explain why sound wave travel faster in liquid than gas​

Answer:

If efficiency is .22 then  W = .22 * Q   where Q is the heat input

Heat Input    Q = 2510 / .22 = 11,400 J

Heat rejected = 11.400 - 2510 = 8900  J of heat wasted

Also, 8900 J / (4.19 J / cal) = 2120 cal

An efficiency is the measure of productivity of an engine. The heat rejected by the engine is 8900 Joules.

An efficiency of a heat engine is the ratio of the work done and heat supplied.

Given is the automobile engine has the efficiency 22% and Work done is 2510 Joules.

The efficiency is written as,

η= W / Qs.

The work done is W= Qs - Qr, where Qr is the rejected heat.

The heat rejected can be represented as

Qr = W ( 1/η -1)

Substituting the value into the equation, we get the rejected heat.

Qr = 2510 (1/0.22 -1)

Qr = 8900 Joules.

Thus, the heat rejected by the engine is 8900 Joules.

Learn more about efficiency.

#SPJ2

Answer: hello tables and data related to your question is missing attached below are the missing data

answer:

a) I = I₁ = I₂ = I₃ = 0.484 mA

b) I₁ =  0.016 amps

   I₂ =  0.0016 amps

   I₃ = 7.27 * 10^-4 amps

c)  I₁ = 1.43 * 10^-3 amp

    I₂ =  0.65 * 10^-3 amps

Explanation:

A) magnitude of current for Part 1

Resistors are connected in series

Req = r1 + r2 + r3

       = 3300 Ω  ( value gotten from table 1 ) ,

          V = 1.6 V ( value gotten from table )

hence I ( current ) = V / Req = 1.6 / 3300 = 0.484 mA

The magnitude of current is the same in the circuit

Vi = I * Ri

B) magnitude of current for part 2

Resistors are connected in parallel

V = 1.6 volts

Req = [ ( R1 * R2 / R1 + R2 ) * R3 / ( R1 * R2 / R1 + R2 ) +  R3 ]

      = [ ( 100 * 1000 / 100 + 1000) * 2200 / ( 100 * 1000 / 100 + 1000 ) + 2200]

      = 87.30 Ω

For a parallel circuit the current flow through each resistor is different

hence the magnitude of the currents are

I₁ = V / R1 = 1.6 / 100 = 0.016 amps

I₂ = V / R2 = 1.6 / 1000 = 0.0016 amps

I₃ = V / R3 = 1.6 / 2200 = 7.27 * 10^-4 amps

C) magnitude of current for part 3

Resistors are connected in combination

V = 1.6 volts

Req = R1 + ( R2 * R3 / R2 + R3 )

       = 766.66 Ω

Total current ( I ) = V / Req = 1.6 / 766.66 = 2.08 * 10^-3 amps

magnitude of currents

I₁ = ( I * R3 ) / ( R2 + R3 ) = 1.43 * 10^-3 amps

I₂ = ( I * R2 ) / ( R2 + R3 ) = 0.65 * 10^-3 amps

Answer:

The right solution is "[tex]4.5\times 10^{-10} \ Cm[/tex]".

Explanation:

Given that,

q = 0.50 nC

d = 900 mm

As we know,

⇒ [tex]P=qd[/tex]

By putting the values, we get

⇒     [tex]=0.50\times 900[/tex]

⇒     [tex]=(0.50\times 10^{-9})\times 0.9[/tex]

⇒     [tex]=4.5\times 10^{-10} \ Cm[/tex]  

Answer:

The dipole moment is 4.5 x 10^-10 Cm.

Explanation:

Charge on each ball, q = 0.5 nC

Length, L = 900 mm = 0.9 m

The dipole moment is defined as the product of either charge and the distance between them.

It is a vector quantity and the direction is from negative charge to the positive charge.

The dipole moment is

[tex]p = q L\\\\p = 0.5 \times 10^{-9}\times 0.9\\\\p = 4.5\times 10^{-10} Cm[/tex]

Answer:

D

Explanation:

This is a great way to manage health.

A would be avoiding everything which isnt good.

B. would be emotionally draining and damaging to bottle feelings and ignore them.

C. is unhealthy to not exercise and eat food while doing nothing.

Answer:

The current across the resistance is 0.011 A.

Explanation:

Total resistance, R = 25 ohms

Total current, I = 100 mA = 0.1 A

Let the voltage is V.

By the Ohm's law

V = I R

V = 0.1 x 25 = 2.5 V

Now the resistance is R' = 220 ohm

As they are in parallel so the voltage is same. Let the current is I'.

V = I' x R'

2.5 = I' x 220

I' = 0.011 A

Answer:

Tempered glass

Explanation:

When warmed, an amorphous substance has a non-crystalline architecture that differentiates from its isochemical liquid, but this does not go through structural breakdown or the glass transition.

