4. An aluminum alloy fin of 12 mm thick, 10 mm width and 50 mm long protrudes from a wall, which is maintained at 120C. The ambient air temperature is 22C. The heat transfer coefficient and conductivity of the fin material are 140 W/m2K and 55 W/mk respectively. Determine a. Temperature at the end of the fin b. Temperature at the middle of the fin. c. Calculate the heat dissipation energy of the fin
Answer:
a) 84.034°C
b) 92.56°C
c) ≈ 88 watts
Explanation:
Thickness of aluminum alloy fin = 12 mm
width = 10 mm
length = 50 mm
Ambient air temperature = 22°C
Temperature of aluminum alloy is maintained at 120°C
a) Determine temperature at end of fin
m = √ hp/Ka
= √( 140*2 ) / ( 12 * 10^-3 * 55 )
= √ 280 / 0.66 = 20.60
Attached below is the remaining answers
: Một nền kinh tế có cấu trúc như sau:
C = 80 + 0,8(Y - T); T = 100 ;
I = 130; G = 120;
MSr = MS/CPI = 200;
MD = 0,2Y – 10i
Yêu cầu:
1. Xác định thu nhập và lãi suất cân bằng?
2. Muốn sản lượng cân bằng tăng 500 thì chính phủ cần thay đổi thuế như thế nào?
3. Liệu mục tiêu ở câu 2 có thể đạt đựơc bằng chính sách tiền tệ hay không? Tại sao?
Answer:
Haha I'm a great guy but my friend has been in a day of the day and a lot to be able and I'm happy holi and a lot to the world of the day and day to
Determine the voltage which must be applied to a 1 k 2 resistor in order that a current of
10 mA may flow.
Answer:
The correct solution is "20 volt".
Explanation:
Given that:
Current,
I = 10 mA
or,
= [tex]10\times 10^{-3} \ A[/tex]
Resistance,
R = 2 K ohm
or,
= [tex]1\times 10^3 \ ohm[/tex]
Now,
The voltage will be:
⇒ [tex]V=IR[/tex]
By putting the values, we get
[tex]=10\times 10^{-3}\times 2\times 10^{3}[/tex]
[tex]= 20 \ volt[/tex]
Type the correct answer in each box. Spell all words correctly. According to the priority matrix, which tasks should an entrepreneur complete first? According to the priority matrix, entrepreneurs should first complete tasks that are blank and important.
Answer:
Development of creative and develop ideas
Explanation:
First task as an entrepreneur is to be creative and develop ideas. The person must design the product based on which he will develop the business strategy.
The remaining activities such as marketing, fund raising, recruitment etc. comes at a later stage.
What possible scenarios may happen if you do the task without using PPE?
Even though the content of many alcohol blends doesn’t affect engine drive ability using gasoline with alcohol in warm weather may cause
The number of pulses per second from IGBTs is referred to as
Convert the following indoor air quality standards, established by the U.S. Occupational Safety and Health Administration (OSHA), from ppmv to mg/m3 (at 25°C and 1atm) or vice versa.
a. Carbon dioxide (CO2), 5,000 ppmv
b. Formaldehyde (HCHO), 3.6 mg/m^3
c. Nitric oxide (NO), 25 ppmv
. En la facultad de Ingeniería Industrial se realizó una encuesta a 200 personas para saber que lenguaje de programación preferían para aprender al inicio, se obtuvo: 50 prefieren C, 65 prefieren C#, 77 prefieren Python, 100 prefieren C o C#, 105 prefieren C# o Python, 110 prefieren C o Python, 10 personas prefieren C y Python pero no C#.
Answer:
lalalalapumpe
Explanation:
What is the key objective of data analysis
Answer: The process of data analysis uses analytical and logical reasoning to gain information from the data. The main purpose of data analysis is to find meaning in data so that the derived knowledge can be used to make informed decisions.
A cylindrical space capsule lands in the ocean. This capsule is 2.44 m long, 1.10 m in diameter, and weighted at one end so that it floats with its long central axis vertical and 0.820 m of its length above the water surface. The mass density of sea water is 1025 kg/m3.What is the magnitude of the buoyant force exerted on the capsule?
Answer:
The correct answer is "15456.8 N".
Explanation:
According to the question,
The inside volume will be:
= [tex]3.14\times (\frac{1.1}{2} )^2\times (2.44-0.82)[/tex]
= [tex]3.14\times \frac{1.21}{4}\times 1.62[/tex]
= [tex]3.14\times 03025\times 1.62[/tex]
= [tex]1.538757 \ m^3[/tex]
hence,
The buoyant force will be:
= [tex]V\times Pw\times g[/tex]
= [tex]1.538757\times 1025\times 9.8[/tex]
= [tex]15456.8 \ N[/tex]
Given below are the measured streamflows in cfs from a storm of 6-hour duration on a stream having a drainage area of 185 mi^2. Derive the unit hydrograph by the inverse procedure. Assume a constant baseflow of 550 cfs.
