Answer:
The gauge pressure is [tex]P = 687.4 \ Pa[/tex]
Explanation:
From the question we are told that
The rate of flow is [tex]Q = 0.00027 m^3 /s[/tex]
The height is h = 10 m
The radius is r = 0.01 m
The viscosity is [tex]\eta = 1mPa \cdot s = 1 *10^{-3} \ Pa\cdot s[/tex]
Generally the gauge pressure according to Poiseuille's equation is mathematically represented as
[tex]P = 8 \pi \eta * \frac{L * v }{ A}[/tex]
Here v is the velocity of the water which is mathematically represented according to continuity equation as
[tex]v = \frac{Q}{A }[/tex]
Where A is the cross-sectional area which is mathematically represented as
[tex]A = \pi r^2[/tex]
substituting values
[tex]A = 3.142 *(0.01)^2[/tex]
[tex]A = 3.142 *10^{-4} \ m^2[/tex]
So
[tex]v = \frac{ 0.00027}{3.142*10^{-4}}[/tex]
[tex]v = 0.8593 \ m/s[/tex]
So
[tex]P = 8 * 3.142 * 1.0*10^{-3}* \frac{10 * 0.8593 }{ 3.142*10^{-4}}[/tex]
[tex]P = 687.4 \ Pa[/tex]
A Cannonball is shot at an angle of 35.0 degrees and is in flight for 11.0 seconds before hitting the ground at the same height from which it was shot.
A. What is the magnitude of the inital velocity?B. What was the maximum height reached by the cannonball?C. How far, horizontally, did it travel?
Answer:
Explanation:
According to Equations of Projectile motion :
[tex]Time\ of\ Flight = \frac{2vsin(x)}{g}[/tex]
vsin(x) = 11 * 9.8 / 2 = 53.9 m/sec
(A) v (Initial velocity) = 11 * 9.8 / 2 * sin(35) = 94.56 m/sec
[tex]Maximum Height = \frac{(vsinx)^{2} }{2g}[/tex]
(B) Maximum Height = 53.9 * 53.9 / 2 * 9.8 = 142.2 m
[tex]Horizontal Range = vcosx * t[/tex]
(C) Horizontal Range = 94.56 * 0.81 * 11 = 842.52 m
The equivalent resistance of two resistors connected in series is always greater than the equivalent resistance of the same two resistors connected in parallel. True False
Answer:
True
Explanation:
Because the resistors in series is the sum of the two resistors given as
R= R1+R2
While that of resistors in parallel is the sum of the reciprocal of the resistance given as
1/R = 1/ R1+ 1/R2
So that of series connection will be greater
within which type of system is the total mass conserved but not the total energy
In a closed system the mass is conserved, but the energy is not conserved.
To find the answer, we have to study about different systems in thermodynamics.
What is thermodynamic system?A system, which can be expressed in terms of thermodynamic coordinates is called Thermodynamic system.Open system: System can exchange both energy and matter, thus, both energy and matter is not conserved here.Closed system can exchange energy with its surroundings (as heat or work), but not matter.Isolated system: A system that is open to the environment can interchange energy and matter, but a system that is insulated from it cannot.Thus, we can conclude that, in closed system the mass is conserved, but the energy is not conserved.
Learn more about Thermodynamic system here:
https://brainly.com/question/26035962
#SPJ1
A converging lens 7.50 cm in diameter has a focal length of 330 mm . For related problem-solving tips and strategies, you may want to view a Video Tutor Solution of resolving power of the human eye. Part A If the resolution is diffraction limited, how far away can an object be if points on it transversely 4.10 mm apart are to be resolved (according to Rayleigh's criterion) by means of light of wavelength 600 nm
Answer:
D Is 430m
Explanation:
See attached file
When the magnet falls toward the copper block, the changing flux in the copper creates eddy currents that oppose the change in flux. The resulting braking force between the magnet and the copper block always opposes the motion of the magnet, slowing it as it falls. The braking force on the magnet is nearly equal to its weight, so it falls very slowly. The rate of the fall produces a rate of flux change sufficient to produce a current that provides the braking force. If the magnet is pushed, forcefully, toward the block, the rate of change of flux is much higher than this. When the magnet is moving much more quickly than it will fall unaided, what is the direction of the net force on the magnet?
Answer:
The net force is directed downwards.
