A certain car traveling 33.0mph skids to a stop in 39m from the point where the brakes were applied. In approximately what distance would the car stop had it been going 66.0mph

Answers

Answer 1

Answer: 156.02 metre.

Explanation:

Give that a certain car traveling 33.0mph skids to a stop in 39m from the point where the brakes were applied.

Let us use third equation of motion,

V^2 = U^2 + 2as

Since the car is decelerating, V = 0

And acceleration a will be negative.

U = 33 mph

S = 39 m

Substitute both into the formula

0 = 33^2 - 2 × a × 39

0 = 1089 - 78a

78a = 1089

a = 1089 / 78

a = 13.96 m/h^2

If we assume that the car decelerate at the same rate.

the distance the car will stop had it been going 66.0mph will be achieved by using the same formula

V^2 = U^2 + 2as

0 = 66^2 - 2 × 13.96 × S

4356 = 27.92S

S = 4356 / 27.92

S = 156.02 m

Therefore, the car would stop at

156.02 m


Related Questions

A cook preparing a meal for a group of people is an example of
O kinetic energy because he has the ability to make a meal
O potential energy because he has the ability to make a meal
O kinetic energy because he is making the meal
o potential energy because he is making the meal​

Answers

The third point is the correct answer because it’s happening now and kinetic energy is energy possessed by a moving object.

Hope this helps ya

A circular loop in the plane of a paper lies in a 0.45 T magnetic field pointing into the paper. The loop's diameter changes from 17.0 cm to 6.0 cm in 0.53 s.
A) Determine the direction of the induced current.
B) Determine the magnitude of the average induced emf.
C) If the coil resistance is 2.5 Ω, what is the average induced current?

Answers

Answer:

(A). The direction of the induced current will be clockwise.

(B). The magnitude of the average induced emf 16.87 mV.

(C). The induced current is 6.75 mA.

Explanation:

Given that,

Magnetic field = 0.45 T

The loop's diameter changes from 17.0 cm to 6.0 cm .

Time = 0.53 sec

(A). We need to find the direction of the induced current.

Using Lenz law

If the direction of magnetic field shows into the paper then the direction of the induced current will be clockwise.

(B). We need to calculate the magnetic flux

Using formula of flux

[tex]\phi_{1}=BA\cos\theta[/tex]

Put the value into the formula

[tex]\phi_{1}=0.45\times(\pi\times(8.5\times10^{-2})^2)\cos0[/tex]

[tex]\phi_{1}=0.01021\ Wb[/tex]

We need to calculate the magnetic flux

Using formula of flux

[tex]\phi_{2}=BA\cos\theta[/tex]

Put the value into the formula

[tex]\phi_{2}=0.45\times(\pi\times(3\times10^{-2})^2)\cos0[/tex]

[tex]\phi_{2}=0.00127\ Wb[/tex]

We need to calculate the magnitude of the average induced emf

Using formula of emf

[tex]\epsilon=-N(\dfrac{\Delta \phi}{\Delta t})[/tex]

Put the value into t5he formula

[tex]\epsilon=-1\times(\dfrac{0.00127-0.01021}{0.53})[/tex]

[tex]\epsilon=0.016867\ V[/tex]

[tex]\epsilon=16.87\ mV[/tex]

(C). If the coil resistance is 2.5 Ω.

We need to calculate the induced current

Using formula of current

[tex]I=\dfrac{\epsilon}{R}[/tex]

Put the value into the formula

[tex]I=\dfrac{0.016867}{2.5}[/tex]

[tex]I=0.00675\ A[/tex]

[tex]I=6.75\ mA[/tex]

Hence, (A). The direction of the induced current will be clockwise.

(B). The magnitude of the average induced emf 16.87 mV.

(C). The induced current is 6.75 mA.

A diffraction grating 19.2 mm wide has 6010 rulings. Light of wavelength 337 nm is incident perpendicularly on the grating. What are the (a) largest, (b) second largest, and (c) third largest values of θ at which maxima appear on a distant viewing screen?

Answers

Answer:

(a). The largest value of θ is 71.9°.

(b). The second largest value of θ is 57.7°.

(c). The third largest value of θ is 47.7° .

Explanation:

Given that,

Width of diffraction grating [tex]w= 19.2\ mm[/tex]

Number of rulings[tex]N=6010[/tex]

Wavelength = 337 nm

We need to calculate the distance between adjacent rulings

Using formula of distance

[tex]d=\dfrac{w}{N}[/tex]

Put the value into the formula

[tex]d=\dfrac{19.2\times10^{-3}}{6010}[/tex]

[tex]d=3.19\times10^{-6}\ m[/tex]

We need to calculate the value of m

Using formula of constructive interference

[tex]d \sin\theta=m\lambda[/tex]

[tex]\sin\theta=\dfrac{m\lambda}{d}[/tex]

Here, m = 0,1,2,3,4......