Hour Day 1 Day 2 Day 3 Day 4
Midnight 550 5,000 19,000 550
6 am 600 4,000 1400
Noon 9000 3000 1000
6 pm 6600 2500 750
Answer:
33.56 ft^3/sec.in
Explanation:
Duration = 6 hours
drainage area = 185 mi^2
constant baseflow = 550 cfs
Derive the unit hydrograph using the inverse procedure
first step : calculate for the volume of direct runoff hydrograph using the details in table 2 attached below
Vdrh = sum of drh * duration
= 29700 * 6 hours ( 216000 secs )
= 641,520,000 ft^3.
next step : Calculate the volume of runoff in equivalent depth
Vdrh / Area = 641,520,000 / 185 mi^2
= 1.49 in
Finally derive the unit hydrograph
Unit of hydrograph = drh / volume of runoff in equivalent depth
= 50 ft^3 / 1.49 in = 33.56 ft^3/sec.in
Calculate the biaxial stresses σ1 and σ2 for the biaxial stress case, where ε1 = .0020 and ε2 = –.0010 are determined experimentally on an aluminum member of elastic constants, E = 71 GPa and v = 0.35. Also, determine the value for the maximum shear stress.
Answer:
i) σ1 = 133.5 MPa
σ2 = -2427 MPa
ii) 78.89 MPa
Explanation:
Given data:
ε1 = 0.0020 and ε2 = –0.0010
E = 71 GPa
v = 0.35
i) Determine the biaxial stresses σ1 and σ2 using the relations below
ε1 = σ1 / E - v (σ2 / E) -----( 1 )
ε2 = σ2 / E - v (σ1 / E) -------( 2 )
resolving equations 1 and 2
σ1 = E / 1 - v^2 { ε1 + vε2 } ---- ( 3 )
σ2 = E / 1 - v^2 { ε2 + vε1 } ----- ( 4 )
input the given data into equation 3 and equation 4
σ1 = 133.5 MPa
σ2 = -2427 MPa
ii) Calculate the value of the maximum shear stress ( Zmax )
Zmax = ( σ1 - σ2 ) / 2
= 133.5 - ( - 2427 ) / 2
= 78.89 MPa
A brittle material is subjected to a tensile stress of 1.65 MPa. If the specific surface energy and modulus of elasticity for this material are 0.60 J/m2 and 2.0 GPa, respectively. What is the maximum length of a surface flaw that is possible without fracture
Answer:
The maximum length of a surface flaw that is possible without fracture is
[tex]2.806 \times 10^{-4} m[/tex]
Explanation:
The given values are,
σ=1.65 MPa
γs=0.60 J/m2
E= 2.0 GPa
The maximum possible length is calculated as:
[tex]\begin{gathered}a=\frac{2 E \gamma_{s}}{\pi \sigma^{2}}=\frac{(2)\left(2 \times 10^{9} \mathrm{~N} / \mathrm{m}^{2}\right)(0.60 \mathrm{~N} / \mathrm{m})}{\pi\left(1.65\times 10^{6} \mathrm{~N} / \mathrm{m}^{2}\right)^{2}} \\=2.806 \times 10^{-4} \mathrm{~m}\end{gathered}[/tex]
The maximum length of a surface flaw that is possible without fracture is
[tex]2.806 \times 10^{-4} m[/tex]
Hi, can anyone draw me an isometric image of this shape?
An engineer is applying dimensional analysis to study the flow of air through this horizontal sudden contraction for the purpose of characterizing the pressure drop. The flow is being modeled as constant density and steady. What is the functional relationship of the variables that characterize this situation
Answer:
The answer is " [tex]\Delta p = f(V1, p, V2, d, D, L)[/tex]"
Explanation:
Please find the complete question in the attached file.
Its change in temperature in pipes depends on rate heads and loss in pipes owing to pipe flow, contractual loss, etc.
The temperature change thus relies on V1 v2 p d D L.
An air conditioner removes heat steadily from a house at a rate of 750 kJ/min while drawing electric power at a rate of 5.25 kW. Determine (a) the COP of this air conditioner and (b) the rate of heat transfer to the outside air.Answers:(a) 2.38, (b) 1065 kJ/min
Answer:
a) the COP of this air conditioner is 2.38
b) the rate of heat transfer to the outside air is 1065 kJ/min
Explanation:
Given the data in the question;
[ Outdoor ] ← Q[tex]_H[/tex] [ W[tex]_{net, in[/tex] ] Q[tex]_L[/tex] ← [ House ]
Rate of heat removed from the house; Q[tex]_L[/tex] = 750 kJ/min = ( 750 kJ/min × ( 1 kW / 60 kJ/min ) ) = 12.5 kW
Net-work input; W[tex]_{net, in[/tex] = 5.25 kW
a) The coefficient of performance of the air conditioner; COP.
COP = Q[tex]_L[/tex] / W[tex]_{net, in[/tex]
we substitute
COP = 12.5 kW / 5.25 kW
COP = 2.38
Therefore, the COP of this air conditioner is 2.38
b) the rate of heat transfer to the outside air.
Q[tex]_H[/tex] = Q[tex]_L[/tex] + W[tex]_{net[/tex]
we substitute
Q[tex]_H[/tex] = 12.5 kW + 5.25 kW
Q[tex]_H[/tex] = 17.75 kW
Q[tex]_H[/tex] = ( 17.75 × 60 ) kJ/min
Q[tex]_H[/tex] = 1065 kJ/min
Therefore, the rate of heat transfer to the outside air is 1065 kJ/min
Question
А
Particle of 2kg mass is being pulled across a smooth horizontal
surface by a horizontal force. The force does 24 Joule of work in
increasing
the particle's
velocity from 5m/s
to v m/s. calculate
the value of v and the position of particle
after 15s
Answer:
udhddhdiejebdidjebdhdidh
