what is newtons 2nd law​

Answers

Answer 1

According to the Newton's second law :- The acceleration of an object is directly related to the net force and inversely related to its mass. Acceleration of an object depends on two things, force and mass.


Related Questions

What happens if you move a magnet near a coil of wire?
A) current is induced
B)power is consumed
C)the coil becomes magnetized
D) the magnets field is reduced

Answers

The current is induced

You are using a constant force to speed up a toy car from an initial speed of 6.5 m/s
to a final speed of 22.9 m/s. If the toy car has a mass of 340 g, what is the work
needed to speed this car up?

Answers

By the work-energy theorem, the total work done on the car is equal to the change in its kinetic energy:

W = ∆K

W = 1/2 (0.34 kg) (22.9 m/s)² - 1/2 (0.34 kg) (6.5 m/s)²

W82 J

A plane has a mass of 360,000 kg takes-off at a speed of 300 km/hr. i) What should be the minimum acceleration to take off if the length of the runway is 2.00 km.ii) At this acceleration, how much time would the plane need from starting to takeoff. iii) What force must the engines exert to attain this acceleration

Answers

Answer:

i) the minimum acceleration to take off is 22500 km/h²

ii) the required time needed by the plane from starting to takeoff is 0.0133 hrs

iii) required force that the engine must exert to attain acceleration is 625 kN

Explanation:

Given the data in the question;

mass of plane m = 360,000 kg

take of speed v = 300 km/hr = 83.33 m/s

i)

What should be the minimum acceleration to take off if the length of the runway is 2.00 km

from Newton's equation of motion;

v² = u² + 2as

we know that a plane starts from rest, so; u = 0

given that distance S = 2 km

we substitute

(300)² = 0² + ( 2 × a × 2 )

90000 = 4 × a

a = 90000 / 4

a = 22500 km/h²

Therefore,  the minimum acceleration to take off is 22500 km/h²

ii) At this acceleration, how much time would the plane need from starting to takeoff.

from Newton's equation of motion;

v = u + at

we substitute

300 = 0 + 22500 × t

t = 300 / 22500

t = 0.0133 hrs

Therefore, the required time needed by the plane from starting to takeoff is 0.0133 hrs

iii) What force must the engines exert to attain this acceleration

we know that;

F = ma

acceleration a = 22500 km/hr² = 1.736 m/s²

so we substitute

F = 360,000 kg × 1.736 m/s²

F =  624960 N

F = 625 kN

Therefore, required force that the engine must exert to attain acceleration is 625 kN

The two most prominent wavelengths in the light emitted by a hydrogen discharge lamp are 656 nm (red) and 486 nm (blue). Light from a hydrogen lamp illuminates a diffraction grating with 550 lines/mm , and the light is observed on a screen 1.7 m behind the grating.
What is the distance between the first-order red and blue fringes?
Express your answer to two significant figures and include the appropriate units.

Answers

Answer:

Δd = 7.22 10⁻² m

Explanation:

For this exercise we must use the dispersion relationship of a diffraction grating

           d sin θ = m λ

let's use trigonometry

           tan θ = y / L

     

how the angles are small

           tant θ = sinθ  /cos θ = sin θ

we substitute  

           sin θ = y / L

          d y / L = m λ

          y = m λ L / d

let's use direct ruler rule to find the distance between two slits

           

If there are 500 lines in 1 me, what distance is there between two lines

         d = 2/500

        d = 0.004 me = 4 10⁻⁶ m

diffraction gratings are built so that most of the energy is in the first order of diffraction m = 1

let's calculate for each wavelength

λ = 656 nm = 656 10⁻⁹ m

         d₁ = 1 656 10⁻⁹ 1.7 / 4 10⁻⁶

         d₁ = 2.788 10⁻¹ m

λ = 486 nm = 486 10⁻⁹ m

         d₂ = 1 486 10⁻⁹ 1.7 / 4 10⁻⁶

         d₂ = 2.066 10⁻¹ m

the distance between the two lines is

         Δd = d1 -d2

         Δd = (2,788 - 2,066) 10⁻¹

         Δd = 7.22 10⁻² m

Water with a volume flow rate of 0.001 m3/s, flows inside a horizontal pipe with diameter of 1.2 m. If the pipe length is 10m and we assume fully developed internal flow, find the pressure drop across this pipe length.

