = 300 J.
The two processes involve an energy output
ΔE = - 500 - 300
ΔE = -800 J
Therefore, the internal energy of the gas decreases by this amount,
2) enter Q = 500J and do work of W = 300 J
Positive heat is added and does negative work
ΔE = 500 - 300
ΔE = 200 J
3) they leave Q = 500 J and do (work on the gas) W = 300J
negative heat and positive work come out
ΔE = -500 + 300
ΔE = -200 J
4) heat enters Q = 500 J, work on gas W = 300 J
both positive
ΔE = 500 + 300
ΔE = 800 J
A first aid provider is trained to do the following except:
A) diagnose the victims condition
B) recognize, asses and prioritize the need for first aid
C) seek professional medical assistance when necessary
D) provide appropriate first aid care
Some people can roll the tongue into a tube shape, while others cannot. Practicing is not likely to help because tongue-rolling is an inherited trait. The allele for rolling the tongue (R) is dominant to the allele for not being able to roll the tongue (r). Look at the Punnett square. It shows a cross between two parents with at least one R allele. Drag each option to its spot to correctly finish the Punnett square.
Hope this helps you.
Which best describes the energy of a sound wave as it travels through a medium? It increases. It decreases. It remains the same. It depends on the medium.
Answer:
It depends on the medium
Explanation:
2021 edge
The energy of a sound wave decreases as it travels through a medium to another medium. Thus, the correct option is D.
What is a Sound wave?A sound wave is the pattern of disturbance which is caused by the energy which is travelling away from the source of the sound in that medium. Sound waves are the longitudinal waves. This means that the propagation of these vibration of particles is parallel to the energy which this wave propagation direction has. When the atoms in the medium are set in vibration then they move back and forth in a direction. This continuous to occur in back and forth motion resulting in a high-pressure and a low-pressure region in the medium and thus propagating sound.
Sound wave is the physical vibration wave which travel through the air to reach the ears of organisms. Sound energy is the result when force makes an object to vibrate. A wave can lose energy as it travels through a medium because the medium can also absorb the energy from the wave. The medium changes some of the acoustic energy of the sound wave into heat energy.
Therefore, the correct option is D.
Learn more about Sound wave here:
https://brainly.com/question/21995826
#SPJ2
What is a sound wave?
A certain AM radio wave has a frequency of 24Hz. Given that radio waves travel at 3 m/s, what is the wavelength of this radio wave?
Answer:
Wavelength of AM radio wave = 0.125 meter
Explanation:
Given:
Frequency of AM radio wave = 24 Hz
Velocity of AM radio wave = 3 m/s
Find:
Wavelength of AM radio wave
Computation:
Wavelength = Velocity / Frequency
Wavelength of AM radio wave = Velocity of AM radio wave / Frequency of AM radio wave
Wavelength of AM radio wave = 3 / 24
Wavelength of AM radio wave = 0.125 meter
If the distance between the source of sound and observer is reduced to one half, then
the intensity of sound will become
Answer:
Let the power delivered by the sound wave be 'P'
Intensity by definition is the power delivered per unit area.
i.e. I =
dA
dP
;
In spherical polar coordinate system dA = r
2
Ω
I =
r
2
Ω
dP
;
I ∝
r
2
1
So if distance increases 3 fold. The Intensity becomes
9
1
times the initial
Dad, if you are seeing this, then I have run away. Angie has been torturing me ever since you started dating her, and I have had enough of it. I have been trying to tell you, but you would never listen. Goodbye, and Angie, if you are seeing this, I posted this on here, so you will not be able to delete anything. Have a nice life
Answer:
hey are you ok!?!?!?!
Explanation:
Is Angie your Dad new gf or wife???
Answer:
:(
Explanation:
u ok?
running away from problems only makes things worse. Your teaching urself to run. but I dont blame u
anyway hope u find what ur looking for out there!!
