Answer:
A
Explanation:
i think a is the answer because if you take an example of group 1 and 2 metals on the periodic table you will notice that they are highly reactive but they have a few electrons in their outer most shells.
I hope this helps
steel wire 8m long and 4mm in diameter is fixed to two rigid b. [1] supports. Calculate the increase in tension when the temperature falls by 10°C. Given linear expansivity of steel, a 12x10 %/K, Young's modulus for steel, Y = 2x10¹¹ N/m².
Answer:
301.6 N
Explanation:
The length of the wire L₀ = 8 m and its diameter, d = 4 mm = 4 × 10⁻³ m. Since its temperature drops by 10°C, it will have a change in length ΔL = L₀αΔθ where α = linear expansivity of steel, a 12 × 10⁻⁶ /K, and Δθ = temperature change = -10°C = -10 K(negative since it is a drop)
So, the strain, ε = ΔL/L₀ = αΔθ = 12 × 10⁻⁶ /K × 10 K = 12 × 10⁻⁵
Now the Young's modulus of steel, Y = σ/ε where σ = stress = T/A where T = increase in tension in steel wire and A = cross-sectional area of wire = πd²/4 where d = diameter of wire = 4 × 10⁻³ m and ε = strain = 12 × 10⁻⁵
So, σ = Yε
Since Y = 2 × 10¹¹ N/m².
Substituting the values of the variables into the equation, we have
σ = Yε
σ = 2 × 10¹¹ N/m² × 12 × 10⁻⁵
σ = 24 × 10⁶ N/m²
Since σ = T/A
T = σA
T = σπd²/4
Substituting the values of the variables into the equation, we have
T = σπd²/4
T = 24 × 10⁶ N/m² × π × (4 × 10⁻³ m)²/4
T = 24 × 10⁶ N/m² × π × 16 × 10⁻⁶ m²/4
T = 24 × 10⁶ N/m² × π × 4 × 10⁻⁶ m²
T = 96 N × π
T = 301.59 N
T ≅ 301.6 N
So, the increase in tension in the steel wire is 301.6 N
if a person buys 10 kg apples in himalayan region and sells in terai region will he get profit or loss. why?
Answer:
he will be in profit
Explanation:
Himalayan region are high above the sea level so the gravity will be less there compared to the Terai region
Terai lies way below he Himalayan region so the pull of gravity will be more compared to Himalayan region
that's why he will be in profit but not loss
The first periodic table of elements Mendeleev created contained only 70 elements. True or false?
Explanation:
FALSE
The first periodic table of elements Mendeleev created contained 63 elements.
Write the dirference between sl system
and cgs system
Explanation:
st system:the internationak system of measurement which i declared form internationäl convention of scientists held in france in 1960AD is Si system
CGS System:it measure in length in centimeter mass in gram time in second
(ik it says physics but astronomy is a field of physics sooo) A recently discovered planet in a different solar system is located 1.85 x 10^15 Miles from earth. To the nearest 10th of a light year, how far is this planet from earth? ly= 8.6
The distance, to the nearest tenth, is 314.9 light-years.
The given data is:
A recently discovered planet is located 1.85*10^5 miles from Earth.
Now we want to transform this distance to light-years.
Remember that a light-year is defined as "the distance that the light would travel in one year".
using the relation:
distance = speed*time
The speed of light is:
speed = 6.706*10^8 mi/h
And in one year has 8760 hours, then we have:
time = 8760 h
replacing these in the equation we get:
distance = speed*time
distance = (6.706*10^8 mi/h)*(8760 h) = 5,874,456,000,000 miles
Son one light-year is equivalent to 5,874,456,000,000 miles
1 light-year = 5,874,456,000,000 miles
So to transform a distance in miles to light-years, we just need to divide that distance by 5,874,456,000,000 miles:
The distance between the new planet and Earth was:
D = 1.85*10^15 mi = ( 1.85*10^15)/(5,874,456,000,000) = 314.9 light-years.
if you want to learn more about this, you can read:
https://brainly.com/question/1302132
What are the units for speed?