Answer:

c)  N_s / N_p = 115.15

Explanation:

Let's look for the voltage in the secondary, they do not indicate the power dissipated

          P = V_s i

          V_s = P / i

          V_s = 76 / 5.5 10⁻³

          V_s = 13.818 10³ V

the relationship between the primary and secondary of a transformer is

           [tex]\frac{V_p}{N_p} = \frac{V_s}{N_s}[/tex]

           [tex]\frac{N_s}{N_p} = \frac{V_s}{V_p}[/tex]

           Ns / Np = 13,818 10³ /120

           N_s / N_p = 115.15

Answer:

temperature

Explanation:

temperature change forms different elements and different element sustain different colour

Answer:

Due to the applied filed the electrons move in a particular direction.

Explanation:

Initially when the switch is off, the free electrons move here and there in any random directions in the conductor with the random speeds called thermal velocity.  So, tat the net flow is almost zero.

When the battery is connected is switch is ON, the random motion of the electrons aligned in a particular direction due to the force applied by the electric filed, so the net flow is not zero it increases and thus the current flow.

[tex]E_0=1.5033×10^{-10}\:\text{J}[/tex]

Explanation:

The rest energy [tex]E_0[/tex] of a proton of mass [tex]m_p[/tex] is given by

[tex]E_0 = m_pc^2[/tex]

[tex]\:\:\:\:\:\:\:=(1.6726×10^{-27}\:\text{kg})(2.9979×10^8\:\text{m/s})^2[/tex]

[tex]\:\:\:\:\:\:\:=1.5033×10^{-10}\:\text{J}[/tex]

Answer:

false.

Explanation:

Ok, we define average velocity as the sum of the initial and final velocity divided by two.

Remember that the velocity is a vector, so it has a direction.

Then when she goes from the 1st end to the other, the velocity is positive

When she goes back, the velocity is negative

if both cases the magnitude of the velocity, the speed, is the same, then the average velocity is:

AV = (V + (-V))/2  = 0

While the average speed is the quotient between the total distance traveled (twice the length of the pool) and the time it took to travel it.

So we already can see that the average velocity will not be equal to half of the average speed.

The statement is false

Solids cannot diffuse.

Answer:

true

Explanation:

im not sure please dont attack me

Answer:

Greatest potential: moment before being dropped

Zero Kinetic: when it comes to rest

Greatest Kinetic: moment before first bounce

Explanation:

Answer:

[tex]P=17658Pa[/tex]

Explanation:

From the question we are told that:

Dimension

 [tex]L*B=27.0*8.9[/tex]

Depth [tex]d=1.8m[/tex]

Generally the equation for Volume of water is mathematically given by

 [tex]V=L*B*D[/tex]

 [tex]V=27.0*8.9*1.8[/tex]

 [tex]V=432.54m^3[/tex]

Therefore

Force at the bottom of the Pool

 [tex]F=\rho Vg[/tex]

Where

 [tex]\rho \ density\ of \ water(1000kg/m^3)[/tex]

 [tex]F=1000*432.54m^3*9.81[/tex]

 [tex]F=4.2*10^{6}N[/tex]

Generally the equation for Pressure at the bottom is mathematically given by

 [tex]P=\frac{Forece }{Area}[/tex]

 [tex]P=\frac{4.2*10^{6}N}{27.0*8.9}[/tex]

 [tex]P=17658Pa[/tex]

Answer:

n × t_1/2

Exmplanation:

The age of meteorite is calculated by multiplying it's quantity n with the half life . This means that the formula is for age of this meteorite is;

Age of meteorite= n × t_1/2

where;

n = quantity of the meteorite

t_/2 = half life of the meteorite

Thus:

The correct formula is; n × t_1/2

Answer: a rippling fountain

Explanation: diffuse reflection happens on rough surfaces, so using the process of elimination, that leaves us with b, a rippling fountain (I also just took this test I'm pretty sure I'm right)

Answer:

[tex]X=0.0389m[/tex]

Explanation:

From the question we are told that:

Period of spring [tex]T_s=2.25s[/tex]

Initial Position of Mass [tex]x=0.0480m[/tex]

Final Mass period [tex]T_f=5.85s[/tex]

Generally the equation for the Mass location is mathematically given by

[tex]X=xcos*\frac{2\pi T_s}{T_f}[/tex]

[tex]X=0.048*cos*\frac{2\pi 5.85}{2.25}[/tex]

[tex]X=0.0389m[/tex]

Answer:

0.857 cm

Explanation:

We are given that:

The focal length for a convex lens to be (f) = 1.5cm

The object distance (u) = - 2.0 cm

We are to determine the image distance (v) = ??? cm

By applying the lens formula:

[tex]\dfrac{1}{f} = \dfrac{1}{u}+\dfrac{1}{v}[/tex]

By rearrangement and making (v) the subject of the above formula:

[tex]v = \dfrac{uf}{u-f}[/tex]

replacing the given values:

[tex]v = \dfrac{(-2.0)(1.5)}{(-2.0 -1.5)}[/tex]

[tex]v = \dfrac{-3.0}{(-3.5)}[/tex]

v = 0.857 cm

Answer:

