Explain how surface waves can have characteristics of both longitudinal waves and transverse waves. Please use 3 content related sentences

Answers

Answer 1

Answer: Search Results

Featured snippet from the web

Answer: Surface waves can have characteristics of both longitudinal and transverse waves in the following way; The motion of the surface waves is up and down which is perpendicular to the direction of the wave. This is similar to the motion of transverse waves whereas the the motion of longitudinal.

Explanation:

Answer 2

Surface waves can exhibit characteristics of both longitudinal waves and transverse waves.

Surface waves are a type of mechanical wave that propagate along the interface between two different mediums, such as the ground and air or the surface of water. These waves combine properties of both longitudinal and transverse waves

Similar to longitudinal waves, surface waves involve particles oscillating in the same direction as the wave propagation. This creates compressions and rarefactions, leading to variations in density or pressure. These compressions and rarefactions are characteristic of longitudinal waves.

However, surface waves also exhibit transverse motion. As the wave propagates along the surface, particles move in a perpendicular direction to the wave's motion. This transverse motion causes particles to displace vertically or horizontally, similar to transverse waves.

By combining both longitudinal and transverse characteristics, surface waves possess a complex motion that allows them to travel along the surface while simultaneously causing particles to oscillate both parallel and perpendicular to the direction of wave propagation.

To know more about Surface waves, click here.

https://brainly.com/question/907481

#SPJ2


Related Questions

It is just as difficult to accelerate a car on a level horizontal surface on the Moon as it is here on Earth because

Answers

Answer:

Mass of the car is independent of gravity

Explanation:

Here, we want to state the reason why even though we have the acceleration due to gravity absent on the moon, it is still difficult to accelerate a car on a level horizontal level on the moon.

The answer to this is that the mass of the car that we want to accelerate is independent of gravity.

Had it been that gravity has an effect on the mass of the said car, then we might conclude that it will not be difficult to accelerate the car on a horizontal surface on the moon.

But due to the fact that gravity has no effect on the mass of the car to be accelerated, then the problem we have on earth with accelerating the car is the same problem we will have on the moon if we try to accelerate the car on a horizontal level surface.

3. What color of laser light shines through a diffraction grating with a line density of 500 lines/mm if the third maxima from the central maxima (m=3) is at an angle of 45°?

Answers

Answer:

Wavelength is 471 nm

Explanation:

Given that,

Lines per unit length of diffraction grating is 500 lines/mm.

The third maxima from the central maxima (m=3) is at an angle of 45°

We need to find the color of laser light shines through a diffraction grating.

The condition for maxima is :

[tex]d\sin\theta=m\lambda[/tex]

d = 1/N, N = number of lines per mm

[tex]\lambda=\dfrac{1}{Nm}\sin\theta\\\\\lambda=\dfrac{10^{-3}}{500\times 3}\sin(45)\\\\\lambda=4.31\times 10^{-7}\\\\\text{or}\\\\\lambda=471\ nm[/tex]

Astronomers discover an exoplanet (a planet of a star other than the Sun) that has an orbital period of 3.75
Earth years in its circular orbit around its sun, which is a star with a measured mass of 3.23×1030kg
. Find the radius of the exoplanet's orbit.

Answers

Answer:

[tex]r=4.24\times 10^{11}\ m[/tex]

Explanation:

Given that,

Orbital time period, T = 3.75 earth years

Mass of star, [tex]m=3.23\times 10^{30}\ kg[/tex]

We need to find the radius of the exoplanet's orbit. It is a concept of Kepler's third law of motion i.e.

[tex]T^2=\dfrac{4\pi^2}{GM}r^3[/tex]

r is the radius of the exoplanet's orbit.

Solving for r we get :

[tex]r=(\dfrac{T^2GM}{4\pi^2})^{1/3}[/tex]

We know that, [tex]1\ \text{earth year}=3.154\times 10^7\ \text{s}[/tex]

So,

[tex]r=(\dfrac{(3.75\times 3.154\times 10^7)^2\times 6.67\times 10^{-11}\times 3.23\times 10^{30}}{4\pi^2})^{1/3}\\\\r=4.24\times 10^{11}\ m[/tex]

So, the radius of the exoplanet's orbit is [tex]4.24\times 10^{11}\ m[/tex].

Monochromatic light falls on two very narrow slits 0.047 mm apart. Successive fringes on a screen 6.60 m away are 8.9 cm apart near the center of the pattern.
Determine the wavelength and frequency of the light.

