Answer:
Mass = 64,870,000,000 kilograms
Explanation:
Given the following data;
Density = 998 kg/m³
Volume = 6,500,000 m³
To find the mass of water in the reservoir;
Density can be defined as mass all over the volume of an object.
Simply stated, density is mass per unit volume of an object.
Mathematically, density is given by the equation;
Density = mass/volume
Making mass the subject of formula, we have;
Mass = density * volume
Mass = 998 * 6,500,000
Mass = 64,870,000,000 kilograms
Using atomic weight crystal structure and atomic radius data tabulated inside the front cover compute the theoritical densities of alminuim ,nikel......
Question
Using atomic weight, crystal structure, and atomic radius data tabulated inside the front cover of thebook, compute the theoretical densities of aluminum (Al), nickel (Ni), magnesium (Mg), and tungsten (W), and thencompare these values with the measured densities listed in this same table. The c/a ratio for magnesium is 1.624.
Explanation:
The Sun is an enormous ball of gas. Left to itself, a ball of so many atoms should collapse under its own tremendous gravity. Why is our Sun not collapsing
Answer:
Nuclear fusion in the Sun's core causes the release of tremendous amounts of energy that leads to very high temperatures and pressure which is much hotter and higher than the temperature and pressure at the exterior surface of the Sun causing the particles in the inner core region to push outwards towards the Sun's surface
Explanation:
Which statement or question is a good hypothesis
Rick works off commission. He earns 10 percent of all manufacturing equipment he sells. if he made a sale of $9,000 how much was his commission
Answer:
$900
Explanation:
Step 1: Our output value is 9000.
Step 2: We represent the unknown value with x.
Step 3: From step 1 above,$9000=100\%$
Step 4: Similarly, x=10%
Step 5: This results in a pair of simple equations:
$9000=100
Step 6: By dividing equation 1 by equation 2 and noting that both the RHS (right hand side) of both
equations have the same unit (%); we have
\frac{9000}{x}=\frac{100\%}{10\%}
Step 7: Again, the reciprocal of both sides gives
\frac{x}{9000}=\frac{10}{100}$
\Rightarrow x=900$
Therefore, $10\%$ of $9000$ is $900$
unknown value with x
step 1 above,$9900=100%
similarly ,x=10%
Mean diameter of cylinder measured by A is 2.50 cm with a possible error of 0.25 cm whereas mean height of cylinder measured by B is 10.0 cm with a possible error of 0.5 cm. Whose measurement is more accurate?
Answer:
The measurement of first cylinder is more accurate.(A)
Explanation:
The least possible error higher will be accuracy.
Two identical metallic sphere having unequal opposite charges are are placed
distance of 0.05m apart in air.
After bringing them in contact
with each other, they are again placed at the same distance apart, now the force of repulsion between them is 0.108 N. Calculate the final charge on each of them.
Answer:
Let the initial charges be q1 and q2 respectively.
After they come in contact, the charges are rearranged such that they acquire same charge.
let us say that charge on each of them is Q.
They are again brought apart at a distance of 0.9 m. Hence, the force between them will be given as
F = kQ2 / r2
0.025 = (9×109 x Q2) / 0.92
Q2 = 0.025 x 0.92 / 9×109
Q = 1.5 x 10-6 C
Explanation:
hey buddy, ❤can u plz subscribe to my UTube channel gtron9528 plz
Let's first consider the dynamics behind the motion in this video. After the student releases the wheel by cutting the cord, what forces are acting on the wheel
Answer:
Hello. You did not provide the video to which the question refers, however, given the context of your question, we can consider that the forces acting on the wheel are the weight of the wheel, the tension that this weight promotes on the rope and the normal force of the axle.
Explanation:
According to the context of the question, we can see that the wheel is being pulled by a rope. The weight of the wheel is the first force that acts on it, promoting resistance to the impulse that the rope promotes on the wheel. When this wheel is pulled by the rope, the weight of the wheel creates tension in the rope, which stretches and becomes tensioned in response to this force. However, this tension is also a force acting on the wheel, as is the normal force on the axis between these two elements.