[tex]\lambda[/tex]=wavelength

For largest value of  θ

[tex]\dfrac{m\lambda}{d}>1[/tex]

[tex]m>\dfrac{d}{\lambda}[/tex]

Put the value into the formula

[tex]m>\dfrac{3.19\times10^{-6}}{337\times10^{-9}}[/tex]

[tex]m>9.46[/tex]

[tex]m = 9[/tex]

(a). We need to calculate the largest value of θ

Using formula of constructive interference

[tex]\theta=\sin^{-1}(\dfrac{m\lambda}{d})[/tex]

Now, put the value of m in to the formula

[tex]\theta=\sin^{-1}(\dfrac{9\times337\times10^{-9}}{3.19\times10^{-6}})[/tex]

[tex]\theta=71.9^{\circ}[/tex]

(b). We need to calculate the second largest value of θ

Using formula of constructive interference

[tex]\theta=\sin^{-1}(\dfrac{m\lambda}{d})[/tex]

Now, put the value of m in to the formula

[tex]\theta=\sin^{-1}(\dfrac{8\times337\times10^{-9}}{3.19\times10^{-6}})[/tex]

[tex]\theta=57.7^{\circ}[/tex]

(c). We need to calculate the third largest value of θ

Using formula of constructive interference

[tex]\theta=\sin^{-1}(\dfrac{m\lambda}{d})[/tex]

Now, put the value of m in to the formula

[tex]\theta=\sin^{-1}(\dfrac{7\times337\times10^{-9}}{3.19\times10^{-6}})[/tex]

[tex]\theta=47.7^{\circ}[/tex]

Hence, (a). The largest value of θ is 71.9°.

(b). The second largest value of θ is 57.7°.

(c). The third largest value of θ is 47.7° .

A speeding car has a velocity of 80 mph; suddenly it passes a cop car but does not stop. When the speeding car passes the cop car, the cop immediately accelerates his vehicle from 0 to 90 mph in 4.5 seconds. The cop car has a maximum velocity of 90 mph. At what time does the cop car meet the speeding car and at what distance?

Answers

Answer:

Distance= 4 miles

Time = 36.3 seconds

Explanation:

80 mph = 178.95 m/s

90 mph = 201.32 m/s

V = u +at

201.32= 0+a(4.5)

201.32/4.5= a

44.738 m/s² = a

Acceleration of the cop car

= 44.738 m/s²

Distance traveled at 4.5seconds

For the cop car

S= ut + ½at²

S= 0(4.5) + ½*44.738*4.5

S= 100.66 meters

Distance traveled at 4.5seconds

For the speeding car

4.5*178.95=805.275

The cop car will still cover 704.675 +x distance while the speeding car covers for their distance to be equal

X/178.95= (704.675+x)/201.32

X-0.89x= 626.37

0.11x= 626.37

X= 5694.3 meters

The time = 5694.3/178.95

Time =31.8 seconds

So the distance they meet

= 5694.3+805.275

= 6499.575 meters

= 4.0 miles

The Time = 4.5+31.8

Time = 36.3 seconds

a person Travels along a straight road for half the distance with velocity V1 and the remaining half the distance with velocity V2 the average velocity is given by​

Answers

Answer: (V1+V2)/2

Explanation: This is because basically with the question they are trying to say u(initial velocity) is V1 and v(final velocity) is V2 as the journey starts off with V1 and ends with V2 so therefore we know an equation where average velocity=(u+v)/2. So here it’s (V1+V2)/2

In a physics lab, light with a wavelength of 490 nm travels in air from a laser to a photocell in a time of 17.5 ns . When a slab of glass with a thickness of 0.800 m is placed in the light beam, with the beam incident along the normal to the parallel faces of the slab, it takes the light a time of 21.5 ns to travel from the laser to the photocell.What is the wavelength of the light in the glass? Use 3.00×108 m/s for the speed of light in a vacuum. Express your answer using two significant figures.

Answers

Answer:

196 nm

Explanation:

Given that

Value of wavelength, = 490 nm

Time spent in air, t(a) = 17.5 ns

Thickness of glass, th = 0.8 m

Time spent in glass, t(g) = 21.5 ns

Speed of light in a vacuum, c = 3*10^8 m/s

To start with, we find the difference between the two time spent

Time spent on glass - Time spent in air

21.5 - 17.5 = 4 ns

0.8/(c/n) - 0.8/c = 4 ns

Note, light travels with c/n speed in media that has index of refraction

(n - 1) * 0.8/c = 4 ns

n - 1 = (4 ns * c) / 0.8

n - 1 = (4*10^-9 * 3*10^8) / 0.8

n - 1 = 1.2/0.8

n - 1 = 1.5

n = 1.5 + 1

n = 2.5

As a result, the wavelength of light in a medium with index of refraction would then be

490 / 2.5 = 196 nm

Therefore, our answer is 196 nm

When a monochromatic light of wavelength 433 nm incident on a double slit of slit separation 6 µm, there are 5 interference fringes in its central maximum. How many interference fringes will be in the central maximum of a light of wavelength 632.9 nm for the same double slit?

Answers

Answer:

The number of interference fringes is  [tex]n = 3[/tex]

Explanation:

From the question we are told that

     The wavelength is  [tex]\lambda = 433 \ nm = 433 *10^{-9} \ m[/tex]

      The distance of separation is  [tex]d = 6 \mu m = 6 *10^{-6} \ m[/tex]

       The  order of maxima is m =  5

       

The  condition for constructive interference is

       [tex]d sin \theta = n \lambda[/tex]

=>     [tex]\theta = sin^{-1} [\frac{5 * 433 *10^{-9}}{ 6 *10^{-6}} ][/tex]

=>    [tex]\theta = 21.16^o[/tex]

So at  

      [tex]\lambda_1 = 632.9 nm = 632.9*10^{-9} \ m[/tex]

   [tex]6 * 10^{-6} * sin (21.16) = n * 632.9 *10^{-9}[/tex]

=>    [tex]n = 3[/tex]

   

On a separate sheet of paper, tell why scientists in different countries can easily compare the amount of matter in similar objects in their countries

Answers

Answer: no u

Explanation: no u

A student holds a bike wheel and starts it spinning with an initial angular speed of 7.0 rotations per second. The wheel is subject to some friction, so it gradually slows down.