Explanation:
Since the magnet is falling much more faster than it would unaided, then there is a net force that is accelerating the magnet downwards. We know that acceleration is due to a force acting on a mass, and in this case, the magnet is the mass. Also, the acceleration is always in the direction of the force producing it, which means that the net force on the magnet is vertically downwards.
A ceiling fan is spinning at 45 revolutions per minute when it is switched to a higher speed. It accelerates uniformly, and 2.0 seconds later it is spinning at 110 revolutions per minute. Through how many radians did it rotate during the transition of speeds
Answer:
θ = 16.2 rad
Explanation:
First we find the angular acceleration by using first equation of motion in angular form:
ωf = ωi + αt
where,
ωf =final angular speed = (110 rev/min)(2π rad/1 rev)(1 min/60 s) = 11.5 rad/s
ωi =initial angular speed = (45 rev/min)(2π rad/1 rev)(1 min/60 s) = 4.7 rad/s
α = angular acceleration = ?
t = time = 2 s
Therefore,
11.5 rad/s = 4.7 rad/s + α(2 s)
α = (6.8 rad/s)/(2 s)
α = 3.4 rad/s²
Now, we use 2nd equation of motion:
θ = ωi t + (1/2)αt²
where,
θ = rotation = ?
Therefore,
θ = (4.7 rad/s)(2 s) + (1/2)(3.4 rad/s²)(2 s)²
θ = 9.4 rad + 6.8 rad
θ = 16.2 rad
if a 1-m diameter sewer pipe is flowing at a depth of 0.4 m and has a flow rate of 0.15 m^3/s, what will be the flow rate when the pipe flows full?
Answer:
0.35 m³/s
Explanation:
When the pipe's depth is 0.4 m, the area of the circular segment is:
A = ½ R² (θ − sin θ)
The depth of the water is:
h = R (1 − cos(θ/2))
Solving for θ:
0.4 = 0.5 (1 − cos(θ/2))
0.8 = 1 − cos(θ/2)
cos(θ/2) = 0.2
θ/2 = acos(0.2)
θ = 2 acos(0.2)
θ ≈ 2.74 rad
The area is therefore:
A = ½ (0.5 m)² (2.74 − sin 2.74)
A = 0.338 m²
The cross-sectional area when the pipe is full is:
A = π (0.5 m)²
A = 0.785 m²
The flow velocity is constant:
v = v
Q / A = Q / A
(0.15 m³/s) / (0.338 m²) = Q / (0.785 m²)
Q = 0.35 m³/s
When a ray of light passes from glass to water it is?
Answer:
[tex]\huge\boxed{Refracted}[/tex]
Explanation:
When a ray of light passes from glass to water, it
1) is Slightly refracted (bending of light)
2) moves away from the normal.
Whenever a light ray travels from a denser medium to a rarer medium, it bends away from the normal.
Answer:
refraction
Explanation:
A person looks horizontally at the edge of a swimming pool. If its length is 5 m, and the pool is filled to the surface, to what depth (in m) could the observer see
Answer:
The observer could see to a depth of 4.38 m
Explanation:
Please check attachment for diagram.
Mathematically, from Snell law;
n1sin theta = n2 sin theta
1 * sin 90 = n2 * sin θR
where n2 = 1.33
1/1.33 = sin θR
Sin θR = 0.7519
θR = arc sin 0.7519
θR = 48.76
Now to get the height, we use the triangle
Using trigonometric ratio;
Tan( 90- θR) = H/5
H = 5 Tan( 90 - θR)
H = 5 Tan( 90-48.76)
H = 5 Tan41.24
H = 4.38 m
Light of wavelength 500 nm falls on two slits spaced 0.2 mm apart. If the spacing between the first and third dark fringes is to be 4.0 mm, what is the distance from the slits to a screen?
Answer:
L = 0.8 m
Explanation:
Since, the distance between first and third dark fringes is 4 mm. Therefore, the fringe spacing between consecutive dark fringes will be:
Δx = 4 mm/2 = 2 mm = 2 x 10⁻³ m
but,
Δx = λL/d
λ = wavelength of the light = 500 nm = 5 x 10⁻⁷ m
d = slit spacing = 0.2 mm = 0.2 x 10⁻³ m
L = Distance between slits and screen = ?
