Answer:
you are going to expend energy to give a lot of velocity (and momentum) to your foot in order to transfer it the stone air drag this time the kicking speed is for superior to walking speed.
Thank You
Open the sash half way up, take the beaker containing the dry ice / water out of the hood, and slowly move it from right in front of the hood all the way down to the floor. At what point do the fumes stop getting sucked up by the fume hood?
Answer:
The fumes stop getting sucked up by the fume hood once the beaker is pulled out of the hood.
If a jet travels 350 m/s, how far will it travel each second?
Answer:
350
Explanation:
Since it travels 350 meters per second, the jet will travel 350 meters in one second.
calculate the length of wire.
Answer:
L = 169.5 m
Explanation:
Using Ohm's Law:
V = IR
where,
V = Voltage = 1.5 V
I = Current = 10 mA = 0.01 A
R = Resistance = ?
Therefore,
1.5 V = (0.01 A)R
R = 150 Ω
But the resistance of a wire is given by the following formula:
[tex]R = \frac{\rho L}{A}[/tex]
where,
ρ = resistivity = 1 x 10⁻⁶ Ω.m
L = length of wire = ?
A = cross-sectional area of wire = πr² = π(0.6 mm)² = π(0.6 x 10⁻³ m)²
A = 1.13 x 10⁻⁶ m²
Therefore,
[tex]150\ \Omega = \frac{(1\ x\ 10^{-6}\ \Omega .m)L}{1.13\ x\ 10^{-6}\ m^2}\\\\L = \frac{150\ \Omega(1.13\ x\ 10^{-6}\ m^2)}{1\ x\ 10^{-6}\ \Omega .m}\\\\[/tex]
L = 169.5 m
A block of mass 2 kg is launched by compressing a spring of force constant 1200 N/m. The block slides on a frictionless surface, up a 1 meter tall ramp, then it enters a region of rough surface. It comes to a stop after traveling 3 meters over the rough surface. The coefficient of kinetic friction between the block and the rough surface is 0.40.
Required:
a. How many forces end up doing work on the block from release to stop?
b. What is the total non-conservative work done on the block?
c. What is the change in the spring potential energy of the block?
Answer:
zzyibgsdwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwwe
Explanation:
What type of wave is a microwave?
O heat
O longitudinal
sound
transverse
Answer:
Microwave is a types of a electromagnetic radiation
Answer:
Transvers
Explanation:
Because microwave is electromagnetic waves and all electromagnetic waves are transvers.
how can you relazie a perfect balck body in pratice
Suppose a 60-turn coil lies in the plane of the page in a uniform magnetic field that is directed out of the page. The coil originally has an area of 0.325 m2. It is stretched to have no area in 0.100 s. What is the magnitude (in V) and direction (as seen from above) of the average induced emf if the uniform magnetic field has a strength of 1.60 T
Answer:
emf = 312 V
Explanation:
In this exercise the electromotive force is asked, for which we must use Faraday's law
emf = [tex]- N \frac{d \Phi }{dt}[/tex]- N dfi / dt
Ф = B. A = B A cos θ
bold type indicates vectors.
They indicate that the magnetic field is constant, the angle between the normal to the area and the magnetic field is parallel by local cosine values 1
It also indicates that the area is reduced from a₀ = 0.325 me² to a_f = 0 in a time interval of ΔT = 0.100 s, suppose that this reduction is linear
emf = -N B [tex]\frac{dA}{dT}[/tex]
emf = - N B (A_f - A₀) / Dt
we calculate
emf = - 60 1.60 (0 - 0.325) /0.100
emf = 312 V
The direction of this voltage is exiting the page
An astronaut on the moon drops a rock from rest. The rock falls 0.8m in one second of falling time. If the dropped rock fell for a total of two seconds of time instead of 1 second, then the distance traveled would be:____.
A) The same.
B) Doubled.
C) Tripled.
D) Quadruple.
E) None of the above.
Answer:
D) Quadruple.
Explanation:
We will use the second equation of motion to solve this problem:
[tex]s = v_it + \frac{1}{2}gt^2[/tex]
where,
s = distance travelled by the rock
vi = initial speed of rock = 0 m/s
t = time taken
g = acceleration due to gravity on the surface of the moon
Therefore,
[tex]s = (0\ m/s)t+\frac{1}{2}gt^2\\\\s =\frac{1}{2}gt^2[/tex]----------- equation (1)
Now, we double the time:
[tex]s' = \frac{1}{2}g(2t)^2\\\\s' = 4(\frac{1}{2}gt^2)[/tex]
using equation (1):
s' = 4s
Hence, the correct option is:
D) Quadruple.