In the 10.0 s period following the inital spin, the bike wheel undergoes 60.0 complete rotations. Assuming the frictional torque remains constant, how much more time Δ????s will it take the bike wheel to come to a complete stop?

The bike wheel has a mass of 0.625 kg0.625 kg and a radius of 0.315 m0.315 m. If all the mass of the wheel is assumed to be located on the rim, find the magnitude of the frictional torque ????fτf that was acting on the spinning wheel.

Answers

Answer:

a)   Δt = 24.96 s , b)  τ = 0.078 N m

Explanation:

This is a rotational kinematics exercise

        θ = w₀ t - ½ α t²

Let's reduce the magnitudes the SI system

       θ = 60 rev (2π rad / 1 rev) = 376.99 rad

       w₀ = 7.0 rot / s (2π rad / 1 rpt) = 43.98 rad / s

       

      α = (w₀ t - θ) 2 / t²

let's calculate the annular acceleration

      α = (43.98 10 - 376.99) 2/10²

      α = 1,258 rad / s²

Let's find the time it takes to reach zero angular velocity (w = 0)

        w = w₀ - alf t

         t = (w₀ - 0) / α

         t = 43.98 / 1.258

         t = 34.96 s

this is the total time, the time remaining is

         Δt = t-10

         Δt = 24.96 s

To find the braking torque, we use Newton's law for angular motion

        τ = I α

the moment of inertia of a circular ring is

       I = M r²

we substitute

         τ = M r² α

we calculate

        τ = 0.625  0.315²  1.258

        τ = 0.078 N m

The total time taken by the wheel to come to rest is 25.18 s and the magnitude of the frictional torque is 25.18 N-m.

Given data:

The initial angular speed of wheel is, [tex]\omega = 7.0 \;\rm rps[/tex]   (rps means rotation per second).

The time interval is, t' = 10.0 s.

The number of rotations made by wheel is, n = 60.0.

The mass of bike wheel is, m = 0.625 kg.

The radius of wheel is, r = 0.315 m.

The problem is based on rotational kinematics. So, apply the second rotational equation of motion as,

[tex]\theta = \omega t-\dfrac{1}{2} \alpha t'^{2}[/tex]

Here, [tex]\theta[/tex] is the angular displacement, and its value is,

[tex]\theta =2\pi \times 60\\\\\theta = 376.99 \;\rm rad[/tex]

And, angular speed is,

[tex]\omega = 2\pi n\\\omega = 2\pi \times 7\\\omega = 43.98 \;\rm rad/s[/tex]

Solving as,

[tex]376.99 = 43.98 \times 10-\dfrac{1}{2} \alpha \times 10^{2}\\\\\alpha = 1.25 \;\rm rad/s^{2}[/tex]

Apply the first rotational equation of motion to obtain the value of time to reach zero final velocity.

[tex]\omega' = \omega - \alpha t\\\\0 = 43.98 - 1.25 \times t\\\\t = 35.18 \;\rm s[/tex]

Then total time is,

T = t - t'

T = 35.18 - 10

T = 25.18 s

Now, use the standard formula to obtain the value of braking torque as,

[tex]T = m r^{2} \alpha\\\\T = 0.625 \times (0.315)^{2} \times 1.25\\\\T = 0.0775 \;\rm Nm[/tex]

Thus, we can conclude that the total time taken by the wheel to come to rest is 25.18 s and the magnitude of the frictional torque is 25.18 N-m.

Learn more about the rotational motion here:

https://brainly.com/question/1388042

A jumbo jet has a mass of 100,000 kg. The thrust of each of its four engines is 50,000 N. What is the jet's acceleration in meters per second squared right before taking off? Neglect air resistance and friction.

Answers

Answer:

The acceleration is   [tex]a =2\ m/s^2[/tex]

Explanation:

From the question we are told that

       The  mass of the jumbo jet is  [tex]m_j = 100000\ kg[/tex]

        The thrust is  [tex]F_k = 50000 \ N[/tex]

Generally given that the jet has four engines the total thrust is  

        [tex]F_t = 4 * F_k[/tex]

substituting values

       [tex]F_t = 4 * 50000[/tex]

      [tex]F_t = 200000 \ N[/tex]

Generally the acceleration of the is mathematically represented as

         [tex]a = \frac{F_t}{m}[/tex]

substituting values

       [tex]a =2 \frac{N}{kg}[/tex]

Now  

        [tex]N = kg \cdot m/s^2[/tex]

Hence

         [tex]a =2 \frac{kg * \cdot m/s^2}{kg}[/tex]

        [tex]a =2\ m/s^2[/tex]

W is the work done on the system, and K, U, and Eth are the kinetic, potential, and thermal energies of the system, respectively. Any energy not mentioned in the transformation is assumed to remain constant; if work is not mentioned, it is assumed to be zero.

1. Give a specific example of a system with the energy transformation shown.
W→ΔEth

2. Give a specific example of a system with the energy transformation shown.

a. Rolling a ball up a hill.
b. Moving a block of wood across a horizontal rough surface at constant speed.
c. A block sliding on level ground, to which a cord you are holding on to is attached .
d. Dropping a ball from a height.

Answers

Answer:

1) a block going down a slope

2) a) W = ΔU + ΔK + ΔE, b) W = ΔE, c)  W = ΔK, d) ΔU = ΔK

Explanation:

In this exercise you are asked to give an example of various types of systems

1) a system where work is transformed into internal energy is a system with friction, for example a block going down a slope in this case work is done during the descent, which is transformed in part kinetic energy, in part power energy and partly internal energy that is represented by an increase in the temperature of the block.