Therefore, using the values, we get:
2 x 10⁻³ m = (5 x 10⁻⁷ m)(L)/(0.2 x 10⁻³)
L = (2 x 10⁻³ m)(0.2 x 10⁻³ m)/(5 x 10⁻⁷ m)
L = 0.8 m
A 500 nm wavelength light illuminates a soap film with an index of refraction 1.33 to make it look bright. If the beam of light is incident normal on the film, what is the minimum thickness of the film
Answer:
t(min) = 94nm
Explanation:
The wavelength of the light incident is 500 nm.
The refractive index of the film is 1.33.
The minimum thickness of the soap film required for constructive interference.
The thickness of the film for the constructive interference is given by:
2*t= (m + 1/2) λ′
Now, λ′ = λ/μ = 500/1.33 = 376nm
The minimum thickness of the film
′t′ will be at m=0 :
2*t(min) = (0 + 1/2) 376
t(min) = 94nm
A cylinder with rotational inertia I1=2.0kg·m2 rotates clockwise about a vertical axis through its center with angular speed ω1=5.0rad/s. A second cylinder with rotational inertia I2=1.0kg·m2 rotates counterclockwise about the same axis with angular speed ω2=8.0rad/s. If the cylinders couple so they have the same rotational axis what is the angular speed of the combination? What percentage of the original kinetic energy is lost to friction?
Answer:
a) 0.67 rad/sec in the clockwise direction.
b) 98.8% of the kinetic energy is lost.
Explanation:
Let us take clockwise angular speed as +ve
For first cylinder
rotational inertia [tex]I[/tex] = 2.0 kg-m^2
angular speed ω = +5.0 rad/s
For second cylinder
rotational inertia [tex]I[/tex] = 1.0 kg-m^2
angular speed = -8.0 rad/s
The rotational momentum of a rotating body is given as = [tex]I[/tex]ω
where [tex]I[/tex] is the rotational inertia
ω is the angular speed
The rotational momenta of the cylinders are:
for first cylinder = [tex]I[/tex]ω = 2.0 x 5.0 = 10 kg-m^2 rad/s
for second cylinder = [tex]I[/tex]ω = 1.0 x (-8.0) = -8 kg-m^2 rad/s
The total initial angular momentum of this system cylinders before they were coupled together = 10 + (-8) = 2 kg-m^2 rad/s
When they are coupled coupled together, their total rotational inertia [tex]I_{t}[/tex] = 1.0 + 2.0 = 3 kg-m^2
Their final angular rotational momentum after coupling = [tex]I_{t}[/tex][tex]w_{f}[/tex]
where [tex]I_{t}[/tex] is their total rotational inertia
[tex]w_{f}[/tex] = their final angular speed together
Final angular momentum = 3 x [tex]w_{f}[/tex] = 3[tex]w_{f}[/tex]
According to the conservation of angular momentum, the initial rotational momentum must be equal to the final rotational momentum
this means that
2 = 3[tex]w_{f}[/tex]
[tex]w_{f}[/tex] = final total angular speed of the coupled cylinders = 2/3 = 0.67 rad/s
From the first statement, the direction is clockwise
b) Rotational kinetic energy = [tex]\frac{1}{2} Iw^{2}[/tex]
where [tex]I[/tex] is the rotational inertia
[tex]w[/tex] is the angular speed
The kinetic energy of the cylinders are:
for first cylinder = [tex]\frac{1}{2} Iw^{2}[/tex] = [tex]\frac{1}{2}*2*5^{2}[/tex] = 25 J
for second cylinder = [tex]\frac{1}{2}*1*8^{2}[/tex] = 32 J
Total initial energy of the system = 25 + 32 = 57 J
The final kinetic energy of the cylinders after coupling = [tex]\frac{1}{2}I_{t}w^{2} _{f}[/tex]
where
where [tex]I_{t}[/tex] is the total rotational inertia of the cylinders
[tex]w_{f}[/tex] is final total angular speed of the coupled cylinders
Final kinetic energy = [tex]\frac{1}{2}*3*0.67^{2}[/tex] = 0.67 J
kinetic energy lost = 57 - 0.67 = 56.33 J
percentage = 56.33/57 x 100% = 98.8%
