Answer:
hdwhifniuewohfoyyhyeiudhwbwuxvgusvfgcvxg
Explanation:
Find Ic(t),
If Vs(t)=8sin(4t+180°) V
3
د3
lic
62.5met
O 2.5cos(4t+53.1) A
O scos(4x+53.1°) A
O 2.5cos(4t+143°) A
Oscos(4t+143) A
Answer:
the answer is equal to 2.5cos(4t +53.1)
what is the difference between a series circuit and a parallel circuit?
Answer:
In a parallel circuit, the voltage across each of the components is the same, and the total current is the sum of the currents flowing through each component. ... In a series circuit, every device must function for the circuit to be complete. If one bulb burns out in a series circuit, the entire circuit is broken.
Explanation:
A s100 N m torque is applied to a 1-m-long, solid round steel shaft. Design it to limit its angular deflection 2°, if shear modulus of elasticity 80 GPa and to determine the fatigue strength of the material.
Answer:
assuming factor of safety of 2
Se = 118.858 MPa
Explanation:
Torque = ± 100 N m
length of solid round steel shaft = 1-m
Angular deflection = 2°
shear modulus of elasticity = 80 GPa
Calculate Fatigue strength of material
apply Von-miss effective stress rule to determine the Von mises stress
max torque = 100 + 0
assuming a factor of safety of 2
Se(fatigue strength of material ) = Von mises stress * Fs
= 59.429 * 2 = 118.858 MPa
1.1.2
Energy
1.1.3
Mass
1.1.4
Temperature
Power
1.1.5
1.2 State Ohm's law
1.3 State Joule's law
1.5 Name four factors that9 determine the resistance of the material
1.6 What is the SI Unit for current?
QUESTION 2
Answer:
the energy is sgdrh35679
What is a SAFETY CHECK
Answer:
Safety check is defined as rounding to make sure that the patients and the milieu (patients living quarters) is secured and free of harmful items that can be used to hurt someone.
SN1 reactions usually proceed with ________. A) equal amounts of inversion and retention at the center undergoing substitution B) slightly more inversion than retention at the center undergoing substitution C) slightly more retention then inversion at the center undergoing substitution D) complete inversion at the center undergoing substitution E) complete retention at the center undergoing substitution complete retention at the center undergoing substitution slightly more retention then inversion at the center undergoing substitution complete inversion at the center undergoing substitution equal amounts of inversion and retention at the center undergoing substitution slightly more inversion than retention at the center undergoing substitution
Answer:
equal amounts of inversion and retention at the center undergoing substitution
Explanation:
In an SN1 reaction, the rate determining step is the formation of a carbonation which is flat and planar.
This means that both faces of the carbo cation are equally available for attack by the nucleophile.
Attack on either of the faces may occur equally thereby yielding a racemic mixture.
For automobile engines, identify the best choice of motor oil.
A. High viscosity for Maine in the winter and low viscosity for Florida in the summer.
B. Low viscosity for Maine in the winter and low viscosity for Florida in the summer.
C. Low viscosity for Maine in the winter and high viscosity for Florida in the summer.
D. High viscosity for Maine in the winter and high viscosity for Florida in the summer.
E. It does not matter what the rating is for the motor oil.
Answer:
C. Low viscosity for Maine in the winter and high viscosity for Florida in the summer.
Explanation:
The choice of motor oil or engine oil depends on the type of engine and also on the type of climate on which the engine runs.
In winter climates, we should use oil with low viscosity as at lower temperatures, the it flows more readily if its viscosity is low.
But the summer season needs a relatively thicker oil so as to reduce the thinning effect of the oil out of the engine.
Thus for Maine in the winter season, we need a low viscosity oil and for Florida a high viscosity oil in the summer season.
Therefore, option (c) is correct.
Your new team is working hard, but they are all less experienced than you and don't complete their tasks as quickly.What would you be most and least likely to do? (A). Reach out to your manager to discuss the situation.Try to identify the best way to support the new associates. (B).Remind your coworkers of performance expectations and that they need to be working harder to complete tasks. (C). Offer to help others complete their tasks; observe their work process and provide some tips that might help them. (D). Give your coworkers more time to figure out how to do the task; they likely just need more practice with what they've already learned.
