The average power consumption for Eager WiFi, Lazy WiFi, Eager 4G, and Lazy 4G Split is maintained by Screen Mode.
Why reducing leads to increasing wages?Reducing such a need to move in between multiple tabs, the split-screen has been valuable for increasing wages. In the several instances running a two or more desktop system will allow different programs to run throughout multiple devices. That works with the same process on both PC and laptop monitors.
Just display them side by side, instead of the switching among both the apps that has been used frequently. In this phase, an app that the snap to either left or right occupies a third of the display, and yet another app holds the two-thirds remaining. It refers to Split-Screen Mode.
Similarly, assume that the communication radio for 4G has a power consumption of 190 mW when active and 25 mW when idle. The Idle Power of the CPU is 7 mW, whereas the Active Power of the CPU is 5 mW per unit utilization.
Therefore, The average power consumption for Eager WiFi, Lazy WiFi, Eager 4G, and Lazy 4G Split is maintained by Screen Mode.
Learn more about average power on:
https://brainly.com/question/14831024
#SPJ2
A flow inside a centrifuge can be approximated by a combination of a central cylinder and a radial line source flow, giving the following potential function:
Ø= a2/r -cosØ + aßlnr = r
Where a is the radius of the central base of the centrifuge and ß is a constant.
a) Provide expressions for the velocities Vr and vo .
b) Find the expression for the stream function.
Answer:
a) Vr = - a^2/r cosθ + aß / r
Vθ = 1/r [ -a^2/r * sinθ ]
b) attached below
Explanation:
potential function
Ø= a^2 /r cosØ + aßlnr ----- ( 1 )
a = radius , ß = constant
a) Expressions for Vr and Vθ
Vr = dØ / dr ----- ( 2 )
hence expression : Vr = - a^2/r cosθ + aß / r
Vθ = 1/r dØ / dθ ------ ( 3 )
back to equation 1
dØ / dr = - a^2/r sinθ + 0 --- ( 4 )
Resolving equations 3 and 4
Vθ = 1/r [ -a^2/r * sinθ ]
b) expression for stream function
attached below
Steam enters an adiabatic turbine at 6 MPa, 600°C, and 80 m/s and leaves at 50 kPa, 100°C, and 140 m/s. If the power output of the turbine is 5 MW, determine (a) the reversible power output and (b) the second-law efficiency of the turbine. Assume the surroundings to be at 25°C.
Answer:
(a) the reversible power output of turbine is 5810 kw
(b) The second-law efficiency of he turbine = 86.05%
Explanation:
In state 1: the steam has a pressure of 6 MPa and 600°C. Obtain the enthalpy and entropy at this state.
h1 = 3658 kJ/kg s1=7.167 kJ/kgK
In state 2: the steam has a pressure of 50 kPa and 100°C. Obtain the enthalpy and entropy at this state
h2 = 2682kl/kg S2= 7.694 kJ/kg
Assuming that the energy balance equation given
Wout=m [h1-h2+(v1²-v2²) /2]
Let
W =5 MW
V1= 80 m/s V2= 140 m/s
h1 = 3658kJ/kg h2 = 2682 kJ/kg
∴5 MW x1000 kW/ 1 MW =m [(3658-2682)+ ((80m/s)²-(140m/s)²)/2](1N /1kg m/ s²) *(1KJ/1000 Nm)
m = 5.158kg/s
Consider the energy balance equation given
Wrev,out =Wout-mT0(s1-s2)
Substitute Wout =5 MW m = 5.158kg/s 7
s1= 7.167 kJ/kg-K s2= 7.694kJ/kg-K and 25°C .
Wrev,out=(5 MW x 1000 kW /1 MW) -5.158x(273+25) Kx(7.167-7.694)
= 5810 kW
(a) Therefore, the reversible power output of turbine is 5810 kw.
The given values of quantities were substituted and the reversible power output are calculated.
(b) Calculating the second law efficiency of the turbine:
η=Wout/W rev,out
Let Wout = 5 MW and Wrev,out = 5810 kW
η=(5 MW x 1000 kW)/(1 MW *5810)
η= 86.05%
A 20-mm-diameter steel bar is to be used as a torsion spring. If the torsional stress in the bar is not to exceed 110 MPa when one end is twisted through an angle of 15°, what must be the length of the bar?