Find the resultant of these two forces : 2.00 x 10^2 N due east and 4.00 x 10^2 N 30.0 degree north of west
If two vectors are represented both in magnitude and direction by the two adjacent sides of a triangle taken in an order, then their resultant is given by the third side taken in the reverse order.
Resultant vector :
R = sqrt of A^2 + B^2 + 2ABcosθ
given :
A = 200 units
B = 300 units
θ = 30 degrees
∴ R = sqrt of 200^2 + 300^2 + 2(200)(300)cos35
the answer is 477.805656
Can someone help me :)
Answer:
undergone a chemical change
Explanation:
Answer:
undergone a chemical change
Mrs. Botts applies brakes on a car help it to decelerate at the rate of -0.80m/s2. What distance is required to stop the car when it is moving 17 m/s.
Answer:
Explanation:
vf=0
vi = 17
a = -0.8
Δx = ?
vf^2 = vi^2 + 2 a Δx
Δx = (vf^2 - vi^2) / 2a
Δx = (0-17^2) / 2 (-0.8)
Δx = 180.625 m
when two capacitors are connected in series, the effective capacitance is 2.4muF and when connected in parallel, the effective capacitance is 10muF. calculate the individual capacitances.
Answer:
let one capacitor be x and other be y
[tex]in \: parallel \: connection : \\ \frac{x + y}{xy} = 10 \times {10}^{ - 6} - - - (a) \\ in \: series \: connection : \\ x + y = 2.4 \times {10}^{ - 6} - - - (b) \\ in \: (a) : \\ \frac{2.4 \times {10}^{ - 6} }{xy} = 10 \times {10}^{ - 6} \\ xy = 0.24 - - - (c) \\ from \: (b) : \\ y = (2.4 \times {10}^{ - 6} ) - x \\ \therefore \: in \: (c) : \\ x(2.4 \times {10}^{ - 6} - x) = 0.24 \\ 2.4 \times {10}^{ - 6} x - {x}^{2} = 0.24 \\ {x}^{2} - 2.4 \times {10}^{ - 6} x - 0.24 = 0 \\ x = 0.5 \\ 0.5y = 0.24 \\ y = 0.48 \\ { \boxed{ C _{1} = 0.5 \: farads}} \\ { \boxed{C _{2} = 0.48 \: farads}}[/tex]
When do we say that work is done?
Answer:
Work is said to be done when a force applied to an object moves that object. We can calculate work by multiplying the force by the movement of the object.
Answer:
Work is done by a force on an object if (i) a force acts on the object and (ii) the object is displaced from its original position
Which statement describes the possible interaction(s) between two objects
caused by the electric, magnetic, or gravitational force between them?
O A. Electric and gravitational forces only cause objects to repel each
other, and magnetic forces only cause objects to be attracted to
each other.
O B. All three types of forces only cause the objects to repel each other.
O C. Gravitational forces only cause objects to be attracted to each
other, and magnetic and electric forces can cause objects to
attract or repel each other.
O D. All three types of forces only cause the objects to be attrachyd to
each other.
The statement which describes the possible interaction(s) between two objects caused by the electric, magnetic, or gravitational force between them is:
Gravitational forces only cause objects to be attracted to each other, and magnetic and electric forces can cause objects to
What is force?Force can be defined as the push or pull on an object with mass that causes it to change its velocity
So therefore, the statement which describes the possible interaction(s) between two objects caused by the electric, magnetic, or gravitational force between them is:
Gravitational forces only cause objects to be attracted to each
other, and magnetic and electric forces can cause objects to
Learn more force:
https://brainly.com/question/14839816
#SPJ1
HELP ME ILL MARK U THE BRAINLIEST
the crane takes 2.5s to raise the box 3.0 m. Calculate the power output of the crane
Answer:
Power = 1800 W
Explanation:
Power = work / time
Power = 4500 / 2.5
Power = 1800 W
Que capacidade física consiste em deslocar o corpo no espaço o mais rápido possível, mudando o centro de gravidade de posição, sem perder o equilíbrio e a coordenação dos movimentos?
Answer:ur mom
Explanation:because