Answers

Answer::

   [tex]\lambda = 634 nm[/tex]

  [tex]f = 4.73 *10^{14} \ Hz[/tex]

Explanation:

From the question we are told that

      The  distance of separation is  [tex]d = 0.047 \ mm = 0.047 *10^{-3} \ m[/tex]

       The  distance of the screen is  [tex]D = 6.60 \ m[/tex]

      The  width of the fringe is [tex]y = 8.9 \ cm = 0.089 \ m[/tex]

     

Generally the width of the width of the fringes is mathematically represented as

          [tex]y = \frac{\lambda * D }{d }[/tex]

=>       [tex]\lambda = \frac{y * d }{D }[/tex]

=>      [tex]\lambda = \frac{ 0.089 * (0.047 *10^{-3}) }{6.60 }[/tex]

=>    [tex]\lambda = 634 *10^{-9}[/tex]

=>  [tex]\lambda = 634 nm[/tex]

Generally the speed of light is mathematically represented as

         [tex]c = f * \lambda[/tex]

=>       [tex]f= \frac{ c}{\lambda }[/tex]

=>         [tex]f= \frac{ 3.0 *10^{8}}{634 *10^{-9}}[/tex]

=>     [tex]f = 4.73 *10^{14} \ Hz[/tex]

Expectant mothers many times see their unborn child for the first time during an ultrasonic examination. In ultrasonic imaging, the blood flow and heartbeat of the child can be measured using an echolocation technique similar to that used by bats. For the purposes of these questions, please use 1500 m/s as the speed of sound in tissue. I need help with part B and C
To clearly see an image, the wavelength used must be at most 1/4 of the size of the object that is to be imaged. What frequency is needed to image a fetus at 8 weeks of gestation that is 1.6 cm long?
A. 380 kHz
B. 3.8 kHz
C. 85 kHz
D. 3.8 MHz

Answers

Answer:

380 kHz

Explanation:

The speed of sound is taken as 1500 m/s

The length of the fetus is 1.6 cm long

The condition is that the wavelength used must be at most 1/4 of the size of the object that is to be imaged.

For this 1.6 cm baby, the wavelength must not exceed

λ = [tex]\frac{1}{4}[/tex] of 1.6 cm = [tex]\frac{1}{4}[/tex] x 1.6 cm = 0.4 cm =

0.4 cm = 0.004 m   this is the wavelength of the required ultrasonic sound.

we know that

v = λf

where v is the speed of a wave

λ is the wavelength of the wave

f is the frequency of the wave

f = v/λ

substituting values, we have

f = 1500/0.004 = 375000 Hz

==> 375000/1000 = 375 kHz ≅ 380 kHz

Luz, who is skydiving, is traveling at terminal velocity with her body parallel to the ground. She then changes her body position to feet first toward the ground. What happens to her motion? She will continue to fall at the same terminal velocity because gravity has not changed. She will slow down because the air resistance will increase and be greater than gravity. She will speed up because air resistance will decrease and be less than gravity. She will begin to fall in free fall because she will have no air resistance acting on her.

Answers

Answer:

Option C - she will speed up because air resistance has reduced and be less than gravity

Explanation:

We are told that Luz is skydiving with terminal velocity and her body parallel to the ground. Now, at this point she will be experiencing a gravitational force acting downwards, and also air resistance as a result of the drag force on her body

Since the downward gravitational force on Luz is constant, she will fall with a net force of;

F_net = F_g - F_d

where;

F_net is the net force on Luz acting downwards

F_g is the gravitational force on Luz

F_d is the drag force on Luz

The drag force on her body is proportional to the surface area of attack.

We are now told that Luz changes her body position to feet first toward the ground. This means that the surface area of attack is reduced because the feet will consume less space than the frontal part of her body. Thus, the drag force will be lesser then before she changed her body position due to reduced air resistance on her body.

Now, from earlier, we saw that;

F_net = F_g - F_d

So, the lesser F_d is, the higher F_net becomes.

Thus, she will speed up because air resistance has reduced and be less than gravity.