O A. km/s2
O B. m/s2
O C. m/s2
O D. m/s
Answer:
Explanation:
The only one that doesn't have a time unit that is squared is the one that is a label for speed or velocity. Acceleration has a label with the time unit squared, like m/s/s. Choice D is the only unit for speed/velocity.
Answer: D
Explanation: metres per second (m/s)
The 11 th one please! Somebody help me:(
Answer:
203360Pa
Explanation:
Pressure= density of liquid*height*g
=1000*10*10
=100000Pa
Total pressure= water pressure + atmospheric pressure
=1000000+103360
=203360 Pascal
a motorcycle covers 500 meters in 25 seconds. calculate the average velocity
Vtb xe máy là:
v=s : t= 500 : 25=20(m/s)
Who would most likely be required to work with sodium hydroxide?
Answer:
a plumber
Explanation:
which physical property of the gas molecules gives the measurement of temperature
The temperature of a gas molecule is measured by the average translational kinetic energy
Answer:
The temperature of a gas is a measure of the average translational kinetic energy of the molecules. In a hot gas, the molecules move faster than in a cold gas; the mass remains the same, but the kinetic energy, and hence the temperature, is greater because of the increased velocity of the molecules
Explanation:
This is also from Go0gle because my explanation would've been an essay long .
but in shorter version if the gas molecules move fast it's hot an if it moves slow its cold hope this helps .
A apartie undergoes two displacement.The one has amagnitude of 150cm and makes an angle of 120 degrees with that positive x-axis.The resultant of the two displacement is 140cm at 35 degrees to the positive x-axis .Find the magnitude and direction of second displacement
Answer:
A = 150 cm at 120 degc
Where A + B = C find B
B = C - A add -A to both sides
Ax = 150 cos 60 = -75
Ay = 150 sin 60 = 129.9
Likewise
Cx = 114.7
Cy = 80.3
Bx = Cx - Ax = 114.7 + 75 = 189.7
By = Cy - Ay = 80.3 -129.9 = -49.6
B = (189.7^2 + 49.6^2)^1/2 = 196.7 length of B vector
tan B = By / Bx = -49.6 / 189.7 B = -14.65 deg
Also
sin B = By / B = -49.6 / 196.1 = -14.65 deg
So B is 196.1 cm at -14.65 deg
Un globo contiene 4 moles de un gas ideal con un volúmen de 5,0 L. Si se agregan 8 moles adicionales del gas a presión y temperatura constantes, ¿Cuál será el volumen final del globo? - ¿Cuál es la densidad (en g / L) de un gas con una masa molar de 60 g / mol a 0,75 atm y 27 ° C?
Tenemos un problema de termodinamica sobre gases ideales, los cuales pueden ser descritos por la ecuación de estado del gas ideal
[tex]P*V = n*R*T[/tex]
donde:
P = presión
V = volumen
n = número de moles
R = constante de los gases
T = temperatura.
1) Para el primer problema podemos pensar que el gas dentro del globo es un gas ideal:
Originalmente sabemos que n = 4 y V = 5.0 L
Entonces tendremos:
[tex]P*(5.0 L) = (4 moles)*R*T[/tex]
Ahora decidimos agregar 8 moles más, dejando constante la presión y la temperatura, entonces podemos reescribir la ecuación de arriba como:
(5.0L)/(4 moles) = R*T/P
Y como R, T y P son constantes, entonces:
R*T/P es una constante.
Esto quiere decir que cuando agreguemos 8 moles, para tener un total de 12 moles, tendremos que:
V'/(12 moles) = R*T/P = (5.0L)/(4 moles)
Donde V' es el nuevo volumen final del globo, y es lo que queremos obtener.
V'/(12 moles) = (5.0L)/(4 moles)
V' = (5.0L)*(12 moles)/(4 moles) = (5.0 L)*3 = 15.0 L
2) Queremos obtener la densidad en gramos sobre litro de un gas con una masa molar de 60g/mol, a P = 0.75 atm y T = 25°C.