2)

a) rolling a ball uphill

In this case we have an increase in potential energy, if there is a change in speed, the kinetic energy also increases, if the change in speed is zero, there is no change in kinetic energy and there is a change in internal energy due to the stationary rec in the point of contact

 W = ΔU + ΔK + ΔE

b) in this system work is transformed into internal energy

      W = ΔE

c) There is no friction here, therefore the work is transformed into kinetic energy

    W = ΔK

d) if you assume that there is no friction with the air, the potential energy is transformed into kinetic energy

      ΔU = ΔK

There are 5510 lines per centimeter in a grating that is used with light whose wavelegth is 467 nm. A flat observation screen is located 1.03 m from the grating. What is the minimum width that the screen must have so the centers of all the principal maxima formed on either side of the central maximum fall on the screen

Answers

Answer:

1.696 nm

Explanation:

For a diffraction grating, dsinθ = mλ where d = number of lines per metre of grating = 5510 lines per cm = 551000 lines per metre and λ = wavelength of light = 467 nm = 467 × 10⁻⁹ m. For a principal maximum, m = 1. So,

dsinθ = mλ = (1)λ = λ

dsinθ = λ

sinθ = λ/d.

Also tanθ = w/D where w = distance of center of screen to principal maximum and D = distance of grating to screen = 1.03 m

From trig ratios 1 + cot²θ = cosec²θ

1 + (1/tan²θ) = 1/(sin²θ)

substituting the values of sinθ and tanθ we have

1 + (D/w)² = (d/λ)²

(D/w)² = (d/λ)² - 1

(w/D)² = 1/[(d/λ)² - 1]

(w/D) = 1/√[(d/λ)² - 1]

w = D/√[(d/λ)² - 1] = 1.03 m/√[(551000/467 × 10⁻⁹ )² - 1] = 1.03 m/√[(1179.87 × 10⁹ )² - 1] = 1.03 m/1179.87 × 10⁹  = 0.000848 × 10⁻⁹ = 0.848 × 10⁻¹² m = 0.848 nm.

w is also the distance from the center to the other principal maximum on the other side.

So for both principal maxima to be on the screen, its minimum width must be 2w = 2 × 0.848 nm = 1.696 nm

So, the minimum width of the screen must be 1.696 nm

When using science to investigate physical phenomena, which characteristic of the event must exist? predictable repeatable provable readable

Answers

Answer:

Not sure but I believe predictable.

Explanation:

Phenomena usually consists of :

- A history, a date in which the physical phenomenon has occurred.

- A source, a place or reason to why or where the physical phenomena has occured.

According to this, I want to say predictable.

It is not repeatable, there are one-time phenomenons that have occurred that scientists to this day still have not recorded again such as the Big Bang.

It is not provable. Most of the theories earlier scientists and historians have predicted have not yet been proved. Yet rather, somehow, they have been explored and investigated.

It is not readable. This is self explanatory, some things scientists investigate are not written down, nor read. It starts with a mental theory and then immediately goes to the next phase of investigation.

A resistor and an inductor are connected in series to an ideal battery of constant terminal voltage. At the moment contact is made with the battery, the voltage across the inductor is

Answers

Answer:

The voltage is equal to the batteries terminal voltage

Explanation:

Explanation:

If a vacuum pump reduces the pressure of a gas to 1.0 x 10-6 atm, what is the pressure expressed in millimeters of mercury

Answers

Answer:

[tex]1.0\times 10^{-6}[/tex] atmospheres are equivalent to [tex]7.6\times 10^{-4}[/tex] millimeters of mercury.

Explanation:

According to current SI unit conversions, 1 atmosphere is equal to 760 millimeters of mercury. The current pressure is determined by simple rule of three:

[tex]p = \frac{760\,mm\,Hg}{1\,atm} \times (1\times 10^{-6}\,atm)[/tex]

[tex]p = 7.6\times 10^{-4}\,mm\,Hg[/tex]

[tex]1.0\times 10^{-6}[/tex] atmospheres are equivalent to [tex]7.6\times 10^{-4}[/tex] millimeters of mercury.

A mass M is attached to an ideal massless spring. When this system is set in motion with amplitude A, it has a period T. What is the period if the amplitude of the motion is doubled

Answers

Answer:

The period of the motion will still be equal to T.

Explanation:

for a system with mass = M

attached to a massless spring.

If the system is set in motion with an amplitude (distance from equilibrium position) A

and has period T

The equation for the period T is given as

[tex]T = 2\pi \sqrt{\frac{M}{k} }[/tex]

where k is the spring constant

If the amplitude is doubled, the distance from equilibrium position to the displacement is doubled.

Increasing the amplitude also increases the restoring force. An increase in the restoring force means the mass is now accelerated to cover more distance in the same period, so the restoring force cancels the effect of the increase in amplitude. Hence, increasing the amplitude has no effect on the period of the mass and spring system.

When the current in a toroidal solenoid is changing at a rate of 0.0200 A/s, the magnitude of the induced emf is 12.7 mV. When the current equals 1.50 A, the average flux through each turn of the solenoid is 0.00458 Wb. How many turns does the solenoid have?