I’m a photoelectric effect, which property of the incident light determines how much kinetic energy the ejected electrons have ?
A) brightness
B) frequency
C) size of the beam
D) none of the above
Answer:
b = frequency
A 500 kg rocket sled is coasting in reverse at 10 m/s (to the left). It then turns on its rocket engines for 10.0 s, with a thrust of 1500 N (to the right). What is its final velocity? (Remember velocity has magnitude and direction)
Explanation:
F = ma
[tex]a = \frac{f}{m} [/tex]
[tex]a = \frac{1500}{500} = 3[/tex]
[tex]a = \frac{v2 - v1}{t} [/tex]
[tex]3 = \frac{v2 - 10}{10} [/tex]
v2 (final) = 40 m/s to the right direction
A friend lends you the eyepiece of his microscope to use on your own microscope. He claims that since his eyepiece has the same diameter as yours but twice the focal length, the resolving power of your microscope will be doubled. Is his claim valid? Explain.
Answer:
The resolving power remains same.
Explanation:
The resolving power of the lens is directly proportional to the diameter of the lens not on the focal length.
As the diameter is same but the focal length is doubled so the resolving power remains same.
Explain how blood circulation takes place in humans?
Blood comes into the right atrium from the body, moves into the right ventricle and is pushed into the pulmonary arteries in the lungs. After picking up oxygen, the blood travels back to the heart through the pulmonary veins into the left atrium, to the left ventricle and out to the body's tissues through the aorta.
Hope it helps you
Mark my answer as brainlist
have a nice day
A positron is a particle that has the same mass but opposite charge of an electron. An electron and a positron are shot directly toward each other by a particle accelerator. They start very far from each other, each with a kinetic energy of
Complete Question
The Complete Question is Attached below
Answer:
[tex]E_t=2.14*10^{-13}J[/tex]
Explanation:
From the question we are told that:
Kinetic energy [tex]K.E=5*10^{-14}[/tex]
Generally, the equation for Total Energy is mathematically given by
[tex]E_t=K.E+2me[/tex]
Where
Mass of an electron in MeV
[tex]m=0.510 998 950 00 MeV[/tex]
And
Electron Charge
[tex]1.6 * 10^{-19}[/tex]
Therefore
[tex]E_t=K.E+2me[/tex]
[tex]E_t=5*10^{-14}*0.510 998 950 00*1.6 * 10^{-19}[/tex]
[tex]E_t=2.14*10^{-13}J[/tex]
A capacitor consists of two parallel conducting plates, each of area 0.4 m2 and separated by a distance of 2.0 cm. Assume there is air between the plates. While connected to a battery the electric field within the plates is 500 N/C. The potential difference between the plates is: ________
a) 5.0 V
b) 10 V
c) 30 V
d) 20 V
Answer:
check photo
Explanation:
The cation that is reabsorbed from the urine in response to aldosterone
Answer:
If decreased blood pressure is detected, the adrenal gland is stimulated by these stretch receptors to release aldosterone, which increases sodium reabsorption from the urine, sweat, and the gut. This causes increased osmolarity in the extracellular fluid, which will eventually return blood pressure toward normal.
5. Steve is driving in his car to take care of some errands. The first errand has him driving to a location 2 km East and 6 km North of his starting location. Once he completes that errand, he drives to the second one which is 4 km East and 2 km South of the first errand. What is the magnitude of the vector that describes how far the car has traveled from its starting point, rounded to the nearest km?
Answer:
gshshs
Explanation:
hshsksksksbsbbshd
list at least types of motion
Answer:
These four are rotary, oscillating, linear and reciprocating. Each one moves in a slightly different way and each type of achieved using different mechanical means that help us understand linear motion and motion control.
(I got this off the web so credits to the rightful owner and I hope you have good day :)
A 1.5kg block slides along a frictionless surface at 1.3m/s . A second block, sliding at a faster 4.3m/s , collides with the first from behind and sticks to it. The final velocity of the combined blocks is 2.0m/s . What was the mass of the second block?
Answer:
The mass of the second block=0.457 kg
Explanation:
We are given that
m1=1.5 kg
v1=1.3m/s
v2=4.3 m/s
V=2.0 m/s
We have to find the mass of the second block.
[tex]m_1v_1+m_2v_2=(m_1+m_2)V[/tex]
Let m2=m
Substitute the values
[tex]1.5(1.3)+m(4.3)=(1.5+m)(2)[/tex]
[tex]1.95+4.3m=3+2m[/tex]
[tex]4.3m-2m=3-1.95[/tex]
[tex]2.3m=1.05[/tex]
[tex]m=\frac{1.05}{2.3}[/tex]
[tex]m=0.457 kg[/tex]
Hence, the mass of the second block=0.457 kg
what is liquid pressure and its si unit?