Help me and I'll make u Brainliest and follow u
26. D. crushing the sugar cube and dissolving it in water.
27. A. atom
28. B. molecule
29. B. plum pudding model of Joseph John Thomson
30. B. He used cathode ray tubes which showed that all atoms contain tiny negatively charged subatomic particles or electrons
31. D. protons and neutrons are relatively heavier than electrons.
What does the sun use for nuclear fusion?
Answer:
The sun uses hydrogen for nuclear fusion.
Answer:
Hydrogen
Explanation:
If 6000 J of heat is added to 200 gm of water at 25° C. What will be its final
temperature?
Answer:
T₂ = 305.17 K
Explanation:
Given that,
Heat, Q = 6000 J
Mass, m = 200 gram
Initial temperature, T₁ = 25° C
We need to find its final temperature. Let it is T₂.
We know that,
[tex]Q=mc\Delta T[/tex]
Where
c is the specific heat of water, c = 4.18 J/g°C
So,
[tex]6000=200\times 4.18\times (T_2-298)\\\\\dfrac{6000}{200\times 4.18}=(T_2-298)\\\\7.17=(T_2-298)\\\\7.17+298=T_2\\\\T_2=305.17\ K[/tex]
So, the final temperature is equal to 305.17 K.
It was found that ice cream sales decrease significantly as the temperature outside decreases; a very strong relationship was found. What is the most likely correlation coefficient from this hypothetical study
Answer:
Value closest to 1
Explanation:
It is described from the scenario above that ice cream sales decreases as the outside temperature increases, hence showing a strong relationship between both variables (icream sales and temperature). The correlation Coefficient is a metric used in regression modeling to depict the strength of relationship between two variables, (The dependent and independent variables). Correlation Coefficient ranges from (-1 to +1). With values close to 1 or - 1. Also the positive and negative signs are used to show the type of relationship between the variables. If an increase in variable A leads to a decrease in variable B, then we have negative correlation (-) ; while an increase or decrease in both variables depicts a positive correlation. The most likely correlation Coefficient for the study above will be a positive value which is close to 1 since the relationship is described as strong.
In uplifting 750 newton load with the help of 2 meter long lever lever took 250 newton efforts . What will be the efficiency of a machine if the fulcrum is kept 50 cm from the load
Answer:
the efficiency of the machine is 100%
Explanation:
Given;
load, L = 750 N
length of the lever, L = 2 m
effort applied, E = 250 N
Position of the load from the fulcrum, = 50 cm
50cm
0↓--------------------------Δ-------------------------------↓---------200 cm
750 N x cm 250 N
Apply the principle of moment;
750(50) = 250(x)
x = (750 x 50) / (250)
x = 150 cm
the distance of the effort = 150 cm = 1.5 m
the distance of the load = 50 cm = 0.5 m
The velocity ratio of the machine = 1.5/0.5
= 3
The mechanical advantage of the machine is calculated as;
M.A = Load/effort
M.A = 750 / 250
M.A = 3
The efficiency of the machine is calculated as;
E = (M.A / V.R) x 100%
E = (3/3) x 100% = 100%
Therefore, the efficiency of the machine is 100%
Calculate the gravitational force between two bodies of masses 10kg and 55kg, if they are placed at a distance of 2m apart.
Answer:
F = 9.177*10^-9N
Explanation:
Gravitational force between the two bodies is expressed as;
F = GMm/r²
Given tha
M = 55kg
m = 10kg
r = 2m
G = 6.67408 × 10-11 m³ kg-1 s-2
Substitute;
F = GMm/r²
F = 6.67408 × 10-11*55*10/2²
F = 3,670.744× 10-11/4
F = 9.177*10^-9N
Which of the following is an example of a surface wave?
A. Compression wave
B. Sound wave
C. Electromagnetic wave
D. Ocean wave
Answer:
ocean wave
hope it helped you
18.How much momentum will a dump-bell of mass 10 kg transfer to the floor if it falls from a height.of 80 cm ? Take its downward acceleration to be 10 m s-2
Such asSuch ToSuch aSuch as طHow do I send the answer to the question?OkI don't know how to use this program
Answer:
MOMENTUM = 40kg ms-¹
hope it helps
have a nice day
To leave the gravitational pull of the Earth, and explore other planets, satellites must have at least:
Answer:
To explore the other planets, the satellite must have the velocity more than the escape velocity.