Answers

Answer:

[tex]N = 208 \ turns[/tex]

Explanation:

From the question we are told that

    The  rate of  current change is  [tex]\frac{di }{dt} = 0.0200 \ A/s[/tex]

    The  magnitude of the induced emf is  [tex]\epsilon = 12.7 \ mV = 12.7 *10^{-3} \ V[/tex]

     The  current is  [tex]I = 1.50 \ A[/tex]

      The  average  flux is  [tex]\phi = 0.00458 \ Wb[/tex]

Generally the number of  turns the number of turn the solenoid has is mathematically represented as  

            [tex]N = \frac{\epsilon_o * I}{ \phi * \frac{di}{dt} }[/tex]

substituting values

           [tex]N = \frac{ 12.7*10^{-3} * 1.50 }{ 0.00458 * 0.0200 }[/tex]

            [tex]N = 208 \ turns[/tex]

       

A long solenoid consists of 1700 turns and has a length of 0.75 m.The current in the wire is 0.48 A. What is the magnitude of the magnetic field inside the solenoid

Answers

Answer:

1.37 ×10^-3 T

Explanation:

From;

B= μnI

μ = 4π x 10-7 N/A2

n= number of turns /length of wire = 1700/0.75 = 2266.67

I= 0.48 A

Hence;

B= 4π x 10^-7 × 2266.67 ×0.48

B= 1.37 ×10^-3 T


What characteristic makes Biology a science, but not Art History?
Using a process of testing ideas and gathering evidence
o Writing books about the subject
O Having a college degree to study it
Discussing and sharing ideas​

Answers

Using a process of testing ideas and gathering evidence.

Answer:

 

Using a process of testing ideas and gathering evidence

Explanation:

c) If the ice block (no penguins) is pressed down even with the surface and then released, it will bounce up and down, until friction causes it to settle back to the equilibrium position. Ignoring friction, what maximum height will it reach above the surface

Answers

Answer:

y = 20.99 V / A

there is no friction    y = 20.99 h

Explanation:

Let's solve this exercise in parts: first find the thrust on the block when it is submerged and then use the conservation of energy

when the block of ice is submerged it is subjected to two forces its weight  hydrostatic thrust

         

              F_net= ∑F = B-W

the expression stop pushing is

              B = ρ_water g V_ice

where rho_water is the density of pure water that we take as 1 10³ kg / m³ and V is the volume d of the submerged ice

We can write the weight of the body as a function of its density rho_hielo = 0.913 10³ kg / m³

             W = ρ-ice g V

              F_net = (ρ_water - ρ_ ice) g V

this is the net force directed upwards, we can find the potential energy with the expression

            F = -dU / dy

            ΔU = - ∫ F dy

            ΔU = - (ρ_water - ρ_ ice) g ∫ (A dy) dy

            ΔU = - (ρ_water - ρ_ ice) g A y² / 2

we evaluate between the limits y = 0,  U = 0, that is, the potential energy is zero at the surface

             U_ice = (ρ_water - ρ_ ice) g A y² / 2

now we can use the conservation of mechanical energy

starting point. Ice depth point

             Em₀ = U_ice = (ρ_water - ρ_ ice) g A y² / 2

final point. Highest point of the block

             [tex]Em_{f}[/tex] = U = m g y

as there is no friction, energy is conserved

            Em₀ = Em_{f}

            (ρ_water - ρ_ ice) g A y² / 2 = mg y

let's write the weight of the block as a function of its density

            ρ_ice = m / V

            m = ρ_ice V

we substitute

             (ρ_water - ρ_ ice) g A y² / 2 = ρ_ice V g y

              y = ρ_ice / (ρ_water - ρ_ ice) 2 V / A

let's substitute the values

             y = 0.913 / (1 - 0.913) 2 V / A

             y = 20.99 V / A

This is the height that the lower part of the block rises in the air, we see that it depends on the relationship between volume and area, which gives great influence if there is friction, as in this case it is indicated that there is no friction

                V / A = h

where h is the height of the block

                 y = 20.99 h

In a two-slit experiment, the slit separation is 3.34 ⋅ 10 − 5 m. The interference pattern is created on a screen that is 3.30 m away from the slits. If the 7th bright fringe on the screen is 29.0 cm away from the central fringe, what is the wavelength of the light?

Answers

Answer:

The wavelength is  [tex]\lambda = 419 \ nm[/tex]

Explanation:

From the question we are told that

   The  distance of separation is   [tex]d = 3.34 *10^{-5} \ m[/tex]

   The  distance of the screen is  [tex]D = 3.30 \ m[/tex]

      The  order of the fringe is  n =  7

     The distance of separation of  fringes is y =  29.0 cm = 0.29 m

   

Generally the wavelength of the light is mathematically represented as

          [tex]\lambda = \frac{y * d }{ n * D}[/tex]

substituting values

         [tex]\lambda = \frac{0.29 * 3.34*10^{-5} }{ 7 * 3.30}[/tex]

        [tex]\lambda = 4.19*10^{-7}\ m[/tex]

        [tex]\lambda = 419 \ nm[/tex]

A spring attached to the ceiling is stretched 2.45 meters by a four kilogram mass. If the mass is set in motion in a medium that imparts a damping force numerically equal to 16 times the velocity, the correct differential equation for the position x (t ), of the mass at a function of time, t is

Answers

Answer:

d²x/dt² = - 4dx/dt - 4x is the required differential equation.

Explanation:

Since the spring force F = kx where k is the spring constant and x its extension = 2.45 equals the weight of the 4 kg mass,

F = mg

kx = mg

k = mg/x

= 4 kg × 9.8 m/s²/2.45 m

= 39.2 kgm/s²/2.45 m

= 16 N/m

Now the drag force f = 16v where v is the velocity of the mass.