The SI unit of pressure is the pascal: 1Pa=1N/m2 1 Pa = 1 N/m 2 . Pressure due to the weight of a liquid of constant density is given by p=ρgh p = ρ g h , where p is the pressure, h is the depth of the liquid, ρ is the density of the liquid, and g is the acceleration due to gravity.
Why is it advised not to hold the thermometer by its bulb while reading it?
if you jog at a speed of 1.5m/s for 20 seconds how far di you travel
Answer: 30m
Explanation:
Given:
Speed: 1.5m/s
Time: 20 seconds
Distance = speed × time
Distance = 1.5 × 20
= 30m
Therefore you will travel 30m
Must click thanks and mark brainliest
physics approach to study macromoelcues at nanoscales
in detail plx
Answer:
Abstracto
Los ácidos nucleicos y las proteínas comprenden una red de biomacromoléculas que almacenan y transmiten información que sustenta la vida de la célula. El estudio de estos mecanismos es un campo llamado biología molecular. El desarrollo de esta ciencia siempre ha ido acompañado de avances técnicos que permiten romper barreras metodológicas para probar hipótesis novedosas. Entre los métodos disponibles para los biólogos moleculares, destacan cinco: electroforesis, secuenciación, clonación, transferencia y reacción en cadena de la polimerasa. Su impacto llega a la genética, la medicina y la biotecnología. Aquí, se revisan la relevancia histórica, los fundamentos técnicos y las tendencias actuales de estos cinco métodos esenciales. La revisión pretende ser útil tanto para estudiantes como para científicos profesionales que buscan adquirir conocimientos avanzados sobre el valor de estos métodos para investigar los mecanismos moleculares que sostienen la vida.
. A ball of mass 0.50 kg is rolling across a table top with a speed of 5.0 m/s. When the ball reaches the edge of the table, it rolls down an incline onto the floor 1.0 meter below (without bouncing). What is the speed of the ball when it reaches the floor?
Answer:
4
Explanation:
Which factor affects kinetic energy but not potential energy?
Answer:
mass
Explanation:
because as the mass increase kinetic energy also increase
A simple pendulum consists of a ball of mass 3 kg hanging from a uniform string of mass 0.05 kg and length L. If the period of oscillation of the pendulum is 2 s, determine the speed of a transverse wave in the string when the pendulum hangs vertically.
Answer:
v = 3.12 m/s
Explanation:
First, we will find the length of the string by using the formula of the time period:
[tex]T = 2\pi \sqrt{\frac{l}{g}}\\\\l = \frac{T^2g}{4\pi^2}\\\\[/tex]
where,
l = length of string = ?
T = time period = 2 s
g = acceleration due to gravity = 9.81 m/s²
Therefore,
[tex]l = \frac{(2\ s)^2(9.81\ m/s^2)}{4\pi^2}\\\\l = 0.99\ m[/tex]
Now, we will find tension in the string in the vertical position through the weight of the ball:
T = W = mg = (3 kg)(9.81 m/s²)
T = 29.43 N
Now, the speed of the transverse wave is given as follows:
[tex]v=\sqrt{\frac{Tl}{m}}\\\\v=\sqrt{\frac{(29.43\ N)(0.99\ m)}{3\ kg}}\\\\[/tex]
v = 3.12 m/s
Rachel has good distant vision but has a touch of presbyopia. Her near point is 0.60 m. Part A When she wears 2.0 D reading glasses, what is her near point
Answer:
The right answer is "0.273 m".
Explanation:
Given:
Power (P),
[tex]\frac{1}{f} = 2D[/tex]
Near point,
u = 0.6 m
As we know,
⇒ [tex]\frac{1}{v} -\frac{1}{u}=\frac{1}{f} = 2[/tex]
By substituting the values, we get
⇒ [tex]\frac{1}{v} -\frac{1}{0.6} =2[/tex]
[tex]\frac{1}{v}=2+\frac{1}{0.6}[/tex]
[tex]\frac{1}{v} =\frac{1.2+1}{0.6}[/tex]
[tex]\frac{1}{v}=\frac{2.2}{0.6}[/tex]
By applying cross-multiplication, we get
[tex]0.6=2.2 \ v[/tex]
[tex]v = \frac{0.6}{2.2}[/tex]
[tex]S_{near} = 0.273 \ m[/tex]
b. Projectile on cliff (range)
An object of mass 5 kg is projected at an angle of 25° to the horizontal with a speed of 22 ms-1 from the top of the cliff.