A) The angular speed of the combination of the two cylinders is; ω₃ = 0.67 rad/s
B) The percentage of the original kinetic energy lost to friction is;
percentage energy lost = 98.82%
We are given;
Rotational Inertia for first cylinder; I₁ = 2 kg.m²
Angular speed of first cylinder; ω₁ = 5 rad/s
Angular speed of second cylinder; ω₂ = 8 rad/s
Rotational Inertia for second cylinder; I₂ = 1 kg.m²
From conservation of angular momentum, we know that;
Initial angular Momentum([tex]L_{i}[/tex]) = Final angular Momentum([tex]L_{f}[/tex])
Thus;
I₁ω₁ + I₂ω₂ = I₃ω₃
Where;
ω₃ is the angular speed when the two cylinders are combined
I₃ = I₁ + I₂
I₃ = 2 + 1
I₃ = 3 kg.m²
Since the second cylinder rotates in an anticlockwise direction, then its' angular speed will be negative. Thus;
(2 * 5) + (1 * -8) = 3ω₃
10 - 8 = 3ω₃
3ω₃ = 2
ω₃ = 2/3
ω₃ = 0.67 rad/s
B) Let us find initial kinetic energy;
E_i = ¹/₂I₁ω₁² + ¹/₂I₂ω₂²
E_i = ¹/₂((2 * 5²) + (1 * 8²)
E_i = 57 J
Final kinetic energy is;
E_f = ¹/₂I₃ω₃²
E_f = ¹/₂ * 3 * 0.67²
E_f = 0.67335 J
Energy lost = 57 - 0.67335 = 56.32665 J
percentage energy lost = (56.32665/57) * 100%
percentage energy lost = 98.82%
Read more at; https://brainly.com/question/14121636
A high school physics student claims her muscle car can achieve a constant acceleration of 10 ft/s/s. Her friend develops an accelerometer to confirm the feat. The accelerometer consists of a 1 ft long rod (mass=4 kg) with one end attached to the ceiling of the car, but free to rotate. During acceleration, the rod rotates. What will be the angle of rotation of the rod during this acceleration? Assume the road is flat and straight.
Answer: Ф = 17.2657 ≈ 17°
Explanation:
we simply apply ET =0 about the ending of the rod
so In.g.L/2sinФ - In.a.L/2cosФ = 0
g.sinФ - a.cosФ = 0
g.sinФ = a.cosФ
∴ tanФ = a/g
Ф = tan⁻¹ a / g
Ф = tan⁻¹ ( 10 / 32.17405)
Ф = tan⁻¹ 0.31080948777
Ф = 17.2657 ≈ 17°
Therefore the angle of rotation of the rod during this acceleration is 17.2657 ≈ 17°
Nine tree lights are connected inparallel across 120-V potential difference. The cord to the wall socket carries a current of 0.43 A. Required:a. Detrmine the resistance of one of the bulbs.b. What would the current be if the bulbs were connected in series?
Answer:
a)3000ohm
b)4.44mA
Explanation:
a) we were given a Nine tree lights connected inparallel across 120-V potential difference, since the resistor are in parallel we use the expresion below
1/R(total)= 1/R₁ + 1/R₂ + 1/R₃ + 1/R₃ +.... 1/R₉
But according to ohm'law which can be expressed below
V=IR
R=V/I
R(total)= 120/0.36
= 333.33ohm
1/R(total)= 1/R₁ + 1/R₂ + 1/R₃ + 1/R₃ +.... 1/R₉
R₁=R₂ =R₃ =R₄= R₅=R₆=R₇=R₈=R₉
1/R(total)=9/R
1/333.33= 9/R
R= 3000ohm
Therefore, the resistance is 3000ohm
b)the bulbs were connected in series here, then for series connection we use below expression
R₁=R₂ =R₃ =R₄= R₅=R₆=R₇=R₈=R₉
R(total)=9R
= 9*3000
=27000ohm
I=VR
I=V/R
I= 120/27000
= 4.44*10⁻³A
4.44mA
Therefore, the current is 4.4mA
What is the maximum speed (in units of m/s) with which a car can round a
flat horizontal curve of radius (r=60 m), if the coefficient of static friction between tires and
road is (0.4)?
A) 5
B) 15.5
€) 240
D) 25.1
Answer:
B) 15.5 m/s
Explanation:
r = 60m
μs = 0.4
using the formula max V = √r*g*μs (flat roadway)
v = sqrt(60 * 10 * 0.4)
v = 15.5 m/s
What would happen in a State if its citizens lack relevant knowledge, skills
and positive attitude?