We now write an equation of motion for the forces on the mass. So,

F + f = ma (since both the drag force and spring force are in the same direction)where a = the acceleration of the mass

-kx - 16v = 4a

-16x - 16v = 4a

16x + 16v = -4a

4x + 4v = -a where v = dx/dt and a = d²x/dt²

4x + 4dx/dt = -d²x/dt²

d²x/dt² = - 4dx/dt - 4x which is the required differential equation

A toroidal solenoid has 590 turns, cross-sectional area 6.20 cm^2 , and mean radius 5.00 cm .Part A. Calcualte the coil's self-inductance.Part B. If the current decreases uniformly from 5.00 A to 2.00 A in 3.00 ms, calculate the self-induced emf in the coil.Part C. The current is directed from terminal a of the coil to terminal b. Is the direction of the induced emf froma to b or from b to a?

Answers

Complete Question

A toroidal solenoid has 590 turns, cross-sectional area 6.20 cm^2 , and mean radius 5.00 cm .

Part A. Calculate  the coil's self-inductance.

Part B. If the current decreases uniformly from 5.00 A to 2.00 A in 3.00 ms, calculate the self-induced emf in the coil.

Part C. The current is directed from terminal a of the coil to terminal b. Is the direction of the induced emf from a to b or from b to a?

Answer:

Part A  

       [tex]L = 0.000863 \ H[/tex]

Part B  

       [tex]\epsilon = 0.863 \ V[/tex]

Part C

    From terminal a to terminal b

Explanation:

From the question we are told that

      The  number of turns is  [tex]N = 590 \ turns[/tex]

      The cross-sectional area is  [tex]A = 6.20 cm^2 = 6.20 *10^{-4} \ m[/tex]

      The  radius is [tex]r = 5.0 \ cm = 0.05 \ m[/tex]

       

Generally the coils self -inductance is mathematically represented as

              [tex]L = \frac{ \mu_o N^2 A }{2 \pi * r }[/tex]

Where [tex]\mu_o[/tex] is the permeability of  free space with value [tex]\mu_o = 4\pi * 10^{-7} N/A^2[/tex]

substituting values

             [tex]L = \frac{ 4\pi * 10^{-7} * 590^2 6.20 *10^{-4} }{2 \pi * 0.05 }[/tex]

             [tex]L = \frac{ 2 * 10^{-7} * 590^2 6.20 *10^{-4} }{ 0.05 }[/tex]

             [tex]L = 0.000863 \ H[/tex]

Considering the Part B

      Initial current is [tex]I_1 = 5.00 \ A[/tex]

      Current at time t is [tex]I_t = 3.0 \ A[/tex]

       The  time taken is  [tex]\Delta t = 3.00 ms = 0.003 \ s[/tex]

The self-induced emf is mathematically evaluated as

          [tex]\epsilon = L * \frac{\Delta I}{ \Delta t }[/tex]          

=>         [tex]\epsilon = L * \frac{ I_1 - I_t }{ \Delta t }[/tex]

substituting values

             [tex]\epsilon = 0.000863 * \frac{ 5- 2 }{ 0.003 }[/tex]  

             [tex]\epsilon = 0.863 \ V[/tex]

The direction of the induced emf is  from a to b because according to Lenz's law the induced emf moves in the same direction as the current

This question involves the concepts of the self-inductance, induced emf, and Lenz's Law

A. The coil's self-inductance is "0.863 mH".

B. The self-induced emf in the coil is "0.58 volts".

C. The direction of the induced emf is "from b to a".

A.

The self-inductance of the coil is given by the following formula:

[tex]L=\frac{\mu_oN^2A}{2\pi r}[/tex]

where,

L = self-inductance = ?

[tex]\mu_o[/tex] = permeability of free space = 4π x 10⁻⁷ N/A²

N = No. of turns = 590

A = Cross-sectional area = 6.2 cm² = 6.2 x 10⁻⁴ m²

r = radius = 5 cm = 0.05 m

Therefore,

[tex]L=\frac{(4\pi\ x\ 10^{-7}\ N/A^2)(590)^2(6.2\ x\ 10^{-4}\ m^2)}{2\pi(0.05\ m)}[/tex]

L = 0.863 x 10⁻³ H = 0.863 mH

B.

The self-induced emf is given by the following formula:

[tex]E=L\frac{\Delta I}{\Delta t}\\\\[/tex]

where,

E = self-induced emf = ?

ΔI = change in current = 2 A

Δt = change in time = 3 ms = 0.003 s

Therefore,

[tex]E=(0.000863\ H)\frac{2\ A}{0.003\ s}[/tex]

E = 0.58 volts

C.

According to Lenz's Law, the direction of the induced emf always opposes the change in flux that causes it. Hence, the direction of the induced emf will be from b to a.