Answer:
1.887 m
Explanation:
(15 *pi)/180
= 0.2618 rad
Polar moment
= Pi*d⁴/32
= (22/7*20⁴)/32
= 15707.96
Torque on shaft
= ((22/7)*20³*110)/16
= 172857.14
= 172.8nm
Shear modulus
G = 79.3
L = Gjθ/T
= 79.3x10⁹x(1.571*10^-8)x0.2618/172.8
= 1.887 m
The length of the bar is therefore 1.887 meters
The system is initially moving with the cable taut, the 15-kg block moving down the rough incline with a speed of 0.080 m/s, and the spring stretched 39 mm. By the method of this article, (a) determine the velocity v of the block after it has traveled 99 mm, and (b) calculate the distance d traveled by the block before it comes to rest.
Solution :
The spring is expanded by 2 times of the block when it moves down an inclined by x times.
Here, [tex]$x_1$[/tex] = 39 mm
[tex]x_2[/tex] = 225 mm
a). From the work energy principal,
Work forces = kinetic energy
[tex]$(mg \sin 50^\circ)\times \frac{99}{1000}-(\mu_k mg \cos 50^\circ) \times \frac{99}{1000} -\frac{1}{2}k(0.225^2 - 0.039^2)=\frac{1}{2}m(V^2_2-0.08^2)$[/tex]
[tex]$(112.6 \times 0.099)-(14.17 \times 0.099)-4.91= 7.5(V^2_2-0.08^2)$[/tex]
[tex]$9.75= 7.5(V^2_2-0.08^2)$[/tex]
[tex]$1.3= V^2_2-0.08^2$[/tex]
[tex]$V_2=1.14\ m/s$[/tex]
b). calculating the distance travelled by the block before it comes to rest.
Substitute the value of [tex]V_2[/tex] in (1),
[tex]$-(\mu_kmg \cos 50^\circ)x + (mg \sin 50^\circ)x-\frac{1}{2}k\left( ( 2x+0.039)^2 - 0.039^2\right)= -\frac{1}{2}m(0.08)^2$[/tex]
[tex]$-14.17x+112.6x - 100(4x^2+0.156x)=-0.048$[/tex]
[tex]$98.43x - 100(4x^2+0.156x)+0.048=0$[/tex]
[tex]$98.43x - 400x^2-15.6x+0.048=0$[/tex]
[tex]$82.83x - 400x^2+0.048=0$[/tex]
[tex]$ 400x^2- 82.83x-0.048=0$[/tex]
x = 0.20 m
The heat transfer surface area of a fin is equal to the sum of all surfaces of the fin exposed to the surrounding medium, including the surface area of the fin tip. Under what conditions can we neglect heat transfer from the fin tip?
Answer:
The explanation according to the given query is summarized in the explanation segment below.
Explanation:
If somehow the fin has become too lengthy, this same fin tip temperature approaches the temperature gradient and maybe we'll ignore heat transmission out from end tips.Additionally, effective heat transmission as well from the tip could be ignored unless the end tip surface is relatively tiny throughout comparison to its overall surface.Your shifts productivity is Slow because one person is not pulling his share. The rest of the team is Getting upset.
Answer:
you are right but then you ddnt ask a question
A levee will be constructed to provide some flood protection for a residential area. The residences are willing to accept a one-in-five chance that the levee will be overtopped in the next 15 years. Assuming that the annual peak streamflow follows a lognormal distribution with a log10(Q[ft3/s]) mean and standard deviation of 1.835 and 0.65 respectively, what is the design flow in ft3/s?