Answers

Answer:

[tex]\triangle P=1.95*10^{-4}[/tex]

Explanation:

Mass [tex]m=0.001[/tex]

Diameter [tex]d=1.2m[/tex]

Length [tex]l=10m[/tex]

Generally the equation for Volume flow rate is mathematically given by

 [tex]Q=AV[/tex]

 [tex]V=\frac{Q}{\pi/4D^2}[/tex]

 [tex]V=\frac{0.001}{\pi/4(1.2)^2}[/tex]

 [tex]V=8.84*10^{-4}[/tex]

Generally the equation for Friction factor is mathematically given by

 [tex]F=\frac{64}{Re}[/tex]

Where Re

Re=Reynolds Number

 [tex]Re=\frac{pVD}{\mu}[/tex]

 [tex]Re=\frac{1000*8.84*10^{-4}*1.2}{1.002*10^{-3}}[/tex]

 [tex]Re=1040[/tex]

Therefore

 [tex]F=\frac{64}{Re}[/tex]

 [tex]F=\frac{64}{1040}[/tex]

 [tex]F=0.06[/tex]

Generally the equation for Friction factor is mathematically given by

 [tex]Head loss=\frac{fLv^2}{2dg}[/tex]

 [tex]H=\frac{0.06*10*(8.9*10^-4)^2}{2*1.2*9.81}[/tex]

 [tex]H=19.9*10^{-9}[/tex]

Where

[tex]H=\frac{\triangle P}{\rho g}[/tex]

[tex]\triangle P=\frac{19.9*10^{-9}}{10^3*(9.81)}[/tex]

[tex]\triangle P=H*\rho g[/tex]

[tex]\triangle P=1.95*10^{-4}[/tex]

 

The tub of a washer goes into its spin-dry cycle, starting from rest and reaching an angular speed of 3.0 rev/s in 13.0 s. At this point, the person doing the laundry opens the lid, and a safety switch turns off the washer. The tub slows to rest in 12.0 s. Through how many revolutions does the tub turn during this 25 s interval

Answers

Answer:

The tub turns 37.520 revolutions during the 25-second interval.

Explanation:

The total number of revolutions done by the tub of the washer ([tex]\Delta n[/tex]), in revolutions, is the sum of the number of revolutions done in the acceleration ([tex]\Delta n_{1}[/tex]), in revolutions, and deceleration stages ([tex]\Delta n_{2}[/tex]), in revolutions:

[tex]\Delta n = \Delta n_{1} + \Delta n_{2}[/tex] (1)

Then, we expand the previous expression by kinematic equations for uniform accelerated motion:

[tex]\Delta n = \frac{1}{2}\cdot ( \ddot n_{1}\cdot t_{1}^{2} - \ddot n_{2} \cdot t_{2}^{2})[/tex] (1b)

Where:

[tex]\ddot n_{1}, \ddot n_{2}[/tex] - Angular accelerations for acceleration and deceleration stages, in revolutions per square second.

[tex]t_{1}, t_{2}[/tex] - Acceleration and deceleration times, in seconds.

And each acceleration is determined by the following formulas:

Acceleration

[tex]\ddot n_{1} = \frac{\dot n}{t_{1}}[/tex] (2)

Deceleration

[tex]\ddot n_{2} = -\frac{\dot n}{t_{2} }[/tex] (3)

Where [tex]\dot n[/tex] is the maximum angular velocity of the tub of the washer, in revolutions per second.