Learn more about Lenz's Law here:

https://brainly.com/question/12876458?referrer=searchResults

A typical ten-pound car wheel has a moment of inertia of about 0.35kg *m2. The wheel rotates about the axle at a constant angular speed making 70.0 full revolutions in a time interval of 4.00 seconds. What is the rotational kinetic energy K of the rotating wheel? Express answer in Joules

Answers

Answer:

The  rotational kinetic energy is  [tex]K = 2116.3 \ J[/tex]

Explanation:

From the question we are told that

    The moment of inertia  is  [tex]I = 0.35 \ kg \cdot m^2[/tex]

    The number of revolution is N  =  70 revolution

     The  time taken is  t  =  4.0  s

   

Generally the angular velocity is mathematically represented as

      [tex]w = \frac{2 \pi N }{t }[/tex]

substituting values

      [tex]w = \frac{2* 3.142 * 70 }{4 }[/tex]

       [tex]w = 109.97 \ rad/s[/tex]

     

The rotational kinetic energy K i mathematically represented as

       [tex]K = \frac{1}{ 2} * I * w^2[/tex]

substituting values

       [tex]K = \frac{1}{ 2} * 0.35 * (109.97)^2[/tex]

       [tex]K = 2116.3 \ J[/tex]

Niobium metal becomes a superconductor when cooled below 9 K. Its superconductivity is destroyed when the surface magnetic field exceeds 0.100 T. In the absence of any external magnetic field, determine the maximum current a 5.68-mm-diameter niobium wire can carry and remain superconducting.

Answers

Answer:

The current is  [tex]I = 1420 \ A[/tex]

Explanation:

From the question we are told that

   The  diameter of the wire is  [tex]d = 5.68 \ mm = 0.00568 \ m[/tex]

    The  magnetic field is  [tex]B = 0.100 \ T[/tex]

   

Generally the radius of the wire is mathematically evaluated as

       [tex]r = \frac{d}{2}[/tex]

substituting values

     [tex]r = \frac{ 0.00568}{2}[/tex]

     [tex]r = 0.00284 \ m[/tex]

Generally the magnetic field is mathematically represented as

       [tex]B = \frac{\mu_o * I}{ 2 \pi r }[/tex]

=>    [tex]I =\frac{ B * 2 \pi r }{\mu_o}[/tex]

Here [tex]\mu_o[/tex] is the permeability of free space  with value [tex]\mu_o = 4 \pi *10^{-7} N/A^2[/tex]

substituting values

=>     [tex]I =\frac{ 0.100 * 2 * 3.142 * 0.00284 }{ 4 \pi * 10^{-7}}[/tex]

=>     [tex]I = 1420 \ A[/tex]

A particle with charge q and momentum p, initially moving along the x-axis, enters a region where a uniform magnetic field* B=(B0)(k) extends over a width x=L. The particle is deflected a distance d in the +y direction as it traverses the field. Determine the magnitude of the momentum (p).

Answers

Answer:

Magnitude of momentum = q × B0 × [d^2 + 2L^2] / 2d.

Explanation:

So, from the question, we are given that the charge = q, the momentum = p.

=> From the question We are also given that, "initially, there is movement along the x-axis which then enters a region where a uniform magnetic field* B = (B0)(k) which then extends over a width x = L, the distance = d in the +y direction as it traverses the field."

Momentum,P = mass × Velocity, v -----(1).

We know that for a free particle the magnetic field is equal to the centrepetal force. Thus, we have the magnetic field = mass,.m × (velocity,v)^2 / radius, r.

Radius,r = P × v / B0 -----------------------------(2).

Centrepetal force = q × B0 × v. ----------(3).

(If X = L and distance = d)Therefore, the radius after solving binomially, radius = (d^2 + 2 L^2) / 2d.

Equating Equation (2) and (3) gives;

P = B0 × q × r.

Hence, the Magnitude of momentum = q × B0 × [d^2 + 2L^2] / 2d.

A loop of wire is at the edge of a region of space containing a uniform magnetic field B. The plane of the loop is perpendicular to the magnetic field. Now the loop is pulled out of this region in such a way that the area A of the coil inside the magnetic field region is decreasing at the constant rate c. That is, dA/dt=−c, with c>0.Required:a. The induced emf in the loop is measuredto be V. What is the magnitude B of the magnetic field that the loop was in?b. For the case of a square loop of sidelength L being pulled out of the magneticfield with constant speed v, What is the rate of change of area c= -dA/dt

Answers

Answer:

The question is not clear enough. So i have attached a copy of the correct question.

A) B = V/c

B) c = Lv

Explanation:

A) we know that formula for magnetic flux is;

Φ = BA

Where B is magnetic field and A is area

Now,

Let's differentiate with B being a constant;

dΦ/dt = B•dA/dt

From faradays law, the EMF induced is given as;

E = -dΦ/dt

However, we want to express it in terms of V and E.M.F is also known as potential difference or Voltage.

Thus, V = -dΦ/dt

Thus, we can now say that;

-V = B•dA/dt

Now from the question, we are told that dA/dt = - c

Thus;

-V = B•-c

So, V = Bc

Thus, B = V/c

B) according to Faraday's Law or Lorentz Force Law, an electromotive force, emf, will be induced between the two ends of the sidelength:

Thus;

E =LvB or can be written as; V = LvB

Where;

V is EMF

L is length of bar

v is velocity

From the first solution, we saw that;

V = Bc

Thus, equating both of the equations, we have;

Bc = LvB

B will cancel out to give;

c = Lv

Explanation:

) Calculate current passing in an electrical circuit if you know that the voltage is 8 volts and the resistance is 10 ohms

Answers

Explanation:

Hey, there!

Here, In question given that,

potential difference (V)= 8V

resistance (R)= 10 ohm

Now,

According to the Ohm's law,

V= R×I { where I = current}

or, I = V/R

or, I = 8/10

Therefore, current is 4/5 A or 0.8 A.

(A= ampere = unit of current).

Hope it helps...

Given three resistors of different values, how many possible resistance values could be obtained by using one or more of the resistors?