Answer:
If the older generation is lacking, the younger generation would likely have knowledge, skill, or a positive attitude in some combination, but it is relative to the culture.
The simple reason is the desirability for genetic variation using recessive genes.
In other words, if the older generation lacks something, it tends to be something they don’t need, but something that will look good on young people. But mostly relative to the culture and education system.
Hope this helps
A chemist must dilute 55.6 ml of 1.48 M aqueous silver nitrate (AgNO3)solution until the concentration falls to 1.00 M. He'll do this by adding distilled water to the solution until it reaches a certain final volume. Calculate this final volume, in milliliters. Round your answer to 3 significant digits.
Answer:
82.2 mL
Explanation:
The process of adding water to a solution to make it more dilute is known as dilution. The formula for dilution is;
C1V1=C2V2
Where;
C1= concentration of stock solution
V1= volume of stock solution
C2= concentration of dilute solution
V2= volume of dilute solution
V2= C1V1/C2
V2= 1.48 × 55.6/ 1.0
V2= 82.2 mL
Two hoops, staring from rest, roll down identical incline planes. The work done by nonconservative forces is zero. The hoops have the same mass, but the larger hoop has twice the radius. Which hoop will have the greater total kinetic energy at the bottom
Answer:
They both have the same total K.E at the bottom
Explanation:
This Is because If assuming no work is done by non conservative forces, total mechanical energy must be conserved
So
K1 + U1 = K2 + U2
But If both hoops start from rest, and and at the bottom of the incline the level for gravitational potential energy is zero for reference
thus
K1 = 0 , U2 = 0
ΔK = ΔU = m g. h
But if the two inclines have the same height, and both hoops have the same mass m,
So difference in kinetic energy, must be the same for both hoops.
Sunlight reflected from a smooth ice surface is completely polarized. Determine the angle of incidence. (nice = 1.31.)
Answer:
Explanation:
We shall apply Brewster's law to solve the problem . Let i be the angle of reflection required. According to this law ,
tan i = μ where i is angle of incidence , μ is refractive index of the medium .
Here i = ? , μ = 1.31
tani = 1.31
i = 53° approx .
At the angle of 53° incidence , the reflected ray will be completely polarised .
A satellite in geostationary orbit is used to transmit data via electromagnetic radiation. The satellite is at a height of 35,000 km above the surface of the earth, and we assume it has an isotropic power output of 1.0 kW (although, in practice, satellite antennas transmit signals that are less powerful but more directional).
Required:
a. Reception devices pick up the variation in the electric field vector of the electromagnetic wave sent out by the satellite. Given the satellite specifications listed in the problem introduction, what is the amplitude E0 of the electric field vector of the satellite broadcast as measured at the surface of the earth? Use ϵ0=8.85×10^−12C/(V⋅m) for the permittivity of space and c=3.00×10^8m/s for the speed of light.
b. Imagine that the satellite described in the problem introduction is used to transmit television signals. You have a satellite TV reciever consisting of a circular dish of radius R which focuses the electromagnetic energy incident from the satellite onto a receiver which has a surface area of 5 cm^2. How large does the radius R of the dish have to be to achieve an electric field vector amplitude of 0.1 mV/m at the receiver?
Answer:
1. 6.99x 10^-6V/m
2. 18m
Explanation:
See attached file
An electron moves on a circular orbit in a uniform magnetic field of 7.83×10-4 T. The kinetic energy of the electron is 55.3 eV. What is the diameter of the orbit?