-45,597.07

Explanation:

if not in scientific calculator and yung answer nung sa scientific sa comment na lang dinadownload ko ka eh

Answer:

A) 8GMm/d^2

Explanation:

We are given that

[tex]m_1=M[/tex]

[tex]m_2=3M[/tex]

[tex]m_3=m[/tex]

Distance between m1 and m2=d

Distance of object of mass m from m1 and m2=d/2

Gravitational force formula

[tex]F=\frac{Gm_1m_2}{r^2}[/tex]

Using the formula

Force acting between m and M is given by

[tex]F_1=\frac{GmM}{d^2/4}[/tex]

Force acting between m and 3M is given by

[tex]F_2=\frac{Gm(3M)}{d^2/4}[/tex]

Now, net force acting on  object of mass is given by

[tex]F=F_2-F_1[/tex]

[tex]F=\frac{Gm(3M)}{d^2/4}-\frac{GmM}{d^2/4}[/tex]

[tex]F=\frac{12GmM}{d^2}-\frac{4GmM}{d^2}[/tex]

[tex]F=\frac{12GmM-4GmM}{d^2}[/tex]

[tex]F=\frac{8GmM}{d^2}[/tex]

Hence, the magnitude of the force on the object with mass m=[tex]\frac{8GmM}{d^2}[/tex]

Option A is correct.

Answer:

elastic energy

Explanation:

When a gymnast falls on a trampoline from a height, after coming in contact with the trampoline, both the gymnast and the trampoline start to move down due to the elastic property of the trampoline.

During this stretching of the trampoline there comes a maximum point up to which the trampoline is stretched. At this point, both the kinetic energy and the gravitational potential energy of the gymnast are zero due to zero speed and zero height, respectively.

The only energy stored in the gymnast's body at this point is the elastic potential energy due to stretching of the trampoline. Hence,the correct option is:

elastic energy

Answer:

1

Explanation:

Electrolysis is the passing of an current through a conducting solution, when the occurs, a chemical reaction takes place.

Heating a chemical will always cause a chemical reaction, which is why 3 is also correct

Some information as to why 2 is NOT correct.

2 is NOT a chemical reaction, but rather a process of physical separation. It uses selective boiling and condensation, but is not considered a chemical reaction.

as with 3, heating is not considered a chemical reaction, but rather a physical temperature change. This is always what it is considered to be (e.g boiling water is a physical temperature change, not a chemical reaction)

Hope this helps.

Hope this helps.

Answer:

a)   p = 95.66 cm, b) p = 93.13 cm

Explanation:

For this problem we use the  constructor equation

         [tex]\frac{1}{f} = \frac{1}{p} + \frac{1}{q}[/tex]

where f is the focal length, p and q are the distances to the object and the image, respectively

the power of the lens is

         P = 1 / f

         f = 1 / P

         f = 1 / 2.25

         f = 0.4444 m

the distance to the object is

         [tex]\frac{1}{p} = \frac{1}{f} -\frac{1}{q}[/tex]

the distance to the image is

          q = 85 -2

           q = 83 cm

we must have all the magnitudes in the same units

           f = 0.4444 m = 44.44 cm

we calculate

           [tex]\frac{1}{p} = \frac{1}{44.44} - \frac{1}{83}[/tex]

           1 / p = 0.010454

            p = 95.66 cm

b) if they were contact lenses

            q = 85 cm

            [tex]\frac{1}{p} = \frac{1}{44.44} - \frac{1}{85}[/tex]

             1 / p = 0.107375

             p = 93.13 cm

Answer:

Explanation:

From the information given:

The motional emf can be computed by using the formula:

[tex]E = L^{\to}*(V^\to*\beta^{\to})[/tex]

[tex]E = L^{\to}*((x+y+z)*\beta^{\to})[/tex]

[tex]E = 0.50*((18\hat i+24 \hat j +72 \hat k )*0.0800)[/tex]

[tex]E = 0.50*((18*0.800)\hat k +0j+(72*0.080) \hat -i ))[/tex]

[tex]E = 0.50*((18*0.800)[/tex]

E = 0.72 volts

According to the question, suppose the wire segment was parallel, there will no be any emf induced since the magnetic field is present along the y-axis.

As such, for any motional emf should be induced, the magnetic field, length, and velocity are required to be perpendicular to one another .

Then the motional emf will be:

[tex]E = 0.50 \hat j *((18*0.800)\hat k -(72*0.080) \hat i ))[/tex]

E = 0 (zero)

5 9 . 4

- 3 7 . 2

2 2 . 2

Explanation:

Use the algorithm method.

5 9 . 4

- 3 7 . 2

2 2 . 2

2 Therefore, 59.4-37.2=22.259.4−37.2=22.2.

22.2

22.2

Speed= distance/time

Or time = distance/speed

According to your question

Speed=15m/s

and. Distance=1.2km. ,we must change kilometer in meter because given speed is in m/s

D= 1.2km = 1.2×1000m =1200meter

Time = distance/ speed

1200/15 =80second

Or. 1min and 20 sec will be your answer.