Answers

Answer:

8 possible combinations

Assuming R 1, R 2 and R 3 be three different Resistance

1- all three in series

2-all three in parallel

3- R 1 and R 2 in series and parallel with R 3

4-R 1 and R 3 in series and parallel with R 2

5-R 2 and R 3 in series and parallel with R 1

6- R 1 and R 2

in parallel and series with R 3

7-R 1 and R 3 in parallel and series with R 2

8-R 2 and R 3 in V with R 1


A collector that has better efficiency in cold weather is the:
flat-plate collector due to reduced heat loss
evacuated tube collector due to its larger size
flat-plate collector due to the dark-colored coating
O evacuated tube collector due to reduced heat loss
Question 23 (1 point) Saved
One of the following is not found in Thermosyphon systems
o

Answers

Answer:

D. evacuated tube collector due to reduced heat loss

Explanation:

Evacuated tube collectors has vacuum which reduces the loss of heat and increase the efficiency of the collector. It has a major application in solar collector, and converts solar energy to heat energy. It can also be used for heating of a definite volume of water majorly for domestic purpose.

During cold weather, the conservation and efficient use of heat is required. Therefore, evacuated tube collector is preferred so as to reduce heat loss and ensure the maximum use of heat energy.

Other Questions
How do i do this equation -3(-2y-4)-5y-2= Which relationships have the same constant of proportionality between yyy and xxx as the equation y=\dfrac{1}{2}xy= 2 1 xy, equals, start fraction, 1, divided by, 2, end fraction, x? Choose 3 answers: Choose 3 answers: (Choice A) A 6y=3x6y=3x6, y, equals, 3, x (Choice B) B (Choice C) C (Choice D) D xxx yyy 222 111 333 2.52.52, point, 5 444 333 (Choice E) E xxx yyy 444 222 555 2.52.52, point, 5 101010 555 What is the measure of circumscribed LX?O 45O 50O 90O 950 Which of the following is a testable hypothesis?a. Roses are more beautiful than violets.b. A plant needs at least five hours of sunlight per day to grow.c. I've cream is delicious.d. Humans will someday land on Mars. Correctly label the below as simple, complex, compound, compound-complex, or sentence fragment. 1.Vampires Dairies is my favorite television show, but I also love True Blood. 2.Juan, Sam and Marie went to a movie, ate popcorn, and walked around the mall. 3.After the officer pulled Tim over, Tim began to cry, and the officer took pity on him. 4.Running after the car, the dog barked until the car was out of sight. 5.I love skiing, my brother loves snowboarding, and my sister likes snow tubing. 6.We ordered pork tenderloin for our entre and scalloped potatoes for our side dish. 7.Although he hasnt read the book, he has decided to write a book report on it. 8.I saved my money so that I could buy an iPad. 9.I love eating turkey at Thanksgiving, but my friends family eats lasagna because his cousin is allergic to poultry. 10.Because you dont understand me. What is the square root of 48? what is the square root of 1/49 ? what is the square root of 4/100 ? The diagonal of rhombus measure 16 cm and 30 cm. Find it's perimeter Which statement is true regarding the traits of scatterplots?A) The strength of a correlation is independent of whether the correlation of a scatterplot is positive or negative. A scatterplot with positive correlation can have either weak correlation or strong correlation.B) The slope of a line is independent of whether the correlation of a scatterplot has positive or negative correlation. A scatterplot with a negative slope can have either positive correlation or negative correlation.C) The nonlinear association of a scatterplot depends on whether it has a weak or strong correlation. A scatterplot with nonlinear association will have a strong correlation.D) The nonlinear association of a scatterplot depends on whether it has a positive or negative correlation. A scatterplot with nonlinear correlation will have a negative correlation. The number of pages per book on a bookshelf is normally distributed with mean 248 pages and standard deviation 21 pages. Using the empirical rule, what is the probability that a randomly selected book has less than 206 pages? You take out a car loan for 13,381 dollars. If your loan has an annual interest rate of 8.86 percent, and you will make monthly payments for 5 years, how much of your first payment will go towards principal (go towards paying down the outstanding loan balance)? Waterways were an important means of transportation in Ohio in the 19th century. How did Ohioans modify their environment to improve transportation on their waterways? What is a definitiveness complex? How should a writer avoid this? 20 POINTS!!! Please Help! No nonsense answers please! Here are the ages (in years) of 10 professors at a college. , 47, 44, 48, 43, 35, 65, 56, 37, 7351 What is the percentage of these professors who are younger than 50? The eye light and associates governments affirm that Germany excepts the responsibility of Germany and her allies for causing all the loss and damage to which the allied and associated governments there nationals have been subjected as a consequence of war imposed upon them by aggression of Germany and her alliesWhy were there clauses probably inserted ?What benefits did these classes give the Allies? An arrangement where a property developed by the seller is sold to a buyer. The seller retains occupancy of the premises by signing a lease with the buyer. The seller, now the tenant, pays taxes, utilities, insurance and operating costs. This is called a ___________. This is a common practice for Walmart and Rite-Aide and many other businesses Group of answer choices sale rental agreement net lease investment lease-purchase option nome of the other answers What community do you live in?Name two places in your community?What is your favorite place to visit in your community and why? =Graphing an integer function and finding its range for a given...The function h is defined as follows for the domain given.h(x) = 2 -2x, domain = {-3, -2, 1, 5}Write the range of h using set notation. Then graph h. A trader maintains a position in a small capitalization stock that has low trading volume. The trader has a high level of which of the following risks?A) MarketB) LiquidityC) BusinessD) Inflation Question. 1 The product of a monomial and a binomial is a (a) monomial (b) binomial (c) trinomial (d) None of these