Answer:
3.9E-8
Explanation:
We know that
Mv²/r = Bqv
So
r= mv/Bq
But E is 1/2mv² which is 5.53eV
m²v² =2m x 5.53eV
mv = √( 2 x 9.1E-31)
So
r= √( 2 x9.1E-31 x 5.53)/ 7.83x10^-4 x1.6E-19
= 3.9x10-8cm
Explanation:
Calculate the range of wavelengths (in m) for AM radio given its frequency range is 540 to 1,600 kHz. smaller value m larger value m (b) Do the same for the ultraviolet frequency range of 760 to 30,000 THz. smaller value m larger value m
Answer:
a) λ = 555.5 m, λ = 187.5 nm
Explanation:
The velocity of a wave is given by the relation
c = λ f
λ = c /f
a) length of the radii AM
λ = 3 10⁸/540 10⁻⁷
λ= 5.555 102 m
λ = 555.5 m
f = 1600 kHz
λ = 3 108/1600 103
λ = 1.875 102 m
lam = 187.5 nm
b) light = 760 Thz = 760 10-12 Hz
λ= c/f
λ = 3 108/760 10-12
λ = 3.947 10-9
λ= 30000 Thz
λ= c/f
λ = 3 10⁸/ 30000 10-12
λ = 1 m
A resistor and a capacitor are connected in series to an ideal battery of constant terminal voltage. At the moment contact is made with the battery, the voltage across the resistor is
Answer:
At the moment contact is made with the battery, the voltage across the resistor is equal to the batteries terminal voltage
Explanation;
Because at series connection the battery and resistor have equal voltage
"How many wavelengths wide must a single slit be if, at a point 8o from the central maximum, there is a 72 rad phase difference between the top and bottom rays?"
Answer
82.3 wavelengths
An expensive vacuum system can achieve a pressure as low as 1.53 ✕ 10−7 N/m2 at 26°C. How many atoms are there in a cubic centimeter at this pressure and temperature?
Answer:
The value is [tex]N = 3.708*10^{7} \ \ atoms[/tex]
Explanation:
From the question we are told that
The pressure is [tex]P = 1.53 *10^{-7} \ N/m^2[/tex]
The temperature is [tex]T = 26 + 273 = 299 \ K[/tex]
The volume is 1 cubic cm = [tex]1 * 10^{-6} m^3[/tex]
Generally according to the ideal gas law we have that
[tex]PV = NkT[/tex]
here k is the Boltzmann constant with a value [tex]k = 1.38 *10^{-23} \ J/K[/tex]
=> [tex]N = \frac{PV}{ k T}[/tex]
=> [tex]N = \frac{ 1.53 *10^{-7} * (1* 10^{-6})}{ 1.38*10^{-23} * 299}[/tex]
=> [tex]N = 3.708*10^{7} \ \ atoms[/tex]
A jetboat is drifting with a speed of 5.0\,\dfrac{\text m}{\text s}5.0 s m 5, point, 0, start fraction, start text, m, end text, divided by, start text, s, end text, end fraction to the right when the driver turns on the motor. The boat speeds up for 6.0\,\text s6.0s6, point, 0, start text, s, end text with an acceleration of 4.0\,\dfrac{\text m}{\text s^2}4.0 s 2 m 4, point, 0, start fraction, start text, m, end text, divided by, start text, s, end text, squared, end fraction leftward.
The question is incomplete. Here is the entire question.
A jetboat is drifting with a speed of 5.0m/s when the driver turns on the motor. The motor runs for 6.0s causing a constant leftward acceleration of magnitude 4.0m/s². What is the displacement of the boat over the 6.0 seconds time interval?
Answer: Δx = - 42m
Explanation: The jetboat is moving with an acceleration during the time interval, so it is a linear motion with constant acceleration.
For this "type" of motion, displacement (Δx) can be determined by:
[tex]\Delta x = v_{i}.t + \frac{a}{2}.t^{2}[/tex]
[tex]v_{i}[/tex] is the initial velocity
a is acceleration and can be positive or negative, according to the referential.
For Referential, let's assume rightward is positive.
Calculating displacement:
[tex]\Delta x = 5(6) - \frac{4}{2}.6^{2}[/tex]
[tex]\Delta x = 30 - 2.36[/tex]
[tex]\Delta x[/tex] = - 42
Displacement of the boat for t=6.0s interval is [tex]\Delta x[/tex] = - 42m, i.e., 42 m to the left.
This problem explores the behavior of charge on conductors. We take as an example a long conducting rod suspended by insulating strings. Assume that the rod is initially electrically neutral. For convenience we will refer to the left end of the rod as end A, and the right end of the rod as end B. In the answer options for this problem, "strongly attracted/repelled" means "attracted/repelled with a force of magnitude similar to that which would exist between two charged balls.A. A small metal ball is given a negative charge, then brought near (i.e., within about 1/10 the length of the rod) to end A of the rod. What happens to end A of the rod when the ball approaches it closely this first time?