The height of the cliff is 21 m. Take g, the acceleration due to gravity, to be 9.81 ms2
How far horizontally (to 1 decimal place) from the base of the cliff does the object land?
Answer:
x = 41.28 m
Explanation:
This is a projectile launching exercise, let's find the time it takes to get to the base of the cliff.
Let's start by using trigonometry to find the initial velocity
cos 25 = v₀ₓ / v₀
sin 25 = Iv_{oy} / v₀
v₀ₓ = v₀ cos 25
v_{oy} = v₀ sin 25
v₀ₓ = 22 cos 25 = 19.94 m / s
v_{oy} = 22 sin 25 = 0.0192 m / s
let's use movement on the vertical axis
y = y₀ + v_{oy} t - ½ g t²
when reaching the base of the cliff y = 0 and the initial height is y₀ = 21 m
0 = 21 + 0.0192 t - ½ 9.81 t²
4.905 t² - 0.0192 t - 21 = 0
t² - 0.003914 t - 4.2813 =0
we solve the quadratic equation
t = [tex]\frac{ 0.003914\ \pm \sqrt{0.003914^2 + 4 \ 4.2813 } }{2}[/tex]
t = [tex]\frac{0.003914 \ \pm 4.13828}{2}[/tex]
t₁ = 2.07 s
t₂ = -2.067 s
since time must be a positive scalar quantity, the correct result is
t = 2.07 s
now we can look up the distance traveled
x = v₀ₓ t
x = 19.94 2.07
x = 41.28 m
The pressure of sea water increases by 1.0atm for each 10m increase in the depth, by what percentage is the density of water increased in the deepest ocean of water of 12km. Compressibility is 5.0×10^-5 atm
The percentage by which the water density increased is 4.1[tex]\mathbf{\overline 6}[/tex] %
The known values are;
The increase in pressure per 10 meter increase in depth = 1.0 atm
The depth of the deepest ocean = 12 km = 12,000 m
The compressibility of the ocean = 5.0 × 10⁻⁵ 1/atm
The unknown
The percentage the density of water increased in the deepest ocean
Strategy;
Find the pressure at the deepest point of the deepest ocean and apply the compressibility
We have;
[tex]\mathbf{Compressibility = \dfrac{1}{V} \times \dfrac{\partial V}{\partial p}}[/tex]
The change in pressure, [tex]\partial p[/tex] = (12,000 m/(10 m)) × 1.0 atm = 1,200 atm
Therefore, we have for one cubic meter of water
[tex]\mathbf{5.0 \times 10^{-5} \ atm^{-1} = \dfrac{1}{1 \, m^3} \times \dfrac{\partial V}{1,200 \, atm}}[/tex]
Therefore;
[tex]\mathbf{\partial}[/tex]V = 5.0 × 10⁻⁵ atm⁻¹ × 1 m³ × 1,200 atm = 0.06 m³
The new volume = V - [tex]\mathbf{\partial}[/tex]V
∴ The new volume = 1 m³ - 0.06 m³ = 0.94 m³
The initial density = mass/(1 m³)
The new density = mass/(0.96 m³)
The percentage increase in density, [tex]\partial[/tex]ρ%, is given as follows;
[tex]\mathbf{\partial p \% = \dfrac{ \dfrac{Mass}{0.96 \ m^3} - \dfrac{Mass}{1 \ m^3} }{ \dfrac{Mass}{1 \ m^3}} \times 100 = \dfrac{25}{6} \% = 4.1 \overline 6 \%}[/tex]
∴ [tex]\mathbf{\partial}[/tex]ρ% = 4.1[tex]\mathbf {\overline 6}[/tex] %
The percentage by which the water density increased, [tex]\partial[/tex]ρ% = 4.1[tex]\mathbf{\overline 6}[/tex] %
Learn more about compressibility here;
https://brainly.com/question/18746977
why the stone moves away when the string is broken rotation
Answer:
When a stone is going around a circular path, the instantaneous velocity of stone is acting as tangent to the circle. When the string breaks, the centripetal force stops to act. Due to inertia, the stone continues to move along the tangent to circular path. So, the stone flies off tangentially to the circular path
Answer:
when the string's rotation is broken, there will be no centripetal force to keep the stone stationary. Thus, the stone will flung away when the rotation is stopped
The coefficients of friction between a race cars tyres and the track surface are
the question is about tyres of a race car, which are made of rubber and will be in contact with a race track, which is generally made from asphalt, the static coefficient of friction is in the range of (0.5–0.8), in dry conditions (Source: Friction and Friction Coefficients ).
Explanation:
please mark me as a brainlieast