Answer:

C

Explanation:

EDGE 2020

"In a Young's double-slit experiment, the slit separation is doubled. To maintain the same fringe spacing on the screen, the screen-to-slit distance D must be changed to"

Answers

Answer:

To maintain the same fringe spacing on the screen, the screen-to-slit distance D must be changed to a value 2D that is twotimes D

1. Rank the transformers on the basis of their rms secondary voltage. Rank from largest to smallest.
Vp = 240 V; Np = 1000 turns; Ns = 2000 turns
Vp = 480 V; Np = 4000 turns; Ns = 2000 turns
Vp = 480 V; Np = 2000 turns; Ns = 1000 turns
Vp = 120 V; Np = 500 turns; Ns = 2000 turns
Vp = 240 V; Np = 1000 turns; Ns = 500 turns
2. 100 A of rms current is incident on the primary side of each transformer. Rank the transformers on the basis of their rms secondary current. Rank from largest to smallest.
Vp = 240 V; Np = 1000 turns; Ns = 2000 turns
Vp = 480 V; Np = 2000 turns; Ns = 1000 turns
Vp = 240 V; Np = 1000 turns; Ns = 500 turns
Vp = 120 V; Np = 500 turns; Ns = 2000 turns
Vp = 480 V; Np = 4000 turns; Ns = 2000 turns

Answers

Answer:

1. Transformer 3> Transformer 1 and 2 > Transformer 4

2. Transformer 2,3,5 > Transformer 1 > Transformer 4

Explanation:

From;

Vs/Vp = Ns/Np

Where;

Vp= voltage in primary coil

Vs= voltage in secondary coil

Ns= number of turns in secondary coil

Np= number of turns in primary coil.

Vs= Ns×Vp/Np

Vs= 480 ×2000/4000

Vs= 240 V

Vs= 480 ×1000/2000

Vs=240 V

Vs= 120 × 2000/500

Vs= 480 V

Vs= 240 × 500/1000

Vs= 120 V

2. Ns/Np= Ip/Is

Is= Np×Ip/Ns

Is= 1000 × 100/2000

Is= 50 A

Is= 2000 × 100/1000

Is= 200 A

Is= 1000 × 100/500

Is= 200 A

Is= 500 × 100/2000

Is= 25 A

Is= 4000 × 100/2000

Is= 200 A

An engine causes a car to move 10 meters with a force of 100 N. The engine produces 10,000 J of energy. What is the efficiency of this engine?

Answers

Answer:

10%

Explanation:

Efficiency = work done / energy used

e = (10 m × 100 N) / (10,000 J)

e = 0.1

The efficiency is 0.1, or 10%.

Describe and name the different types of collision. In which are the linear momentum and kinetic energy conserved

Answers

Answer:

1. Elastic collision

2. Inelastic collision    

Explanation:

Elastic collision: collision is said to be elastic if total kinetic energy is not conserved and if there is a rebound after collision

the collision is described by the equation bellow

[tex]m1U1+ m2U2= m1V1+m2V2[/tex]

Inelastic collision: this type of collision occurs when the total kinetic energy of a body is conserved or when the bodies sticks together and move with a common velocity

the collision is described by the equation bellow

[tex]m1U1+ m2U2= V(m1+m2)[/tex]

Mention the importance of writing the physical quantities as vectors.​

Answers

Answer:

Knowledge of vectors is important because many quantities used in physics are vectors. If you try to add together vector quantities without taking into account their direction you'll get results that are incorrect.

Explanation:

An example of the importance of vector addition could be the following:

Two cars are involved in a collision. At the time of the collision car A was travelling at 40 mph, car B was travelling at 60 mph. Until I tell you in which directions the cars were travelling you don't know how serious the collision was.

The cars could have been travelling in the same direction, in which case car B crashed into the back of car A, and the relative velocity between them was 20 mph. Or the cars could have been travelling in opposite directions, in which case it was a head on collision with a relative velocity between the cars of 100 mph!

What is the maximum wavelength of incident light for which photoelectrons will be released from gallium

Answers

Answer:

292 nm

Explanation:

The work function of gallium ∅ = 94.25 eV = 6.81 x 10^-19 J

at maximum wavelength, the energy of the photons is equal to its work function

Energy of the electron = hf

but hf = hc/λ

where h is the planck's constant = 6.63 × 10-34 m^2 kg/s

c is the speed of light = 3 x 10^8 m/s

λ is the wavelength that this occurs, which is the maximum wavelength

Equating, we have

hc/λ =  ∅

substituting, we have

(6.63 × 10-34 x 3 x 10^8)/λ = 6.81 x 10^-19

(1.989 x 10^-25)/(6.81 x 10^-19) = λ

λ = 292.07 x 10^-9 = 292 nm

Which scientist proposed a mathematical solution for the wave nature of light?

Answers

Answer:

Explanation:

Christian Huygens

Light Is a Wave!

Then, in 1678, Dutch physicist Christian Huygens (1629 to 1695) established the wave theory of light and announced the Huygens' principle.

A mass m = 0.7 kg is released from rest at the origin 0. The mass falls under the influence of gravity. When the mass reaches point A, it is a distance x below the origin 0; when the mass reaches point B it is a distance of 3 x below the origin 0. What is vB/vA?