Answer:
1709.07 ft^3/s
Explanation:
Annual peak streamflow = Log10(Q [ft^3/s] )
mean = 1.835
standard deviation = 0.65
Probability of levee been overtopped in the next 15 years = 1/5
Determine the design flow ins ft^3/s
P₁₅ = 1 - ( q )^15 = 1 - ( 1 - 1/T )^15 = 0.2
∴ T = 67.72 years
Q₁₅ = 1 - 0.2 = 0.8
Applying Lognormal distribution : Zt = mean + ( K₂ * std ) --- ( 1 )
K₂ = 2.054 + ( 67.72 - 50 ) / ( 100 - 50 ) * ( 2.326 - 2.054 )
= 2.1504
back to equation 1
Zt = 1.835 + ( 2.1504 * 0.65 ) = 3.23276
hence:
Log₁₀ ( Qt(ft^3/s) ) = Zt = 3.23276
hence ; Qt = 10^3.23276
= 1709.07 ft^3/s
Water is pumped steadily through a 0.10-m diameter pipe from one closed pressurized tank to another tank. The pump adds 4.0 kW of energy to the water and the head loss of the flow is 10 m. Determine the velocity of the water leaving the pump and discharging into tank B.
Complete Question
Complete Question is attached below.
Answer:
[tex]V'=5m/s[/tex]
Explanation:
From the question we are told that:
Diameter [tex]d=0.10m[/tex]
Power [tex]P=4.0kW[/tex]
Head loss [tex]\mu=10m[/tex]
[tex]\frac{P_1}{\rho g}+\frac{V_1^2}{2g}+Z_1+H_m=\frac{P_2}{\rho g}+\frac{V_2^2}{2g}+Z_2+\mu[/tex]
[tex]\frac{300*10^3}{\rho g}+35+Hm=\frac{500*10^3}{\rho g}+15+10[/tex]
[tex]H_m=(\frac{200*10^3}{1000*9.8}-10)[/tex]
[tex]H_m=10.39m[/tex]
Generally the equation for Power is mathematically given by
[tex]P=\rho gQH_m[/tex]
Therefore
[tex]Q=\frac{P}{\rho g H_m}[/tex]
[tex]Q=\frac{4*10^4}{1000*9.81*10.9}[/tex]
[tex]Q=0.03935m^3/sec[/tex]
Since
[tex]Q=AV'[/tex]
Where
[tex]A=\pi r^2\\A=3.142 (0.05)^2[/tex]
[tex]A=7.85*10^{-3}[/tex]
Therefore
[tex]V'=\frac{0.03935m^3/sec}{7.85*10^{-3}}[/tex]
[tex]V'=5m/s[/tex]
Activity 1. Fill the blank with the correct answer. Write your answer on the blank. 1. ___________________ is a regular pattern of dots displayed on the screen which acts as a visual aid and also used to define the extent of your drawing. 2. Ortho is short for ___________________, which means either vertical or horizontal. 3. Tangent is a point where two _______________________ meet at just a single point. 4. If you want to create a new drawing, simply press ___________________ for the short cut key. 5. There are _______________Osnap that can help you performs your task easier.
Answer:
1. Drawing grid.
2. Orthogonal.
3. Geometries.
4. CTRL+N.
5. Thirteen (13).
Explanation:
CAD is an acronym for computer aided design and it is typically used for designing the graphical representation of a building plan. An example of a computer aided design (CAD) software is AutoCAD.
Some of the features of an AutoCAD software are;
1. Drawing grid: is a regular pattern of dots displayed on the screen of an AutoCAD software, which acts as a visual aid and it's also used to define the extent of a drawing.
2. Ortho is short or an abbreviation for orthogonal, which means either vertical or horizontal.
3. Tangent is a point where two geometries meet at just a single point.
4. If you want to create a new drawing, simply press CTRL+N for the short cut key.
5. There are thirteen object snaps (Osnap) that can help you perform your task on AutoCAD easily. The 13 object snaps (Osnap) are; Endpoint, Midpoint, Apparent intersect, Intersection, Quadrant, Extension, Tangent, Center, Insert, Perpendicular, Node, Parallel, and Nearest.
) Please label the following statements as either True (T) or False (F). (a) In general, the greater the % of cold work, the smaller the recrystallization grain size. (b) The higher the annealing temperature, the smaller the recrystallization grain size. (c) The greater the % of cold work, the lower the recrystallization temperature.
Answer:
A. This option is true
B. This option is false
C. This option is true
Explanation:
A. Generally speaking, the greater percentage of cold, the recrystallization grain size would turn out to be smaller. Therefore this true.