If we know that [tex]\dot n = 3\,\frac{rev}{s}[/tex], [tex]t_{1} = 13\,s[/tex] and [tex]t_{2} = 12\,s[/tex], then the quantity of revolutions done by the tub is:

[tex]\ddot n_{1} = \frac{3\,\frac{rev}{s} }{13\,s}[/tex]

[tex]\ddot n_{1} = 0.231\,\frac{rev}{s^{2}}[/tex]

[tex]\ddot n_{2} = -\frac{3\,\frac{rev}{s} }{12\,s}[/tex]

[tex]\ddot n_{2} = -0.25\,\frac{rev}{s^{2}}[/tex]

[tex]\Delta n = \frac{1}{2}\cdot ( \ddot n_{1}\cdot t_{1}^{2} + \ddot n_{2} \cdot t_{2}^{2})[/tex]

[tex]\Delta n = \frac{1}{2}\cdot \left[\left(0.231\,\frac{rev}{s^{2}} \right)\cdot (13\,s)^{2}-\left(-0.25\,\frac{rev}{s^{2}} \right)\cdot (12\,s)^{2}\right][/tex]

[tex]\Delta n = 37.520\,rev[/tex]

The tub turns 37.520 revolutions during the 25-second interval.

A horizontal, uniform board of weight 125 N and length 4 m is supported by vertical chains at each end. A person weighing 500 N is sitting on the board. The tension in the right chain is 250 N. How far from the left end of the board is the person sitting

Answers

Answer:

the person  is sitting 1.5 m from the left end of the board

Explanation:

Given the data in the question;

Wb = 125 N

Wm = 500 N

T₂ = 250 N

Now, we know that;

T₁ + T₂ = Wb + Wm

T₁ + 250 = 125 + 500

T₁ = 125 + 500 - 250

T₁ = 375 N

so tension of the left chain is 375 N.

Now, taking torque about the left end

500 × d + 125 × 2 = 250 × 4

500d + 250 = 1000

500d = 1000 - 250

500d = 750

d = 750 / 500

d = 1.5 m

Therefore, the person  is sitting 1.5 m from the left end of the board.

From 2 King 6:1-6, one of the disciples of Elisha was cutting a tree and the ax head fell into the water. While we do not know how high the ax head was when it fell into the water, we will work through a physics example of the ax head's vertical motion as if it were dropped into the water. ( Due date 09/07)
Write your name and date. The due date of this assignment is the height the ax head falls from in meters into the water. For example, if the due date is July 15, then the ax head fell 15 meters to the water.
Write Newton’s 2nd Law in Equation Form.
Write the quantity and units of average gravitational acceleration on the surface of Earth.
Given the ax head mentioned in the opening portion with the height being equal in numerical value of the due day of this assignment. How long does it take for the ax to fall to the river surface?
Compute the final speed of the ax when it hits the water.

Answers

Answer:

time of fall is 1.75 s and the velocity with which it strikes the water is 17.15 m/s.

Explanation:

Height, h =  15 m

Newton's second law

Force = mass x acceleration

The unit of gravitational force is Newton and the value is m x g.

where, m is the mas and g is the acceleration due to gravity.  

Let the time of fall is t.

Use second equation of motion

[tex]s= u t +0.5 at^2\\\\15 = 0 +0.5\times 9.8\times t^{2}\\\\t = 1.75 s[/tex]

Let the final speed is v.

Use third equation of motion

[tex]v^2 = u^2 + 2 a s\\\\v^2 = 0 + 2 \times 9.8\times 15\\\\v =17.15 m/s[/tex]

A hockey puck is sliding across the ice with an initial velocity of 25 m/s. If the coefficient of friction between the hockey puck and the ice is 0.08, how much time (in seconds) will it take before the hockey puck slides to a stop

Answers

Answer: 31.89seconds

Explanation:

Based on the information given, we are meant to calculate deceleration which will be:

t = V/a

where, a = mg

Therefore, t = V/mg

t = 25/0.08 × 9.8

t = 25/0.784

t = 31.89seconds

Therefore, the time that it will take before the hockey puck slides to a stop is 31.89seconds.