Answers

Answer:

[tex]v_B/v_A=\sqrt{3}[/tex]

Explanation:

Consider the two kinematic equations for velocity and position of an object falling due to the action of gravity:

[tex]v=-g\,t\\ \\position=-\frac{1}{2} g\,t^2[/tex]

Therefore, if we consider [tex]t_A[/tex] the time for the object to reach point A, and [tex]t_B[/tex] the time for it to reach point B, then:

[tex]v_A=-g\,t_A\\v_B=-g\,t_B\\\frac{v_B}{v_A}= \frac{-g\,t_B}{-g\,t_A} =\frac{t_B}{t_A}[/tex]

Let's work in a similar way with the two different positions at those different times, and for which we have some information;

[tex]x_A=-x=-\frac{1}{2}\, g\,t_A^2\\x_B=-3\,x=-\frac{1}{2}\, g\,t_B^2\\ \\\frac{x_B}{x_A} =\frac{t_B^2}{t_A^2} \\\frac{t_B^2}{t_A^2}=\frac{-3\,x}{-x} \\\frac{t_B^2}{t_A^2}=3\\(\frac{t_B}{t_A})^2=3[/tex]

Notice that this quotient is exactly the square of the quotient of velocities we are looking for, therefore:

[tex](\frac{t_B}{t_A})^2=3\\(\frac{v_B}{v_A})^2=3\\ \frac{v_B}{v_A}=\sqrt{3}[/tex]

A steel ball attached to a spring moves in simple harmonic motion. The amplitude of the ball's motion is 11.0 cm, and the spring constant is 6.00 N/m. When the ball is halfway between its equilibrium position and its maximum displacement from equilibrium, its speed is 26.1 cm/s. (a) What is the mass of the ball (in kg)? kg (b) What is the period of oscillation (in s)? s (c) What is the maximum acceleration of the ball? (Enter the magnitude in m/s2.) m/s2

Answers

Answer:

a) m = 0.626 kg , b) T = 2.09 s , c)   a = 1.0544 m / s²

Explanation:

In a spring mass system the equation of motion is

        x = A cos (wt + Ф)

with      w = √(k / m)

a) velocity is defined by

        v = dx / dt

        v = - A w sin (wt + Ф)          (1)

give us that the speed is

        v = 26.1 m / s

for the point

        x = a / 2

the range of motion is a = 11.0 cm

       x = 11.0 / 2

       x = 5.5 cm

Let's find the time it takes to get to this distance

       wt + Ф = cos⁻¹ (x / A)

       wt + Ф = cos 0.5

        wt + Ф = 0.877

In the exercise they do not indicate that the body started its movement with any speed, therefore we assume that for the maximum elongation the body was released, therefore the phase is zero f

       Ф = 0

       wt = 0.877

       t = 0.877 / w

we substitute in equation 1

       26.1 = -11.0 w sin (w 0.877 / w)

        w = 26.1 / (11 sin 0.877))

        w = 3.096 rad / s

from the angular velocity equation

       w² = k / m

       m = k / w²

       m = 6 / 3,096²

       m = 0.626 kg

b) angular velocity and frequency are related

       w = 2π f

frequency and period are related

        f = 1 / T

we substitute

        w = 2π / T

        T = 2π / w

        T = 2π / 3,096

        T = 2.09 s

c) maximum acceleration

 the acceleration of defined by

        a = dv / dt

        a = - Aw² cos (wt)

the acceleration is maximum when the cosine is ±1

         a = A w²

          a = 11  3,096²

        a = 105.44 cm / s²

we reduce to m / s

        a = 1.0544 m / s²

A sinusoidal electromagnetic wave is propagating in a vacuum in the +z-direction. If at a particular instant and at a certain point in space the electric field is in the +x-direction and has a magnitude of 4.00 V/m, what is the magnitude of the magnetic field of the wave at this same point in space and instant in time?

Answers

Answer:

B = 1.33 10⁻⁸ T , the magnetic field must be in the y + direction

Explanation:

In an electromagnetic wave the electric and magnetic fields are in phase

         c = E / B

         B = E / c

let's calculate

          B = 4.00 / 3 10⁸

          B = 1.33 10⁻⁸ T

To determine the direction we use that the electric and magnetic fields and the speed of the wave are perpendicular.

 If the wave advances in the + Z direction and the electric field is in the + x direction, the magnetic field must be in the y + direction

A sharp edged orifice with a 60 mm diameter opening in the vertical side of a large tank discharges under a head of 6 m. If the coefficient of contraction is 0.68 and the coefficient of velocity is 0.92, what is the discharge?