B. A higher annealing temperature does not result in smaller recrystallization grain size. Therefore this is false.
C. As the percentage of cold work is greater, the recrystallization temperature would tend to be lower. Therefore this is true.
6. When the engine stalls or the power unit fails, on a car with power
brakes, the service brake pedal will
A. Take about the same amount of pressure
B. Take more pressure to stop
C. Take less pressure to stop
D. Become locked in place and no longer help stop the car
A work-mode-choice model is developed from data acquired in the field in order to determine the probabilities of individual travelers selecting various modes. The mode choices include automobile drive-alone (DL), automobile shared-ride (SR), and bus (B). The utility functions are estimated as follows:
UDL = 2.6 - 0.3 (costDL) - 0.02 (travel timeDL)
USR = 0.7 - 0.3 (costSR) - 0.04 (travel timeSR)
UB = -0.3 (costB) - 0.01 (travel timeB)
where cost is in dollars and time is in minutes. The cost of driving an automobile is exist5.50 with a travel time of 21 minutes, while the bus fare is exist1.25 with a travel time of 27 minutes. How many people will use the shared-ride mode from a community of 4500 workers, assuming the shared-ride option always consists of three individuals sharing costs equally?
a. 314
b. 828
c. 866
d. 2805
Answer:
b. 828
Explanation:
UDL = 2.6 - 0.3 [5.5] - 0.02 [ 21 ] = 0.53
USR = 0.7 - 0.3 [5.5 / 2 ] - 0.04 [ 21 ] = -0.69
UB = -0.3 [ 1.25 ] - 0.01 = -0.645
Psr = [tex]\frac{e^{-0.53} }{e^{-0.53} + e^{-0.69} + e^{-0.645} }[/tex]
Solving the equation we get 0.184.
Number of people who will take shared ride is:
0.184 * 4500 = 828 approximately.
Determine the pressure difference in N/m2,between two points 800m apart in horizontal pipe-line,150 mm diameter, discharging water at the rate of 12.5litres per second. Take the frictional coefficient ,f, as being 0.008
Answer: [tex]10.631\times 10^3\ N/m^2[/tex]
Explanation:
Given
Discharge is [tex]Q=12.5\ L[/tex]
Diameter of pipe [tex]d=150\ mm[/tex]
Distance between two ends of pipe [tex]L=800\ m[/tex]
friction factor [tex]f=0.008[/tex]
Average velocity is given by
[tex]\Rightarrow v_{avg}=\dfrac{12.5\times 10^{-3}}{\frac{\pi }{4}(0.15)^2}\\\\\Rightarrow v_{avg}=\dfrac{15.9134\times 10^{-3}}{2.25\times 10^{-2}}\\\\\Rightarrow v_{avg}=7.07\times 10^{-1}\\\Rightarrow v_{avg}=0.707\ m/s[/tex]
Pressure difference is given by
[tex]\Rightarrow \Delta P=f\ \dfrac{L}{d}\dfrac{\rho v_{avg}^2}{2}\\\\\Rightarrow \Delta P=0.008\times \dfrac{800}{0.15}\times \dfrac{997\times (0.707)^2}{2}\\\\\Rightarrow \Delta P=10,631.45\ N/m^2\\\Rightarrow \Delta P=10.631\ kPa[/tex]
Select the correct statement(s) regarding network physical and logical topologies.
a. While logical topologies can be configured in star, ring, bus, and tree configurations, the physical topology must always be in a full-mesh topology
b. logical topologies always incorporate centralized access, whereas physical topologies are always configured as a distributed access network
c. the physical topology addresses how devices are connected, while a logical topology addresses how devices actually communicate to one another
d. all statements are correct
Answer:
The physical topology addresses how devices are connected, while a logical topology addresses how devices actually communicate to one another ( C )
Explanation:
Network physical is simply the process/method of connecting the Network using cables while Logical topology is the general architecture of the communication mechanism in the network for all nodes.
Hence The correct statement is the physical topology addresses how devices are connected, while a logical topology addresses how devices actually communicate to one another
In an international film festival, a penal of 11 judges is formed to judge the best film. At
last two films FA and FB were considered to be the best where the opinion of judges got
divided. Six judges where in favor of FA whereas five in favor of FB. A random sample
of five judges was drawn from the panel. Find the probability that out of five judges,
three are in favor of film FA.Enunciate demerits of classical probability.