As part of a safety investigation, two 1300 kg cars traveling at 17 m/s are crashed into different barriers. Find the average forces exerted on:

a. the car that hits a line of water barrels and takes 1.5 s to stop
b. the car that hits a concrete barrier and takes 0.10 s to stop.

Answers

Answer:

a.  F = 14,733.33 N

b. F = 221,000 N

Explanation:

Given;

mass of the cars, m = 1300 kg

velocity of the cars, v = 17 m/s

time taken for the first car to stop after hitting a barrier, t = 1.5 s

time taken for the second car to stop after hitting a barrier, t = 0.1 s

The average forces exerted on each car is calculated as follows;

a. the car that hits a line of water barrels and takes 1.5 s to stop

[tex]F = ma = m\times \frac{v}{t} = 1300 \times \frac{17}{1.5} = 14,733.33 \ N\\\\F = 14,733.33 \ N[/tex]

b. the car that hits a concrete barrier and takes 0.10 s to stop

[tex]F = ma = m\times \frac{v}{t}= 1300 \times \frac{17}{0.1} = 221,000 \ N\\\\F = 221,000 \ N[/tex]

The equation of damped oscillations is given in the form x=0.05e^-0.25sin½πt (m). Find the velocity of an oscillating point at the moments of time: 0, T, 2T, 3T and 4T.​

Answers

Explanation:

The logarithmic damping decrement of a mathematical pendulum is DeltaT=0.5. How will the amplitude of oscillations decrease during one full oscillation of the pendulum

The triceps muscle in the back of the upper arm extends the forearm. This muscle in a professional boxer exerts a force of 2.00\times 10^32.00×10 ^3 N with an effective perpendicular lever arm of 3.00 cm, producing an angular acceleration of the forearm of 120 rad/s^2 .
What is the moment of inertia of the boxer's forearm?

Answers

Answer:

Explanation:

From the given information:

The torque produced due to the force can be expressed as:

[tex]\tau = F \times r[/tex]

where;

[tex]\tau[/tex] = torque

F = force exerted

r = lever's arm radius

[tex]\tau[/tex] = [tex]2.00 \times 10^3 \times 0.03 m[/tex]

[tex]\tau[/tex] = 60 N.m

However, equating the torque with the moment of inertia & angular acceleration, we use the equation:

[tex]\tau[/tex] = I∝

60 Nm = I × 120 rad/s²

I = 60 Nm/120 rad/s²

I = 0.5 kg.m²

45. Pressure in air undergoes a decrease when the air
a) rises to higher altitudes.
b) accelerates to higher speed.
c) fills a greater space.
d) All of these.

Answers

D okokokokokokok I’m right promise

A rectangular field is of length 42 cm and breadth 25 m. Find the area of the field in SI unit. EXPLAIN STEP BY STEP​

Answers

Answer:

the area of the rectangular field is 10.5 m²

Explanation:

Given;

length of the rectangular field, L = 42 cm = 0.42 m

breadth of the rectangular field, b = 25 m

The area of the rectangular field is calculated as follows;

Area = Length x breadth

Area = 0.42 m x 25 m

Area = 10.5 m²

Therefore, the area of the rectangular field is 10.5 m²

A professional quarterback throws a 0.40 kg football. what is the force of weight?

Answers

Answer:

3.92N

Explanation:

Force= mass×accelerarion due gravity

But mass= 0.40kg

acceleration due to gravity = 9.8 m/s^2

Force = 0.40×9.8

Force=3.92N

Newton's law of cooling states that the rate of change of temperature of an object in a surrounding medium is proportional to the difference of the temperature of the medium and the temperature of the object. Suppose a metal bar, initially at temperature 50 degrees Celsius, is placed in a room which is held at the constant temperature of 40 degrees Celsius. One minute later the bar has cooled to 40.18316 degrees . Write the differential equation that models the temperature in the bar (in degrees Celsius) as a function of time (in minutes). Hint: You will need to find the constant of proportionality. Start by calling the constant k and solving the initial value problem to obtain the temperature as a function of k and t . Then use the observed temperature after one minute to solve for k .