Answers

Answer:

The discharge rate is [tex]Q = 0.0192 \ m^3 /s[/tex]

Explanation:

From the question we are told that

   The  diameter is  [tex]d = 60 \ mm = 0.06 \ m[/tex]

    The  head is  [tex]h = 6 \ m[/tex]

     The  coefficient of contraction is  [tex]Cc = 0.68[/tex]

     The  coefficient of  velocity is  [tex]Cv = 0.92[/tex]

The radius is mathematically evaluated as

         [tex]r = \frac{d}{2}[/tex]

substituting values

        [tex]r = \frac{ 0.06 }{2}[/tex]

        [tex]r = 0.03 \ m[/tex]

The  area is mathematically represented as

      [tex]A = \pi r^2[/tex]

substituting values

      [tex]A = 3.142 * (0.03)^2[/tex]

      [tex]A = 0.00283 \ m^2[/tex]

 The  discharge rate is mathematically represented as

        [tex]Q = Cv *Cc * A * \sqrt{ 2 * g * h}[/tex]

substituting values

       [tex]Q = 0.68 * 0.92* 0.00283 * \sqrt{ 2 * 9.8 * 6}[/tex]

       [tex]Q = 0.0192 \ m^3 /s[/tex]

To get an idea of the order of magnitude of inductance, calculate the self-inductance in henries for a solenoid with 1500 loops of wire wound on a rod 13 cm long with radius 2 cm

Answers

Answer:

The self-inductance in henries for the solenoid is 0.0274 H.

Explanation:

Given;

number of turns, N = 1500 turns

length of the solenoid, L = 13 cm = 0.13 m

radius of the wire, r = 2 cm = 0.02 m

The self-inductance in henries for a solenoid is given by;

[tex]L = \frac{\mu_oN^2A}{l}[/tex]

where;

[tex]\mu_o[/tex] is permeability of free space = [tex]4\pi*10^{-7} \ H/m[/tex]

A is the area of the solenoid = πr² = π(0.02)² = 0.00126 m²

[tex]L = \frac{4\pi *10^{-7}(1500)^2*(0.00126)}{0.13} \\\\L = 0.0274 \ H[/tex]

Therefore, the self-inductance in henries for the solenoid is 0.0274 H.

Two coherent sources of radio waves, A and B, are 5.00 meters apart. Each source emits waves with wavelength 6.00 meters. Consider points along the line connecting the two sources.Required:a. At what distance from source A is there constructive interference between points A and B?b. At what distances from source A is there destructive interference between points A and B?

Answers

Answer:

a

    [tex]z= 2.5 \ m[/tex]

b

   [tex]z = (1 \ m , 4 \ m )[/tex]

Explanation:

From the question we are told that

     Their distance apart is  [tex]d = 5.00 \ m[/tex]

      The  wavelength of each source wave [tex]\lambda = 6.0 \ m[/tex]

Let the distance from source A  where the construct interference occurred be z

Generally the path difference for constructive interference is

              [tex]z - (d-z) = m \lambda[/tex]

Now given that we are considering just the straight line (i.e  points along the line connecting the two sources ) then the order of the maxima m =  0

  so

        [tex]z - (5-z) = 0[/tex]

=>     [tex]2 z - 5 = 0[/tex]

=>     [tex]z= 2.5 \ m[/tex]

Generally the path difference for destructive  interference is

           [tex]|z-(d-z)| = (2m + 1)\frac{\lambda}{2}[/tex]

=>         [tex]|2z - d |= (0 + 1)\frac{\lambda}{2}[/tex]

=>        [tex]|2z - d| =\frac{\lambda}{2}[/tex]

substituting values

          [tex]|2z - 5| =\frac{6}{2}[/tex]

=>      [tex]z = \frac{5 \pm 3}{2}[/tex]

So  

      [tex]z = \frac{5 + 3}{2}[/tex]

      [tex]z = 4\ m[/tex]

and

      [tex]z = \frac{ 5 -3 }{2}[/tex]

=>   [tex]z = 1 \ m[/tex]

=>    [tex]z = (1 \ m , 4 \ m )[/tex]

PLEASE HELP WILL GIVE BRAINLIEST In an experiment, the hypothesis is that if leaf color is related to temperature, then exposing the plant to low temperatures will result in a leaf color change . This hypothesis is _____. 1. testable 2.falsifiable 3.a and b above 4.none of the above

Answers

Answer:

testable

Explanation:

high heat can cause browning and or welting

Answer:

A

Explanation:

If it is tested, it will really changed when the plant into low temperature

Which of the following statements is true vibrations ?