Answer:
International Film Festival
Judging the best best film:
a. The probability that out of five judges (random sample), three are in favor of film FA is:
= 33%.
b. The demerits of classical probability are:
1. Classical probability can only be used with events that have definite numbers of possible outcomes.
2. Classical probability can only handle events where each outcome is equally likely.
3. Classical probability is based on the assumption of linear relationship (which is not always true in real life) between the latent variable and observed scores.
Explanation:
a) Number of judges = 11
Number of judges in favor of FA film = 6
Number of judges in favor of FB film = 5
Probability of judges in favor of FA film = 6/11
Probability of judges in favor of FB film = 5/11
Random sample of judges = 5
Probability that out of five judges, three are in favor of film FA = 3/5 * 6/11
= 18/55
= 33%
b) Classical probability is the simple probability showing that each event has equal chance of happening. It can be contrasted with empirical probability that is obtained from experiments.
what type of slab and beam used in construction of space neddle
jrjrkeekkekekkwkkakkllalllalallalllalalaallalalaalalalalalallallallllallalalallaaallalallllllallllllllalaalalalaaaaalalaaaaaaalgjgiejxpwunfifjruritiririirieoeowowowowowowowowooeowowowoeeoeowowowowowowowoowowwowowowoozoeisiaokseekxidjdkdjfidjfjdjfjfjrifjrifjdirjdjrjfjrjfjrjfjrfuejwwuxmaneanfjkaosndjxieneamalhaqzeeshanvhorahfuensiwjakaksjdhfhfnfhfndjxnxmakaalalalwlwlwwow
A horizontal water jet impinges against a vertical flat plate at 30 ft/s and splashes off the sides in the verti- cal plane. If a horizontal force of 500 lbf is required to hold the plate against the water stream, determine the volume flow rate of the water.
Answer:
8.6 ft³/s
Explanation:
The force due to the water jet F = mv where m = mass flow rate = ρQ where ρ = density of water = 62.4 lbm/ft³ and Q = volume flow rate. v = velocity of water jet = 30 ft/s
So, F = mv
F = ρQv
making Q subject of the formula, we have
Q = F/ρv
Since F = force due to water jet = force needed to hold the plate against the water stream = 500 lbf = 500 × 1 lbf = 500 × 32.2 lbmft/s² = 16100 lbmft/s²
Since
Q = F/ρv
Substituting the values of the variables into the equation for Q, we have
Q = F/ρv
Q = 16100 lbmft/s²/(62.4 lbm/ft³ × 30 ft/s)
Q = 16100 lbmft/s²/1872 lbm/ft²s
Q = 8.6 ft³/s
So, the volume flow rate is 8.6 ft³/s.
The following measurements are taken on particular junction diodes for which V is the terminal voltage and I is the diode current. For each diode, estimate values of Is and the terminal voltage at 10% of the measured current.
(a) V = 0.700 V at I = 1.00 A.
(b) V = 0.650 V at I = 1.00 mA.
(c) V = 0.650 V at I = 10 mu A.
(d) V = 0.700V at I = 100 mA.
The values of Is and V are as: (a) [tex]Is = 2.34 \times 10^{-11} A[/tex] and V = 0.581 V. (b) [tex]Is = 4.56 \times 10^{-15} A[/tex] and V = 0.516 V. (c) [tex]Is = 1.18 \times 10^{-16} A\\[/tex] and V = 0.459 V. (d) [tex]Is = 2.34 \times 10^{-11} A[/tex] and V = 0.581 V.
The relation between the current and voltage of a diode is given by the Shockley diode equation. It is an exponential function and can be given by the following equation:
[tex]I = Is \times (e^{V/Vt} - 1)[/tex]
Where
I = currentV = voltageVt = thermal voltageIs = reverse saturation current.(a)
Given that:
V = 0.700 V
And I = 1.00 A.