Answers

Answer:

Newton's law of cooling says that the temperature of a body changes at a rate proportional to the difference between its temperature and that of the surrounding medium (the ambient temperature); dT/dt = -K(T - Tₐ) where T = the temperature of the body (°C), t = time (min), k = the proportionality constant (per minute),

Explanation:

Calculate the heat energy conducted per hour through the side walls of a cylindrical steel
boiler of 1.00 m diameter and 3.0 m long if the internal and external temperatures of the
walls are 140 °C and 40 °C respectively and the thickness of the walls is 6.0 mm. (Thermal
conductivity of steel, k = 42 Wm-4°C-4)

Answers

Explanation:

heat caoacity and heat is difference

The heat energy conducted per hour through the side walls of the cylindrical steel boiler  is 27708847 kJ.

What is thermal conductivity?

The rate at which heat is transported by conduction through a material's unit cross-section area when a temperature gradient exits perpendicular to the area is known as thermal conductivity.

In the International System of Units (SI), thermal conductivity is measured by Wm⁻¹K⁻¹.

Diameter of the cylindrical steel boiler: d = 1.00m.

Length  of the cylindrical steel boiler: l = 3.00m.

thickness of the walls is = 6.0 mm = 0.006 m

Temperature gradient is = (140-40) °C/0.006 m = 1666.67 °C/m

Thermal conductivity of steel,  = 42 W/m-°C.

Hence, the heat energy conducted per hour through the side walls of the cylindrical steel boiler = 42×3600×1666.67 ×2π×0.5(0.5+3.0) Joule

= 27708847 kJ

Learn more about  thermal conductivity here:

https://brainly.com/question/23897839

#SPJ2

An electric drill starts from rest and rotates with a constant angular acceleration. After the drill has rotated through a certain angle, the magnitude of the centripetal acceleration of a point on the drill is 8.2 times the magnitude of the tangential acceleration. What is the angle?

Answers

Answer:

The angle is 4.1 rad.

         

Explanation:

The centripetal acceleration (α) is given by:

[tex] \alpha = \omega^{2} r [/tex]    (1)                  

Where:

ω: is the angular velocity  

r: is the radius

And the tangential acceleration (a) is:                      

[tex] a = \alpha r [/tex]      (2)

Since the magnitude of "α" is 8.2 times the magnitude of "a" (equating (2) and (1)) we have:

[tex] \omega^{2} r = 8.2\alpha r   [/tex]

[tex] \omega^{2} = 8.2\alpha [/tex]    (3)      

Now, we can find the angle with the following equation:

[tex] \omega_{f}^{2} = \omega_{0}^{2} + 2\alpha \Delta \theta [/tex]

Where:

[tex] \omega_{f}[/tex]: is the final angular velocity                                                                              [tex] \omega_{0}[/tex]: is the initial angular velocity = 0 (it starts from rest)

[tex]\Delta \theta[/tex]: is the angle

[tex] \omega^{2} = 2\alpha \Delta \theta [/tex]     (4)    

By entering equation (3) into (4) we can calculate the angle:

[tex] 8.2\alpha = 2\alpha \Delta \theta [/tex]

[tex] \Delta \theta = 4.1 rad [/tex]

Therefore, the angle is 4.1 rad.

I hope it helps you!                  

1. Lifting an elevator 18m takes 100kJ. If doing so takes 20s, what is the average power of the elevator during the process?