Primero pasemos la temperatura a grados kelvin:
T = 25°C = (25 + 273.15)°K = 298.15°K
Planteamos la ecuación del gas ideal:
[tex]P*V = n*R*T[/tex]
reemplazando R = 0.082 (atm*L/mol*k), además de la presión y la temperatura para un solo mol de gas:
[tex](0.75 atm)*V = (1 mol)*(0.082 (atm*L/mol*k))*(298.15°K)[/tex]
Resolviendo para V obtenemos que:
[tex]V = (1 mol)*(0.082 (atm*L/mol*k))*(298.15°K)/(0.75 atm) = 32.597 L[/tex]
Así, vemos que un mol de este gas ocupa un volumen de 32.597 L
Y también sabemos que un mol de este gas pesa 60 gramos.
Recordando que la densidad es el cociente entre la masa y el volumen, podemos ver que la densidad del gas será:
[tex]d = 60g/(32.597 L) = 1.84 g/L[/tex]
Si deseas leer mas sobre el tema, podes ver:
https://brainly.com/question/18528542
The law of conservation of energy states that energy cannot be created or
destroyed, only converted into other forms.
True or false
Answer:
TrueExplanation:
Yes, According to law of conservation of energy, it has been said that energy cannot be created or destroyed.
what can be done to increase speed of rotation of a DC motor
Answer: There are multiple options:
By varying the supply voltage.
By varying the flux, and by varying the current through the field winding.
By varying the armature voltage, and by varying the armature resistance.
Helpful Link:
https://www.elprocus.com/what-are-the-best-ways-to-control-the-speed-of-dc-motor/
What is Plancks Constant? Need it ASAP
Answer:
The Planck constant, or Planck's constant, is a fundamental physical constant denoted h, and is of fundamental importance in quantum mechanics. A photon's energy is equal to its frequency multiplied by the Planck constant. Due to mass–energy equivalence, the Planck constant also relates mass to frequency.
Theory:Planck postulated that the energy of light is proportional to the frequency, and the constant that relates them is known as Planck's constant (h). His work led to Albert Einstein determining that light exists in discrete quanta of energy, or photons.
E = hf
[tex] \sf \: h = 6.626 \times {10}^{ - 34} \: kg \: {m}^{2} {s}^{ - 1} [/tex]
Does the scalar addition obey ordinary addition rules?
Explanation:
In scalar addition we have to do only the sum of magnitude as we know that the scalar quantities don't have direction.
since it is the scalar quantity the direction will be same for all the magnitudes.
Answer:
In scalar addition we have to do only the sum of magnitude as we know that the scalar quantities don't have direction...
since it is the scalar quantity the direction will be same for all the magnitudes.
on the other hand if it was a vector addition then it should be with two different directions which are considerable show the resultant vector needs to be calculated by vector addition method.
Which one of the following explains how light energy helps us see all kinds of objects around us?
a flashlight shining light on a book
Light is absorbed by the objects and does not reach our eyes.
The objects emit light that enters our eyes.
Light reflects off the objects and enters our eyes.
Light travels in a straight line until it enters our eyes.
Answer:
light reflects off the objects and enter our eyes
A tightrope walker is walking between two buildings holding a pole with length L=14.0 m, and mass mp=17.5 kg. The daredevil grips the pole with each hand a distance d=0.595 m from the center of the pole. A bird of mass mb=560 g lands on the very end of the left‑hand side of the pole. Assuming the daredevil applies upward forces with the left and right hands in a direction perpendicular to the pole, what magnitude of force Fleft and Fright must the left and right hand exert to counteract the torque of the bird?
Answer:
F = 32.28 N
Explanation:
For this exercise we must use the rotational equilibrium relation
Σ τ = 0
In the initial configuration it is in equilibrium, for which all the torque and forces are compensated. By the time the payment lands on the bar, we assume that the counter-clockwise turns are positive.