Answers

Answer:

C. Neither ultrasonic nor infrasonic vibrations can be heard by humans.

Explanation:

The complete question is

Which of the following statements is true of vibrations? A. The frequency of infrasonic vibrations is much too high to be heard by humans. B. Ultrasonic vibrations have a frequency lower than the range for normal hearing. C. Neither ultrasonic nor infrasonic vibrations can be heard by humans. D. Infrasonic vibrations are used in sonar equipment and to detect flaws in steel castings.

Ultrasonic vibrations have frequencies higher than our range of hearing, while infrasonic vibrations have frequencies lower than our range of hearing. Ultrasonic vibrations or sound is used in sonar equipment, and is used for detecting hidden flaws in steel castings and structures. Both infrasonic and ultrasonic fall below and above our normal hearing range respectively, and are only audible to dogs, cats, and some other mammals.

Answer:

Answer is " Two bodies with the same vibration frequency that are placed next to each other will exhibit sympathetic vibrations as one body causes the other to vibrate."

Explanation:

My options were:

A)  Forced vibrations, such as those between a tuning fork and a large cabinet surface, result in a much lower sound than was produced by the original vibrating body.

B)  Resonance occurs as a result of sympathetic vibrations.

C)  A non-vibrating object can begin to vibrate as a result of forced vibrations.

D)  Two bodies with the same vibration frequency that are placed next to each other will exhibit sympathetic vibrations as one body causes the other to vibrate.

A is correct

.

light bulb is connected to a 110-V source. What is the resistance of this bulb if it is a 100-W bulb

Answers

Answer:

121ohms

Explanation:

Formula used for calculating power P = current * voltage

P = IV

From ohms law, V = IR where R is the resistance. Substituting V = IR into the formula for calculating power, we will have;

P = IV

P =(V/R)V

P = V²/R

Given parameters

Power rating of the bulb P = 100 Watts

Source voltage V = 110V

Required

Resistance of the bulb R

Substituting the given parameters into the formula for calculating power to get Resistance R;

P = V²/R

100 = 110²/R

R = 110²/100

R = 110 * 110/100

R = 12100/100

R = 121 ohms

Hence, the resistance of this bulb is 121 ohms

A resistance heater having 20.7 kW power is used to heat a room having 16 m X 16.5 m X 12.3 m size from 13.5 to 21 oC at sea level. The room is sealed once the heater is turned on. Calculate the amount of time needed for this heating to occur in min. (Write your answer in 3 significant digits. Assume constant specific heats at room temperature.)

Answers

Answer:

t = 23.6 min

Explanation:

First we need to find the mass of air in the room:

m = ρV

where,

m = mass of air in the room = ?

ρ = density of air at room temperature = 1.2041 kg/m³

V = Volume of room = 16 m x 16.5 m x 12.3 m = 3247.2 m³

Therefore,

m = (1.2041 kg/m³)(3247.2 m³)

m = 3909.95 kg

Now, we find the amount of energy consumed to heat the room:

E = m C ΔT

where,

E = Energy consumed = ?

C = Specific Heat of air at room temperature = 1 KJ/kg.⁰C

ΔT = Change in temperature = 21 °C - 13.5 °C = 7.5 °C

Therefore,

E = (3909.95 kg)(1 KJ/kg.°C)(7.5 °C)

E = 29324.62 KJ

Now, the time period can be calculated as:

P = E/t

t = E/P

where,

t = Time needed = ?

P = Power of heater = 20.7 KW

Therefore,

t = 29324.62 KJ/20.7 KW

t = (1416.65 s)(1 min/60 s)

t = 23.6 min

A mass M slides downward along a rough plane surface inclined at angle \Theta\:Θ= 32.51 in degrees relative to the horizontal. Initially the mass has a speed V_0\:V 0 = 6.03 m/s, before it slides a distance L = 1.0 m down the incline. During this sliding, the magnitude of the power associated with the work done by friction is equal to the magnitude of the power associated with the work done by the gravitational force. What is the coefficient of kinetic friction between the mass and the incline?

Answers

Answer: μ = 0.8885

Explanation: Force due to friction is calculated as: [tex]F_{f} = \mu.N[/tex]

At an inclined plane, normal force (N) is: N = mgcosθ, in which θ=32.51.

Power associated with work done by friction is [tex]P=F_{f}.x[/tex]. The variable x is displacement the object "spent its energy".

Power associated with work done by gravitational force is P = mghcosθ, where h is height.