2. How much work can a 0.4 hp electric mixer do in 15 s?​

Answers

Answer:

1. Power = 5000 Watts

2. Workdone = 11185.5 Joules

Explanation:

Given the following data;

1. Distance = 18 m

Energy = 100 KJ = 100,000 Joules

Time = 20 seconds

To find the average power of the elevator;

Power = energy/time

Power = 100000/20

Power = 5000 Watts

2. Power = 0.4 HP

Time = 15 seconds

Conversion:

1 horsepower = 745.7 Watts

0.4 horsepower = 0.4 * 745.7 = 298.28 Watts

To find the amount of work done by the electric mixer;

Work done = power * time

Workdone = 745.7 * 15

Workdone = 11185.5 Joules

What does it mean when work is positive?
O Velocity is greater than kinetic energy
O Kinetic energy is greater than velocity
The environment did work on an object.
O An object did work on the environment.

Answers

Answer:

d. An object did work on the environment.

Explanation:

Work is defined in many contexts. Some of these are;

i. Work is the product of force and displacement. In this case, work done is positive if the force applied on an object or body and the displacement caused by the force are in the same direction. If instead the force and displacement are in opposite direction, then the work done will be negative. If it is the case the force and the displacement are perpendicular to each other, the work done is zero.

ii. In the first law of thermodynamics, the internal energy of a system is the sum of the work done and the heat exchanged between the system and the environment. Therefore, work done is the difference between the internal energy of a system and the heat exchanged between the system and the environment.

In this case, work is said to be positive if work is done by the system (object) on the environment. It is negative if work is done by the environment on the system (object).

Answer:

its c

Explanation:

An unstretched ideal spring hangs vertically from a fixed support. A 0.4 kg object is then attached to the lower end of the spring. The object is pulled down to a distance of 0.35 m below the unstretched position and released from rest at time t= 0. A graph of the subsequent vertical position y of the lower end of the spring as a function of t is given above, where y= 0 when the spring was initially unstretched. At which time is the upward velocity of the object the greatest?

Answers

Answer:

The correct answer will be "0.25 sec".

Explanation:

The graph of the given question is attached below.

According to the graph of the question,

Time,

T = 1 sec

For the upward velocity,

⇒ [tex]t = \frac{T}{4}[/tex]

By putting the value, we get

⇒    [tex]=\frac{1}{4}[/tex]

⇒    [tex]=0.25 \ sec[/tex]

20 pts.
A man forgets that he set his coffee cup on top of his car. He starts to drive and the coffee CUP rolls off the car onto the road. How does this scenario demonstrate the first law of motion? Be specific and use the words from the law in your answer.​

Answers

Answer:

The cup is acted upon by an unbalanced force which is the acceleration of the car, but before it was an object at rest that stayed at rest.

Explanation:

Newton's first law of motion states, "if a body is at rest or moving at a constant speed in a straight line, it will remain at rest or keep moving in a straight line at constant speed unless it is acted upon by a force."

Since the cup is at rest while sitting on top of the car, it stays at rest as the car begins to move. Since the car is accelerating and the cup is not, the cup falls off of the car.

the two factors that affect the amount of heat​

Answers

Answer:

The two important factors that affect heat energy are specific heat and temperature. Specific heat is a heat-constant of a material per unit mass per degree of temperature change (in units of energy per mass and temperature), like Joules/Kg-°C .

Thank you.....

Have a good day.....

At the start of a basketball game, a referee tosses a basketball straight into the air by giving it some initial speed. After being given that speed, the ball reaches a maximum height of 4.35 m above where it started. Using conservation of energy, find the height of the ball when it has a speed of 2.5 m/s.

Answers

Answer:

0.32 m.

Explanation:

To solve this problem, we must recognise that:

1. At the maximum height, the velocity of the ball is zero.

2. When the velocity of the ball is 2.5 m/s above the ground, it is assumed that the potential energy and kinetic energy of the ball are the same.

With the above information in mind, we shall determine the height of the ball when it has a speed of 2.5 m/s. This can be obtained as follow:

Mass (m) = constant

Acceleration due to gravity (g) = 9.8 m/s²

Velocity (v) = 2.5 m/s

Height (h) =?