W_bird L / 2 - F_left 0.595 - F_right 0.595 = 0
we assume that the magnitude of the forces applied by the hands is the same
F_left = F_right = F
W_bird L / 2 - 2 F 0.595 = 0
F = [tex]\frac{m_{bird} \ g L} { 4 \ 0.595}[/tex]
we calculate
F = 0.560 9.8 14.0 /2.38
F = 32.28 N
why is the fuse used in a circuit called safety fuse?
Answer:
The maximum current which can flow through a fuse without melting it, is called its rating. ... If current higher than 8 A flows through the fuse, it would melt and circuit gets broken. ... Hence, fuse acts as a safety device
Answer:
The guy above me is right
Explanation:
Convert 400 mm to m using the method of dimensional analysis
Answer:
To convert 400 mm to m you can apply the formula [m] = [mm] / 1000; use 400 for mm. Thus, the conversion 400 mm m is the result of dividing 400 by 1000. 0.4
PLEASE MARK AS BRAINLIEST ANSWER
I shared a picture of the problem. It’s a basic Physics question and an Algebra question.
Hence the expression of ω in terms of m and k is
[tex]\omega = \sqrt{\frac{k}{m}[/tex]
Given the expressions;
[tex]T_s = 2 \pi \sqrt{\frac{m}{k} } \ and \ T_s = \frac{2 \pi}{\omega}[/tex]
Equating both expressions we will have;
[tex]2 \pi \sqrt{\frac{m}{k} } = \frac{2 \pi}{\omega}[/tex]
Divide both equations by 2π
[tex]\frac{2 \pi\sqrt{\frac{m}{2 \pi} } }{2 \pi}=\frac{\frac{2 \pi}{\omega} }{2\pi}\\\sqrt{\frac{m}{2 \pi} } = \frac{1}{\omega}\\[/tex]
Square both sides
[tex](\sqrt{\frac{m}{k} } )^2 = (\frac{1}{\omega} )^2\\\frac{m}{k} = \frac{1}{\omega ^2} \\\omega ^2 = \frac{k}{m}[/tex]
Take the square root of both sides
[tex]\sqrt{\omega ^2} =\sqrt{\frac{k}{m} } \\\omega = \sqrt{\frac{k}{m}[/tex]
Hence the expression of ω in terms of m and k is
[tex]\omega = \sqrt{\frac{k}{m}[/tex]
Learn more about subject of the formula here: https://brainly.com/question/19557491
derive an expression for resistivity of conductor of length l and area of cross section A
Answer
Resistivity R = K * L / A where resistivity is constant for material, L the length of the material and A the area of the material
K = R * A / L where R is the resistance of the material
Plz Help me thank uuu...
Which of these is a likely impact of the stronger than normal trade winds on the eastern Pacific ocean?
Warm surface water builds up, causing lower than average temperature.
Warm surface water builds up, causing higher than average temperature.
Warm surface water is reduced, causing colder conditions than normal.
Warm surface water is reduced, causing hotter conditions than normal.
Answer:
Jet stream would be displaced southwards causing heavy rain and flooding.
Explanation:
The other options of the question were A) Jet stream would be displaced northwards causing drought. B) Jet stream would be displaced southwards causing drought. D) Jet stream would be displaced northwards causing heavy rain and flooding,
The statement that is a likely impact of stronger than normal trade winds in the Pacific Northwest to the United States is "Jet stream would be displaced southwards causing heavy rain and flooding."
We are talking about climate or weather terminology. In this case, we are referring to the "El Niño" (the Children) effect. Its presence affects the weather in North America. This phenomenon combines with the "La Niña) effect and it presents itself every two to seven years, ad they last from 8 to 12 months, affecting the weather conditions of the region.
Answer:
jet stream should be displaced southwards which causes heavy rainfall and flood.
Logam P dan Q sejenis. Logam P yang memiliki panjang 1 meter dipanaskan hingga mengalami kenaikan suhu 12ºC, akibatnya logam bertambah panjang 0,2 cm. Logam Q juga dipanaskan hingga mengalami kenaikan suhu 10°C dan panjangnya bertambah 0,1 cm. Tentukanlah panjang mula-mula logam Q!