The decline forms with horizontal plane a triangle as draw in the picture.

To determine force due to friction:

[tex]F_{f}.x=mghcos(\theta)[/tex]

[tex]F_{f}=\frac{mghcos(\theta)}{x}[/tex]

Replacing force:

[tex]\frac{m.g.h.cos(\theta)}{x} = \mu.m.g.cos(\theta)[/tex]

[tex]\mu=\frac{h}{x}[/tex]

Calculating h using trigonometric relations:

[tex]sin(32.51) = \frac{h}{1}[/tex]

h = sin(32.51)

Coefficient of Kinetic friction is

[tex]\mu=\frac{sin(32.51)}{1}[/tex]

μ = 0.8885

For these conditions, coefficient of kinetic friction is μ = 0.8885.

Did the kinetic frictional coefficient (for the wood/aluminum and felt/aluminum cases) vary with area of contact

Answers

Answer:

Explanation:

Friction is defined as a force which acts at the surface of separation between two objects in contact and tends to oppose motion of one over the other.

While kinetic friction is the force that must be overcome so that a body can move with uniform speed over another.

Hence let consider one of the laws of friction which states that: '' Frictional force is independent of the area of the surfaces in contact.''

The value did not vary with area. This is because when calculating the kinetic fiction, the total contact area is not relevant and only the total weight of the system as well of as the block is put into consideration.

The electric field 2.8 cm from a small object points toward the object with a strength of 180,000 N/C. What is the object's charge?

Answers

Answer:

2.1×10¹⁸ C

Explanation:

Using,

E = kq/r²...................... Equation 1

Where E = Electric field, q = charge, r = distance, k = coulombs constant.

make q the subject of the equation

q = Er²/k.................. Equation 2

Given: E = 180000 N/C, r = 2.8 cm = 0.028 m

Constant: k = 9×10⁹ Nm²/C².

Substitute these values into equation 2

q = 180000(9×10⁹)/0.028²

q = 2.1×10¹⁸ C

Hence the object charge is 2.1×10¹⁸ C

1. Suppose that a solid ball, a solid disk, and a hoop all have the same mass and the same radius. Each object is set rolling without slipping up an incline with the same initial linear (translational) speed. Which goes farthest up
the incline?
a. the ball
b. the disk
c. the hoop
d. the hoop and the disk roll to the same height, farther
than the ball
e. they all roll to the same height
2. Suppose that a solid ball, a solid disk, and a hoop all have the same mass and the same radius. Each object is set rolling with slipping up an incline with the same initial linear (translational) speed. Which goes farthest up
the incline?
a. the ball
b. the disk
c. the hoop
d. the hoop and the disk roll to the same height, farther
than the ball
e. they all roll to the same height

Answers

Answer:

The hoop

Explanation:

Because it has a smaller calculated inertia of 2/3mr² compares to the disc

Which is one criterion that materials of a technological design should meet? They must be imported. They must be affordable. They must be naturally made. They must be locally produced.

Answers

Answer:

they must be affordable because they have to pay for it or they wont get the stuff they are bying.

Explanation:

need a brainliest please.

Answer: B, they must be affordable.

Explanation:

The law of reflection is quite useful for mirrors and other flat, shiny surfaces. (This sort of reflection is called specular reflection). However, you've likely been told that when you look at something, you are seeing light reflected from the object that you are looking at. This is reflection of a different sort of diffuse reflection.

Suppose that the spotlight shines so that different parts of the beam reflect off of different two surfaces, one inclined at an angle alpha (from the horizontal) and one inclined at an angle beta. What would the angular separation between the rays reflected from the two surfaces?

Answers

Answer:

Explanation:

Suppose initially the plane was horizontal and light was reflected back at some angle θ from the normal .

Now the reflecting surface is twisted so that is becomes inclined at angle alpha .

The reflected light will be deviated from its original direction by angle

2 x alpha .

Similarly when the reflecting surface is further twisted so that it becomes inclined at angle beta then again the reflected beam will deviated by angle

2 x beta

Hence angle between these two reflected beam

= 2 beta - 2 alpha

= 2 ( β - α )

So, angular separation between the rays reflected from the two surfaces

= 2 ( β - α ) .

A student wants to create a 6.0V DC battery from a 1.5V DC battery. Can this be done using a transformer alone

Answers

Answer:

Therefore, we need an invert, and a rectifier, along with the transformer to do the job.

Explanation:

A transformer, alone, can not be used to convert a DC voltage to another DC voltage. If we apply a DC voltage to the primary coil of the transformer, it will act as short circuit due to low resistance. It will cause overflow of current through winding, resulting in overheating pf the transformer.