Explanation:
The minimum velocity required by any object to escape from the earth gravitational pull is called the escape velocity.
The escape velocity for any planet depends on the mass of planet and radius of planet. It does not depends on the mass of object. The escape velocity is same for any mass for a particular planet.
So, to explore the other planets, the satellite must have the velocity more than the escape velocity.
A pair of forces with equal magnitude, opposite directions, and different lines of action is called a "couple." When a couple acts on a rigid object, the couple produces a torque that does not depend on the location of the axis. The drawing shows a couple acting on a tire wrench, each force being perpendicular to the wrench. Determine an expression for the torque produced by the couple when the axis is perpendicular to the tire and passes through the following. Express your answers in terms of the magnitude F of the force and the length L of the wrench.
The drawing shows the couple acting on a tire wrench is missing and so i have attached it.
We are to find an expression for the torque when the axis is perpendicular to the tire and passes through the points A, B & C
Answer:
Point A: τ = Fl
Point B: τ = 0
Point C: - Fl
Explanation:
Formula for torque is;
τ = F × d
Where;
F is perpendicular force
d is distance.
Thus;
> At point A, it means we are taking torque about point A and so we have;
τ = (-F × 0) + (F × L)
τ = Fl
> At point B, it means we are taking torque about point B and so we have;
τ = (-F × L/2) + (F × L/2)
τ = -(FL/2) + (FL/2)
τ = 0
> At point C, it means we are taking torque about point C and so we have;
τ = (-F × L) + (F × 0)
τ = -FL
Physicist Max Planck showed how objects like stars give off different colors based on their temperature. What color are the hottest stars
Answer:
the brightest found are Blue - White with
Explanation:
The energy emission of objects increases with their temperature, specifically Wien described the process in an expression
[tex]\lambda_{maximum}[/tex] T = 2,898 10⁻³
With this expression we can find the temperature of the stars by the color they emit.
Specifically the Sun has a color of 550 nm which corresponds to 5400K
bright stars have a BLUE color corresponding to 7500K
the brightest found are Blue - White with a temperature of 20000K
What do you mean by kinematics?
Explanation:
study of motion of an object ...plzz if anyone knies the correct meaning of it ..do comment
iv. An object is 14 cm in front of a convex mirror. The image is 5.8 cm behind the mirror. What is the focal length of the mirror? A. 4.1cm B. 8.2 cm C. 9.9 cm D. 20 cm
Answer:
C. 9.9 cm
Explanation:
The location of the object, u = 14 cm
The location of the image, v = 5.8 cm
The focal length of the mirror, f = Required
The mirror formula for a convex mirror is given as follows;
[tex]\dfrac{1}{u} -\dfrac{1}{v} = -\dfrac{1}{f}[/tex]
Therefore, we get;
[tex]\dfrac{1}{14 \ cm} -\dfrac{1}{5.8 \ cm} =- \dfrac{41}{406 \ cm} = -\dfrac{1}{f}[/tex]
Therefore;
[tex]f = \dfrac{406 \ cm}{41} \approx 9.9 \ cm[/tex]
The focal length of the mirror, f ≈ 9.9 cm
Which of these would have the greatest pressure?
Group of answer choices
A large balloon with few gas molecules at a high temperature
A small balloon with many gas molecules at a low temperature
A small balloon with many gas molecules at a high temperature
A large balloon with few gas molecules at a low temperature
TRUE OR FALSE. when an object changed direction without changing its speed, it is not accelerating
Answer:
True.
Explanation:
The velocity vector is constant in magnitude but changing in direction. Because the speed is constant for such a motion, many students have the misconception that there is no acceleration. ... But the fact is that an accelerating object is an object that is changing its velocity.
A 0.15-mm-wide slit is illuminated by light of wavelength 462 nm. Consider a point P on a viewing screen on which the diffraction pattern of the slit is viewed; the point is at 26.9° from the central axis of the slit. What is the phase difference between the Huygens' wavelets arriving at P from the top and midpoint of the slit?