Answer:
I don't know ???
sorry
Which statement best describes the arrangement of electrons in an atom of fluorine (F)?
(1 point) giving brainliest for sure
There are two electrons in the first energy level and seven electrons in the second energy level.
There are two electrons in the first energy level and five electrons in the second energy level.
There are five electrons in the first energy level and two electrons in the second energy level.
There are seven electrons in the first energy level and two electrons in the second energy level.
Flourine is an element which has 9 electrons. The first energy level can only hold upto 2 electrons so therefore two electrons of the fluorine element will be in the first orbital.
In the second orbital there will be seven electrons. The configuration will be as 1s2, 2s2 , 2p5 .
The first orbital has capacity of two electrons and then the remaining two electrons will be in higher second energy level.
The further 5 electrons will be in lower second energy level which is denoted by p.
Learn more at https://brainly.com/question/24373325
Answer:
#1. 5
#2.They have valence electrons in the same energy level.
#3. Helium atoms have 2 valence electrons, while atoms of the other elements in the group all have 8 valence electrons.
#4. cesium (Cs)
#5. There are two electrons in the first energy level and seven electrons in the second energy level.
Explanation:
Q- Wheel of a running vehicle has which energy?
(a) Vibrational Kinetic energy
(b) Translational Kinetic energy
(c) Rotational Kinetic energy
(d) All of the above
Answer:
Rotational kinetic energy
Explanation:
It is caused by circular motion.
How can a simulation study be used to learn about a planet we have never visited?
In a simulation study you imitate some conditions and characteristics of the real planet. The simulation can be used as a substitute for real data collected on the planet.
Simulation studies can be used for planets we have already visited.
In a simulation study you imitate as many conditions and characteristics as possible of the real thing, in this case the planet you have not visited. By simulating as many conditions as possible you can visualize what the planet might be like and learn things about it without actually visiting it.
Simulation studies cannot be used to learn about a planet we have never visited because we do not know anything about the planet.
A simulation study that is used to learn about a planet by simulating as many conditions as possible, you can visualize what the planet might be like and learn things about it without actually visiting it. The correct option is c.
What is simulation?A simulation is a method of simulating a process or change in the actual world to forecast future events or to explain past events and their causes. These days, simulations are frequently carried out using computers. Scientists use simulations to find answers and to test complicated systems.
A fire drill is used in this instance to get everyone ready for an impending event. In fire drills, the fire alarm is sounded even when there isn't actually a fire.
Therefore, the correct option is c.
To learn more about simulation, refer to the link:
https://brainly.com/question/16359096
#SPJ2
Ag,Au and Cu are called coinage metals why plzzzz hurry its urgent plzzz
Answer:
This is because these metals are used for minting (making) coins.
Answer:
It is bcz it is used for making coins
Those of you who have recently finished high school physics-did you struggle? If you did, where did you most struggle in? Was it the tests? Or a specific topic?
Thank you!
Answer:
I'm over halfway through it so don't have a complete answer but i think you just need to keep ontop of everything and write down all the key equations on flashcards or something and aim to learn them at the beginning of each topic. i found the longer questions hard so recommend practising those
Explanation:
3. Calculate the wavelength of wave that has a frequency of 4.75 x 1012Hz.
a. 1.43 x 1021 m
b. 6.31 x 105 m
1.58 x 104 m
d. 6.31 x 105 m
please help
C.
We know
[tex]\boxed{\sf \lambda=\dfrac{C}{V}}[/tex]
[tex]\\ \sf\longmapsto \lambda=\dfrac{3\times 10^8ms^{-1}}{4.75\times 10^{12}s^{-1}}[/tex]
[tex]\\ \sf\longmapsto \lambda=0.631\times 10^{-4}m[/tex]
[tex]\\ \sf\longmapsto \lambda=6.31\times 10^{-5}m[/tex]