Substituting these values in the equation above to get,
[tex]1.00 A = Is \times (e^{0.700 V / 0.025 V} - 1)\\Is = 2.34 \times 10^{-11} A[/tex]
The terminal voltage at 10% of the measured current can be found by substituting I = 0.1 A in the above equation and solving for V as:
V = 0.581 V.
(b)
Given that:
V = 0.650 V
And, I = 1.00 mA.
Substituting these values in the equation above to get,
[tex]1.00 mA = Is \times (e^{0.650 V / 0.025 V} - 1)\\ Is = 4.56 \times 10^{-15} A[/tex]
The terminal voltage at 10% of the measured current can be found by substituting I = 0.1 mA in the above equation and solving for V as:
V = 0.516 V.
(c)
Given that:
V = 0.650 V
And, I = 10 μA.
Substituting these values in the equation above to get,
[tex]10 \mu A = Is \times (e^{0.650 V / 0.025 V} - 1)\\Is = 1.18 \times 10^{-16} A[/tex]
The terminal voltage at 10% of the measured current can be found by substituting I = 1 μA in the above equation and solving for V as:
V = 0.459 V.
(d)
Given that:
V = 0.700 V
And, I = 100 mA.
Substituting these values in the equation above to get,
[tex]100 \ mA = Is \times (e^{0.700 V / 0.025 V} - 1)\\Is = 2.34 \times 10^{-11} A[/tex]
The terminal voltage at 10% of the measured current can be found by substituting I = 10 mA in the above equation and solving for V as:
V = 0.581 V.
So, the values of Is and V are as: (a) [tex]Is = 2.34 \times 10^{-11} A[/tex] and V = 0.581 V. (b) [tex]Is = 4.56 \times 10^{-15} A[/tex] and V = 0.516 V. (c) [tex]Is = 1.18 \times 10^{-16} A\\[/tex] and V = 0.459 V. (d) [tex]Is = 2.34 \times 10^{-11} A[/tex] and V = 0.581 V.
Learn more about Terminal voltage here:
https://brainly.com/question/34372613
#SPJ3
3-71A 20mm diameter steel bar is to be used as a torsion spring. If the torsional stress in the bar is not to exceed 110 MPa when one end is twisted through an angle of 15 degrees, what must be the length of the bar
Answer:
The right answer is "1.903 m".
Explanation:
Given that,
[tex]\tau =110 \ MPa[/tex]
[tex]G=80 \ GPa[/tex]
[tex]\Theta=15\times \frac{\pi}{180}[/tex]
[tex]=\frac{\pi}{12}[/tex]
[tex]d=20 \ mm[/tex]
As we know,
⇒ [tex]\frac{\tau}{r}=\frac{G \Theta}{L}[/tex]
Or,
⇒ [tex]L=\frac{G \theta r}{\tau}[/tex]
[tex]=\frac{80\times 10^3}{110}\times \frac{\pi}{12}\times 10[/tex]
[tex]=1903.9 \ mm[/tex]
or,
[tex]=1.903 \ m[/tex]
A 1m3 tank containing air at 25℃ and 500kPa is connected through a valve to
another tank containing 5kg of air at 35℃ and 200kPa. Now the valve is opened,
and the entire system is allowed to reach thermal equilibrium, which is at 20℃
(Take: Ru = 8.314 kJ / kg.K).
Answer:
The right answer is "2.2099 m³".
Explanation:
Given:
Mass,
m = 5 kg
Temperature,
T = 35℃
or,
= 35 + 273
Pressure,
P = 200 kPa
Gas constant,
R = 0.2870 kj/kgK
By using the ideal gas equation,
The volume will be:
⇒ [tex]PV=mRT[/tex]
or,
⇒ [tex]V=\frac{mRT}{P}[/tex]
By substituting the values, we get
[tex]=\frac{5(0.2870)(35+273)}{200}[/tex]
[tex]=\frac{441.98}{200}[/tex]
[tex]=2.2099 \ m^3[/tex]
Find the general solution of the given differential equation. Give the largest interval over which the general solution is defined. Determine whether there are any transient terms in the general solution.
x dx/dy−y=x^2sinx
Answer:
Interval: x∈ ( 0, ∞ )
There are no transient terms
Explanation:
x (dy/dx) – y= x^2sinx
Attached below is the detailed solution of the Given problem
There are no transient terms found in the general solution
Interval: x∈ ( 0, ∞ )
The temperature gradient in a spherical (or cylindrical) wall at steady state will always decrease (in magnitude) with increasing distance from the center (line), i.e. radial distance.