What happens to end A of the rod when the ball approaches it closely this first time?a. It is strongly repelled.b. It is strongly attracted.c. It is weakly attracted.d. It is weakly repelled.e. It is neither attracted nor repelled.
Answer:
e. It is neither attracted nor repelled.
Explanation:
Electrostatic attraction or repulsion occurs between two or more charged particles or conductors. In this case, if the negatively charged ball is brought close to the neutral end A of the rod, there would be no attraction or repulsion between the rod end A and the negatively charged ball. This is because a charged particle or conductor has no attraction or repulsion to a neutral particle or conductor.
Find the average magnitude of the induced emf if the change in shape occurs in 0.125 ss and the local 0.504-TT magnetic field is perpendicular to the plane of the loop.
Complete Question
An emf is induced in a conducting loop of wire 1.12m long as its shape is.
changed from square to circular. Find the average magnitude of the induced emf if the change in shape occurs in 0.125 ss and the local 0.504-TT magnetic field is perpendicular to the plane of the loop.
Answer:
The induced emf is [tex]\epsilon = 0.0863 \ V[/tex]
Explanation:
From the question we are told that
The time taken is [tex]\Delta t = 0.125 \ s[/tex]
The magnitude of the magnetic field is B = 0.504 T
The length of the loop wire is [tex]l = 1.12 \ m[/tex]
Generally the circumference of the wire when in circular form is
[tex]C = 2 \pi r[/tex]
=> [tex]l = 2 \pi r[/tex]
=> [tex]r =[/tex][tex]\frac{l}{2 \pi}[/tex]
=> [tex]r =[/tex][tex]\frac{1.12}{2 * 3.142}[/tex]
=> [tex]r =[/tex][tex]0.1782 \ m[/tex]
Now the area of the wire as a circle is
[tex]A = \pi r^2[/tex]
=> [tex]A = 3.142 * (0.1782)^2[/tex]
=> [tex]A = 0.0998 \ m^2[/tex]
The length of one side of the square is
[tex]b = \frac{l}{4}[/tex]
[tex]b = \frac{1.12}{4}[/tex]
[tex]b = 0.28 \ m[/tex]
Now the area of the wire as a square is
[tex]A_s = b^2[/tex]
=> [tex]A_s =(0.28 )^2[/tex]
[tex]A_s = 0.0784 \ m^2[/tex]
Generally the induced emf is mathematically represented as
[tex]\epsilon = \frac{B * [A - A_s ]}{\Delta t }[/tex]
=> [tex]\epsilon = \frac{0.504 * [0.0998 - 0.0784 ]}{0.125 }[/tex]
=> [tex]\epsilon = 0.0863 \ V[/tex]
A diver shines an underwater searchlight at the surface of a pond (n = 1.33). At what angle (relative to the surface) will the light be totally reflected?
Answer:
41.2°
Explanation:
Total internal reflection is the reflection of the incident ray at the interface between two media in which one of the media has a lower refractive index than the other. It occurs when the angle of incidence in the denser medium exceeds the critical angle.
The critical angle is the angle of incidence in the denser medium when the angle of incidence in the less dense medium is 90°.
Since
n= 1/sin C
C= sin^-(1/n)
C= sin^-(1/1.33)
C= 48.8°
Hence angle of incidence= 90-48.8 = 41.2°
Describe how, using a positively-charged rod and two neutral metal spheres, we canmake one sphere positive without touching it to the rod. You might want to draw adiagram to help you.
Answer:
se the principle of induction.
place the two metallic spheres together, now we bring the positively charged bar closer to the first sphere.
The charge that was induced in the sphere is distributed as infirm as possible,
At this time I separate the spheres and move the bar away, by separating the spheres the excess positive
Explanation:
For this exercise we will use that the electric charge is not created, it is not destroyed and charges of the same sign repel.
Let's use the principle of induction. We place the two metallic spheres together, one in front of the other, now we bring the positively charged bar closer to the first sphere.
Here the positive charge of the bar repels the positive charge of the sphere, but as this is mocil it moves as far away as possible, until the negative charge that remains neutralizes the positive charge of the bar.
The charge that was induced in the sphere is distributed as infirm as possible, most of it in the furthest sphere, since the Coulomb force decreases.
At this time I separate the spheres and move the bar away, by separating the spheres the excess positive charge in the last sphere cannot be neutralized, therefore this sphere remains with a positive charge.