Hence, the transformer only take AC voltage as an input, and converts it to another AC voltage. So, the output voltage of a transformer is also AC voltage.

So, in order to convert a 6 V DC to 1.5 V DC we need an inverter to convert 6 V DC to AC, then a step down transformer to convert it to 1.5 V AC, and finally a rectifier to convert 1.5 V AC to 1.5 V DC.

Therefore, we need an invert, and a rectifier, along with the transformer to do the job.

Other Questions
Find the radius of the circle with equation x^2 + y^2 - 10x - 16y + 53 = 0. Assume that investors have recently become more risk averse, so the market risk premium has increased. Also, assume that the risk-free rate and expected inflation have not changed. Which of the following is most likely to occur?a. The required rate of return will decline for stocks whose betas are less than 1.0 b. The required rate of return on the market, rm, will not change as a result of these changes c. The required rate of return for each individual stock in the market will increase by an amount equal to the increase in the market risk d. The required rate of return on a riskless bond will decline. e. The required rate of return for an average stock will increase by an amount equal to the increase in the market risk premium. Vladimir builds 3 legged stools and 4 legged tables. Last month he used 72 legs to build 3 more stools than tables. How many stools and how many tables did he build? What is conjunctivitis Nancy, aged 70, has a vacant plot adjacent to her house that she intends to bequeath to her grandson Roy upon her death. However, an important railroad project is being undertaken nearby and the local authorities have informed Nancy that the new railroad will cover her vacant lot. They have also promised her fair compensation in return. Can the government take her property? The maximum gauge pressure in a hydraulic system is 15 atm. What is the largest mass that could be lifted by this system if the diameter of the piston is 65 cm AB=a just incase it cant be seen In a triangle ABC,AB=9 and BC =12 which of the following Cannot be the length of AC. The common stock of Eddie's Engines, Inc., sells for $37.13 a share. The stock is expected to pay a dividend of $3.10 per share next year. Eddie's has established a pattern of increasing their dividends by 5.2 percent annually and expects to continue doing so. What is the market rate of return on this stock? Explain your reasoning. Match each explanation to the appropriate blanks in the sentences on the right. 1. the atomic radius decreases 2. the number of gas molecules decreases 3. molar mass and structure complexity decreases 4. structure complexity decreases 5. molar mass decreases 6. each phase (gas, liquid, solid) becomes more ordered A (I_2(g), Br_2 (g), Cl_2 (g), F_2 (B): The ranking can best be explained by the trend entropy decreases as______. B (H_2O_2 (g), H_2S(g), H_2O(g): The ranking can best be explained by the decreases a trend entropy decreases as_______. C. (C(s, amorphous), C(s, graphite), C(s, diamond): The ranking can best be explained by the trend entropy decreases as_______. find the empirical formula of the compound containing 11.3% of carbon, 43.4 % of sodium 45.3 % of oxygen What happens to the rate of dissolution as the temperature is increased in a gas solution?A. The rate stays the same.B. The rate decreases.C. The rate increases.D. There is no way to tell. You cross a plant with red flowers with a plant with white flowers. Both plants are pure-breeding. All the offspring have pink flowers. What allele relationship does this display? codominance multiple alleles incomplete dominance pleiotropy ANYONE PLEASE HEEEEEEELLLLLLLPPPPPP!!!!! WILL GIVE BRAINLIEST!!!Question 4(Multiple Choice Worth 1 points) (06.04 LC) Choose the correct simplification of the expression 3x2(5x 4x2 6). 7x4 + 2x3 9x2 12x4 15x3 + 18x2 12x4 + 15x3 + 18x2 12x4 + 15x3 18x2 Please explain and help The function f is defined by f(x) = (x + 3)(x + 1).The graph of f in the xy-plane is a parabola. Whichof the following intervals contains the x-coordinateof the vertex of the graph of f? Simplify (3c3w5)3. 9c6w8 9c9w15 27c6w8 27c9w15 In the BCG Growth Share Matrix, the suggested strategy for Stars is to ________. A. milk them to finance other businesses B. invest large sums to gain a good market share C. maintain position and after the market growth slows use the business to provide cash flow D. not invest in them and to shift cash flow to other businesses A car enters a turnpike 22 miles north of a town. The car teavels north at an average speed of 64 miles per hour. How far is the car from the town after 4 hours? Explain how you can use linear function to solve this problem. Then, solve the problem. Write the phrase as an expression. Then evaluate the expression when x = 5.6 more than the product of 8 and a number xExpression:When x = 5, the value of the expression is