A. True
B. False
Answer:
True
Explanation:
Yes it is true that the Temperature gradient would also decrease with magnitude just as the distances rise from the centre line.
We have this cylinder equation as
[T1-T2 / ln(r1-r2)]2πKL
The radial distance is r2-r1
The gradient of temperature is T1-T2
From the equation,
The temperature gradient has a direct and proportional relationship to radial distance
T1-T2 ∝ ln(r2-r1)
1/T1-T2 = k(r2-r1)
This inverse relationship above confirms that the statement is true
bending stress distribution is a.rectangle b.parabolic c.curve d.i section
Set the leak rate to zero and choose a non-zero value for the proportional feedback gain.Restart the simulation and turn on the outflow valve.What happens to the liquid level in the tank?Repeat this process with higher and lower values for the proportional feedback gain.What happens when the proportional feedback gain is increased?What happens when it is decreased?Find the proportional gain that will reach steady state the quickest without oscillationin the state of the valve and restart the simulation.What is the system time constant, as determined from the tank level versus time plot.
Answer:
Explanation:
The proportional gain K is usually a fixed property of the controller . If proportional gain is increased , The sensitivity of the controller to error is increased but the stability is impaired. The system approaches the behaviour of on off controlled system and it response become oscillatory
Blocks A and B each have a mass m. Determine the largest horizontal force P which can be applied to B so that A will not move relative to B. All surfaces are smooth.
Answer:
The answer is "15 N".
Explanation:
Please find the complete question in the attached file.
In frame B:
For just slipping:
[tex]\to \frac{P}{2} \cos \theta =mg \sin \theta\\\\\to P=2 mg \tan \theta \\\\[/tex]
[tex]=2 \times 1 \times g \times \tan 37^{\circ}\\\\ =2 \times 10 \times \frac{3}{4}\\\\ =15 \ N[/tex]
In low speed subsonic wind tunnels, the value of test section velocity can be controlled by adjusting the pressure difference between the inlet and test-section for a fixed ratio of inlet-to-test section cross-sectional area.
a. True
b. false
Answer:
Hence the given statement is false.
Explanation:
For low-speed subsonic wind tunnels, the air density remains nearly constant decreasing the cross-section area cause the flow to extend velocity, and reduce pressure. Similarly increasing the world cause to decrease and therefore the pressure to extend.
The speed within the test section is decided by the planning of the tunnel.
Thus by adjusting the pressure difference won't change the worth of test section velocity.
Answer:
The given statement is false .
Given resistance 30ohms Inductance 200mH is connected to a 230v,50hZ supply. Impedance 69.6ohms Calculate current consumed?
Answer:
the current consumed is 3.3 A
Explanation:
Given;
resistance, R = 30 ohms
inductance, L = 200 mH
Voltage supply, V = 230 V
frequency of the coil, f = 50 Hz
impedance, Z = 69.6 Ohms
The current consumed is calculated as;
[tex]I = \frac{V}{Z} \\\\I = \frac{230}{69.6} \\\\I = 3.3 \ A[/tex]
Therefore, the current consumed is 3.3 A
(50 POINTS) How many people use pipes in the world? How do you know this?
Answer:
7.9 billion people
Explanation:
Cite another example of information technology companies pushing the boundaries of privacy issues; apologizing, and then pushing again once scandal dies down. As long as the controversy fades, is there anything unethical about such a strategy?
Answer:
Explanation:
Tech Social Media giant FB is one of those companies. Not long ago the ceo was brought to court to accusations that his company was selling user data. Turns out this is true and they are selling their users private data to companies all over the word. Once the news turned to something else, people focused on something new but the company still continues to sell it's users data the same as before. This is completely unethical as the information belongs to the user and they are not getting anything while the corporation is profiting.
what is the best glide speed for your training airplane
1.5 nautical miles per 1,000 feet