Answer:
[tex]\triangle \phi=461.5rad[/tex]
Explanation:
From the question we are told that:
Silt width [tex]w=0.15=>0.1510^{-3}[/tex]
Wavelength [tex]\lambda=462nm=462*10^{-9}[/tex]
Angle [tex]\theta=26.9[/tex]
Generally the equation for Phase difference is mathematically given by
[tex]\triangle \phi=\frac{2 \pi}{\lambda}(\frac{wsin\theta }{2})[/tex]
[tex]\triangle \phi=\frac{2 \pi}{462*10^{-9}}(\frac{0.1510^{-3}*sin 26.9 }{2})[/tex]
[tex]\triangle \phi=461.5rad[/tex]
[tex]\triangle \phi=146.89\pi[/tex]
A piano string of density 0.0050 kg/m is under a tension of 1,350 N. Find the velocity with which a wave travels on the string.
Answer:
519.62 m/s
Explanation:
Applying,
v = √(T/m').............. Equation 1
Where v = velocity of the wave, T = Tension on the string, m' = mass per unit length of the string
From the question,
Given: T = 1350 N, m' = 0.005 kg/m
Substitute these values into equation 1
v = √(1350/0.005)
v = √(270000)
v = 519.62 m/s
explain the role of standard units to bring uniformity in the measurement
Answer:
We need standard unit for measurement to make our judgement more reliable and accurate. For proper dealing, measurement should be same for everybody. Thus there should be uniformity in measurement. For the sake of uniformity we need a common set of units of measurement, which are called standard units.
suppose the pilot starting again from rest opens the throttle part.way at constant acceleration the airboat then covers a distance of 60.0m in 10.0s find the net force action on the boat
Answer:
Acceleration is 1.2 m/s^2.
Explanation:
initial velocity, u = 0
distance, d = 60 m
time, t = 10 s
Let the acceleration is a.
use second equation of motion
[tex]s= u t +0.5 at^2\\\\60 = 0 + 0.5 \times a \times 10\times 10\\\\a = 1.2 m/s^2[/tex]
Now according to the Newton's second law
Force = mass x acceleration
Let the mass is m.
F = m x 1.2 = 1.2 m Newton
Presence of _______- in retina gives us night vision that is help us to see in dim light.Required to answer. Single choice. Immersive Reader (1 Point) cornea retina lens rods
Answer: Rods
Explanation:
The rod cells in the retina are the reason we are able to see at night and in dim light. They exist on the edges of the retina which is why they are also very useful for the peripheral vision of a human.
Rod cells number over 90 million in the eyes and although very useful for seeing in dimmer light, they are not very useful for color vision which is why humans see less colors in the dark.
A uniform meter rule of mass 10g is balanced on a knife edge placed at 45cm mark. Calculate the distance of a mass 25g from the pivot
Answer:
2 cm.
Explanation:
Please see attached photo for diagram.
In the attached photo, y is the distance from the pivot to which the 25 g is placed.
The value of y can be obtained as follow:
Clockwise moment = 5 × 10
Anticlock wise moment = y × 25
Anticlock wise moment = Clockwise moment
y × 25 = 5 × 10
y × 25 = 50
Divide both side by 25
y = 50/25
y = 2 cm
Thus, the distance is 2 cm
Do you believe in aliens? And if so, what's your reasoning for believing in them?
Answer:
I believe in aliens but I do not think everyone should. I started to believe in aliens since the US government said they would be taking extraterrestrial life seriously. They will be in our lives sooner or later, so we shouldn't be ignoring their presence. I believe them because surveys show that nearly half of Americans believe that aliens have visited the Earth, either in the ancient past or recently. That percentage has been increasing. Belief in alien visitation is greater than belief that Bigfoot is a real creature, but less than belief that places can be haunted by spirits. Also there have been a lot of UFO sightings, and a Navy Jet has a video of that as well. These small things is just hard to ignore, and they make me and hopefully others believe in aliens.
3.00 m^3 of water is at 20.0°C.
If you raise its temperature to
60.0°C, by how much will its
volume expand?
Water
ß = 207•10-6C-1
(Unit = m^3)
Answer:
9m^3
Explanation:
Given data
volume v1= 3m^3
volume v2= ???
Temperature T1= 20.0°C.
Temperature T2= 60.0°C.
Applying the relation for temperature and volume
V1/T1= V2/T2
substitute
3/20= V2/60
3*60= V2*20
180= 20*V2
180/20= V2
V2= 9m^3
Hence the final volume is 9m^3