PE = KE

Recall:

PE = mgh

KE = ½mv²

Thus,

PE = KE

mgh = ½mv²

Cancel m from both side

gh = ½v²

9.8 × h = ½ × 2.5²

9.8 × h = ½ × 6.25

9.8 × h = 3.125

Divide both side by 9.8

h = 3.125 / 9.8

h = 0.32 m

Thus, the height of the ball when it has a speed of 2.5 m/s is 0.32 m.

In the Biomedical and Physical Sciences building at MSU there are 135 steps from the ground floor to the sixth floor. Each step is 16.6 cm tall. It takes 5 minutes and 30 seconds for a person with a mass of 73.5 kg to walk all the way up. How much work did the person do?

Answers

Answer:

W = 16.4 kJ

Explanation:

Given that,

There are 135 steps from the ground floor to the sixth floor.

Each step is 16.6 cm tall.

The mass of a person, m = 73.5 kg

We need to find the work done by the person. We know that,

Work done = Fd

Where

d is the displacement, d = 135 × 0.166 = 22.41

So,

W = 73.5 × 10 × 22.41

= 16471.35  J

or

W = 16.4 kJ

So, 16.4 kJ is the work done by the person.

Give the number of protons and the number of neutrons in the nucleus of each of the following isotopes Aluminum 25 :13 protons and 12 neutrons

Answers

Answer:

No of proton is 13 and nucleus is 13

The peak value of the electric field component of an electromagnetic wave is E. At a particular instant, the intensity of the wave is of 0.020 W/m2. If the electric field were increased to 5E, what would be the intensity of the wave?

Answers

Answer:

[tex]I_2=0.50 w/m^2[/tex]

Explanation:

From the question we are told that:

initial Intensity [tex]I_1=0.020 w/m^2[/tex]

Final Electric field [tex]E_2=5E[/tex]

Generally the equation for Relation ship between intensity and Electric field is mathematically given by

 [tex]\frac{I_1}{I_2}= \frac{E_1^2}{E_2^2}[/tex]

Therefore

 [tex]I_2=\frac{I_1}{ \frac{E_1^2}{E_2^2}}[/tex]

 [tex]I_2=\frac{0.020}{ \frac{E^2}{5E^2}}[/tex]

 [tex]I_2=0.50 w/m^2[/tex]

A toy car of mass 600g moves through 6m in 2 seconds. The average kinetic energy of the toy car is​

Answers

Answer:

12

Explanation:

I'm a beginner so am not sureeeeee

A crane raises a crate with a mass of 150 kg to a height of 20 m. Given that
the acceleration due to gravity is 9.8 m/s2, what is the crate's potential energy
at this point?

Answers

Answer:

[tex]\boxed {\boxed {\sf 29,400 \ Joules}}[/tex]

Explanation:

Gravitational potential energy is the energy an object possesses due to its position. It is the product of mass, height, and acceleration due to gravity.

[tex]E_P= m \times g \times h[/tex]

The object has a mass of 150 kilograms and is raised to a height of 20 meters. Since this is on Earth, the acceleration due to gravity is 9.8 meters per square second.

m= 150 kg g= 9.8 m/s²h= 20 m

Substitute the values into the formula.

[tex]E_p= 150 \ kg \times 9.8 \ m/s^2 \times 20 \ m[/tex]

Multiply the three numbers and their units together.

[tex]E_p=1470 \ kg*m/s^2 \times 20 m[/tex]

[tex]E_p=29400 \ kg*m^2/s^2[/tex]

Convert the units.

1 kilogram meter square per second squared (1 kg *m²/s²) is equal to 1 Joule (J). Our answer of 29,400 kg*m²/s² is equal to 29,400 Joules.

[tex]E_p= 29,400 \ J[/tex]

The crate has 29,400 Joules of potential energy.

Answer:

29,400 J

Explanation:

did the quiz <3

How can i prove the conservation of mechanical energy?​

Answers

Answer:

We can also prove the conservation of mechanical energy of a freely falling body by the work-energy theorem, which states that change in kinetic energy of a body is equal to work done on it. i.e. W=ΔK. And ΔE=ΔK+ΔU. Hence the mechanical energy of the body is conserved

Explanation:

Other Questions
Solve the equation. 6g = 48 what does g equal? A ramp is in the shape of a triangle alguma army por aqui? ou algum pra conversar? Answer to the question? All of the different organisms interacting in a pond make up:A) a communityB) a populationC) the water cycleD) the habitat The triceps muscle in the back of the upper arm extends the forearm. This muscle in a professional boxer exerts a force of 2.00\times 10^32.0010 ^3 N with an effective perpendicular lever arm of 3.00 cm, producing an angular acceleration of the forearm of 120 rad/s^2 .What is the moment of inertia of the boxer's forearm? Need help with these 2 questions ASAP, no links and a answer with an explanation will get brainly Rocky Mountain Bighorn Sheep live in the mountains. Which behavior is a result of living at high elevations? How much growth or decay is 50(1.05)^t Three consecutive integers have a sum of 30. Which equation can be used to find x, the value of the smallest of the three numbers? (x + 1) + (x + 2) = 30 x + (x + 1) + (x + 2) = 30 x (x + 1) (x + 2) = 30 3 x (x + 1) (x + 2) = 30 David gasta el 20% de su salario en el pago de los servicios bsicos de su casa del resto gasta el 50% en alimentacin si al final se queda con 2000 Crdoba cuanto gana David Pleaseeeee help me!!! Alberto is a lawyer and needs to calculate how much to charge a client for his services. He charges $225 for each hour. He spent 2 1/4 hours consulting with the client, 4 1/2 hours researching the clients case, 3 hours negotiating with the other partys lawyer, and 3 1/2 hours drawing up and filing court papers. How much will he charge? The radius of a circle is 10 cm. Find its circumference in terms of \pi. The skiers glide quickly and easily over the fresh snow.What is the action verb in the sentence? Study the graph showing GDP in the US.A line graph titled G D P Growth in the U S. The x-axis is labeled Year from 2004 to 2014. The y-axis is labeled Percent Growth from negative 4 to 6. 2004 is at 4 percent. 2006 is around 3 percent. 2007 is at 2 percent. 2009 is under negative 2 percent. 2010 is at 2 percent. 2012 is at 2 percent. 2014 is over 2 percent.What conclusion can be drawn about the US economy as a whole between 2006 and 2009?It remained level.It declined steadily.It wavered in growth.It rose from a downturn. What is the best way to use specialized vocabulary in an oral report, so that your listeners still understand you? What did the Freedom Rides that James Farmer Jr. organized in 1961 accomplish?A. They strengthened the reform movement among Southern police officers.B. They drew national attention to continuing segregation with interstate transportation in the SouthC. They stirred up support for segregation among many southern Southern whites.D. They established ethnic studies departments in major American universities. 38 points...texas is ____of new york.-southwest-northwest-northeast-south east The Centers for Disease Control and Prevention Office on Smoking and Health (OSH) is the lead federal agency responsible for comprehensive tobacco prevention and control. OSH was established in 1965 to reduce the death and disease caused by tobacco use and exposure to secondhand smoke. One of the many responsibilities of the OSH is to collect data on tobacco use. The following data show the percentage of U.S. adults who were users of tobacco for a recent 11-year periodYear Percentage of Adults Who Smoke1 22.92 21.73 214 20.35 20.36 19.97 19.48 20.79 20.710 1911 18.8What type of pattern exists in the data?Use simple linear regression analysis to find the parameters for the line that minimizes MSE for this time series. Do not round your interim computations and round your final answers to three decimal places. For subtractive or negative numbers use a minus sign. (Example: -300)y-intercept, b0 =Slope, b1 =MSE =One of OSHs goals is to cut the percentage of U.S. adults who were users of tobacco to 12% or less within nine years of the last year of these data. Does your regression model from part (b) suggest that OSH is on target to meet this goal?Use your model from part (b) to estimate the number of years that must pass after these data have been collected before OSH will achieve this goal. Round your answer to the nearest whole number.years.